A used 3D printer can be a great deal, but it needs a thorough cleaning and maintenance to ensure optimal performance. This video will guide viewers through the process, from removing dust and debris to lubricating moving parts, ensuring they get the most out of their new-to-them 3D printer.
Dont forget, if you want to donate to the channel, send me some btc at : bc1qxpdkefehzj5nwcectn3yj8am9pw04t7ucpy0ax ! or leave atip on the video!
Hey folks, TechNibbers here. This is a printer that I've just decided I'm going to take out
of mothballs that's been sitting around for a while. I did get some extensive use out of it.
However, this video is to show you how to maintain your printer or bring it back to life after it
sits for a while, or more specifically, if you buy a used printer, and the Ender 3 is very,
very common on the second-hand market, how to check and make sure that everything is
properly connected and hooked up right before you move on to turning it on. And I do have it
plugged in. Your first urge may be to just turn the machine on and see if it works. But first,
there are a few things you want to check before even powering it up, let alone trying to home
the machine. So here we have it. This is actually a pretty heavily modified Ender 3 V2. As you can
see, it's collected quite a bit of dust. It's kind of just been sitting in my non-working printer
bay over there in the basement here for a couple of months. Not exactly an ideal place to leave
a mechanical device for long periods of time. And I have no reason to suspect if I fire it up,
it won't just turn on. But before I turn it on, I wanted to check a couple of things.
First and foremost, before I power up the device, one of the things I'm going to check are the
exposed connections, just to make sure that everything's plugged in properly. Now, most of
the mechanics of this device are down here with the actual board that runs it. So I'm fairly certain
those are all plugged in. I'm not going to take the bottom off. But there are some other plugs,
such as on the screen here, that may need a little bit of attention. This one looks like
it's in a little bit crooked, so I'll just push that in all the way. And specifically,
one of the other things you want to look at is the bed connection back here. Now, this piece
that looks like it's at an angle is actually just a bracket to hold it in place. The actual
connection is going to be underneath here. So I'm just going to take a look, and it looks like
everything's hooked up. There's an easy remove clip here on this version. Now, the original
Ender 3 and the Ender 3 Pro don't have this, so it's safe to assume on this printer it's connected.
If you don't have something securing it like I do, you're definitely going to want to check and make
sure that that is connected as well. The rest of these cables here, coming from the hot end,
are basically going to all go down to the motherboard down there. And like I said,
I'm fairly certain those are plugged in. So next, it's on to a few other things. One of the major
things that happens with printers that sit too long and collect dust is the Z-axis gets a little
bit gross. Now, this one I can feel is very dry, and it should be. It shouldn't be completely greasy,
but I might just add a couple drops of lubricant to the riser on the Z-axis rod here to ensure
that it moves smoothly when I start the machine. So let's go ahead and grab a little machine grease.
So the first thing we're going to want to do with any printer that we're trying to restyle or refurb
is take care of any dust that may be left over on the machine, because we're going to be lubing
up some parts and removing some parts and reaching in places and checking things out. But as you may
know, dust and mechanical components are not really good bedfellows. So we're going to clean them up
as best as we can. Look it over once or twice. Now, I've already dusted most of this off because
I didn't want to show you how atrocious it actually was when I pulled it from mothballs,
but there is still quite a bit of mess left on pieces of this. We're just going to get it as
clean as we can so that none of those spots cause us an issue in the future. And once we have it all
cleaned up, now we're ready to actually do some maintenance. One of the first things you're going
to want to do is get yourself some tube grease. And by the way, I did dust this rod because we
don't want it filling with dust and gunking it up or anything grainy. And I'm going to apply
a fair amount to the rods just above and below the riser that rides on the Z
rod. So that is this guy right here. And as you can see, if I zoom a little closer here,
as well as the fact that I didn't clean that well enough, I did get a little gob of the grease on
both sides. So now I'm just going to leave that. And you should have a motor attached there if it's
an Ender 3. If you have a direct drive printer, the motor will be on top of the gantry and not
here. So it's a little bit easier to lube that up all around. So that is our first step. Now,
you can, if you want, manually turn it a little bit and make sure it's rising and running smoothly.
And this one is actually really smooth, but I wouldn't recommend turning the motors too much
by hand. What you're really going to want to do is wait until you have the machine on,
and then you're going to test it out. That will increase the distribution of the grease that
we've added here and ensure that the parts that the machine needs to ride on are adequately lubed.
After we're done with that, the next thing we're going to check is the eccentric nuts. Now,
an eccentric nut is a nut that the hole is not in the center. And the reason for that is as you
turn the nut, you can adjust the distance between the rod that goes through the nut
and another surface. In this case, the contact surface we're talking about is this vertical
piece of V-mold railing here. And the eccentric nut is on the inside wheel. These other two
have spacers. This one is actually a nut, and I can show that to you real quick here.
You see the typical hexagonal shape of an eccentric nut. Over here you see spacers. The
best way to test if the nut needs to be tightened on the gantry is to try and wiggle it a little
bit. And if you don't see it sliding up and down the rail as you wiggle it, it's tightened and
adjusted properly. There is also an eccentric nut on the wheel of the bed. On this printer,
it's actually in the front. And these are for leveling the bed. Those are the wheels it
actually rides on. So there is an eccentric nut there. If I can get it to focus, you can see it,
and that needs to be tightened as well. And the way to tell if that's tight is to grab the bed
and just give it a little wiggle. And if it seems loose, you're going to need to reach down there,
tighten that up against the rail. And the last thing we're going to check before we fire up
our machine is the tension on the belts. We're going to do that by adjusting the knob at the
front of the Y-axis and the side of the X-axis. Now, the best way to tell if your belt's tight
enough is to give it a little strum. You should get a little reverberation like a guitar string
there. So you can usually pluck these ones from the bottom, and these seem to be tight enough.
If it's not tight or it's too tight, you can adjust it using these wheels. Now, this one is
not from an Ender 3. There's usually a little black knob here or a blue one like that one. I
stole this from a TiVo Tarantula because I thought it looked cooler and it was bigger for a little
bit more fine control. So we're finally ready to turn the machine on. So I flipped the switch in
the back and you can see here that everything seems to be working properly. I'm going to go
ahead and home the machine. Now, we have a few more maintenance things we can do before we need
to print, such as leveling the bed. So I'm going to show that real quick here. Now, modern systems
have an ABL system where you can just auto bed level, but if you're using the paper method,
you're going to want to go to every corner and adjust the wheels until it is just snug enough
to move the paper slightly in between. Then you're going to want to do it again and go around
diagonally. Now that I've got the bed all leveled out, we're going to run a few test prints. One of
the first things we're going to print is a calibration cube, and we do that because it's
specified size and we can measure it and make sure we're extruding properly. However,
you should expect to run into a few hiccups at first because, you know, not everything in life
is perfect. So the problem I was having here was it was too close to the bed. That wasn't because
of leveling. It was a Z offset problem. So I adjusted the Z offset a little bit, which I can
post a video about in the corner, and I ran it again. This time it started off way better. However,
my lost adhesion, as you can see, and the piece had to be started a third time. So I adjusted my
Z offset once again. All right, so we are up and printing, and when I'm done printing this,
I'm going to measure the cube itself and see if it's the dimensions we specified. And from there,
I can make some other minor adjustments. So now from here, basically all we need to do
is the basic stuff you would do to a new printer to make sure it's calibrated properly,
which is run a few test prints and maybe make some minor adjustments. Now I'll link to a series
that will give you some hot tips on what to do next up here, especially for the Ender 3,
but it works on pretty much all these old Cartesian style machines, such as the old
artilleries and the A-nuts. We'll be pulling some of them out of mothballs here shortly,
and also getting this awesome artillery over here I have running.
So there you have it, folks. The used printer is all back up and running. Everything seems
to be in working order. If you need more in-depth videos on this or any printer like it, such as the
Cartesian machines behind me, I will put up a link in the corner here. Feel free to check that out.
It will also give you the next steps, which is basically to do all of the test printing
and calibration you would do if you purchased a new printer, just to make sure that everything
is running as smoothly as possible and up to your specs. So that's going to be it for this video,
guys. If it was helpful, please subscribe, leave a like down below, and leave me a comment on any
specific questions you have regarding this machine. I'll see if I can point you in the
direction of a video because I probably already have it, and if not, you might get lucky. I might
make one just for you. TechNiverse out.