Cabochon Demonstration With Larry Carby | William Holland School Of Lapidary Arts
Aug 24, 2026
Instructor Larry Carby shows us the process of making a trio of cabochons.
AI Generated·May contain errors
Good morning. Larry Kirby, one of the calving instructors here at William Holland.
Today we're going to do a demonstration on calving. I've got some material that's a new
find out of Nevada. It's called Wonderstone, but what the Wonderstone everybody's familiar with
is the Wonderstone out of Utah. This was just discovered the first time I saw it on the market
was in Arizona in January. So we're going to cut one up. It's a harder material than the old
Wonderstone is. We have a couple of places that we can use here. That's one of the things that
people ask, well, where do you know where to cut a calve at? And I tell them, well,
you just look at the features. So you've got a nice feature here. You would have a nice feature
here. Today we're going to use this feature and it's prettier on this side to me than the other
side. So what I want to do is mark my template on the back. There's lots of different shapes.
We're going to be cutting a trio today as well with earrings. So what I do with all my classes,
I start out with a standard 40 by 30 oval. And that's what we're going to do for the demo. So
everybody knows what we're doing in class. So what we're going to do is lay that there
and you will see that pattern on the other side, which should be the top of the stone when we get
done. So I just lay that here, take a sharpie marker and outline where the calve is going to be
just like that. And like I said, today we're going to be doing a trio.
So I'm going to come back in with this long oval and lay out a pair up here in this other
nice area. It's going to have the same colorations and everything as the big one,
but we'll lay it out like this and that will be the earrings. All right, once you've laid it out
like that, some people ask, you know, if you're going to do a trio, if you're doing the earrings
with this particular case, we're doing the same shape. But if you have, and there's no
one side to it, but if you were doing a pattern, let's say this particular pattern here and this
was going to be your earrings, you always want to make them a mirror image if you can. So what
you would do in this case would be you would draw your outline on one side of the template and then
turn your template over and draw your other earrings. So they would be a mirror image when
you have them laid out. But since we're not really worried about that today, they're going to be
basically the same shape, just a long oval versus a regular oval. We'll go with this. And one of
the things you want to do is when you're first starting out, particularly, is line your area
where you want to make your saw marks. And what I do is I just take the template and lay it down
here like this. Get fairly, get fairly close to your cab and run your lines across like that.
The more you can cut off with a saw, the less time it'll take you on the machine. This particular
one is not 100% square, so we won't have quite as many lines to work. So we're going, when we go to
the saw, we're going to follow these lines and then come back and grind to shape on the machine.
Okay, we're over to the saw. Make sure the water comes up on your blade, which this one has.
If this particular saw is a six-inch trim saw made by High Tech Diamond, this is the saw that
I run at home. When you turn this saw on, if you'll watch the water coming off the blade,
you can see exactly where the saw blade is going to be. And what you want to do is lay that water
line coming right straight down the line that you want to cut, which is right here. And then we're
ready to start on the cabbing machine. When we get ready to get into the cabbing machine,
I want to make sure that the water is about halfway up the spitter that wets the wheel.
And you always put the spitter in first before you turn the machine on. And we're going to start
out on the 80 grit wheel, which is the first wheel, and I'll put it in and then turn the
machine on. Make sure you're getting plenty of water up on the wheel as it starts to get the
wheel good and wet before you ever start grinding on it. What you want to do as you're grinding the
cab, you want to hold this and work it about 90 degrees, as close to 90 degrees to the wheel
as you can get it. When you're cutting, you want to make sure you use the entire surface of the
wheel, not just get right in the middle. Or you wear the wheel out in the middle and the two edges,
outside edges, will still be good. What I'm doing is just working my way around the wheel,
moving down toward the design line. What you want to do is get down to that mark.
We're going to cut a calibrated, what's called a calibrated cab today. And the reason you would
cut a calibrated cab is if somebody has a pre-made bolo or a belt buckle or a pendant,
it has to be an exact size. And the calibrated would give you that to where you will have the
exact size that you need to go in there. Particularly on a hard stone like this,
you don't want to press too hard because it will cause it to chip out around the edges
if you're pressing too hard on it. Let the wheel do the work. And the way you get a calibrated
cab, you take the same template we used to mark the stone and you get it to where it will just
barely fit through that template. Not quite there, just a couple little high spots, but we're
very close. Keep checking it, cut a little and keep checking it until you get it there.
That one's almost ready. But if you don't get it small enough, then it won't go into a pre-made
piece of jewelry, whether it be a belt buckle or a pendant or whatever, a bolo tie.
If you get it too small, then it will rattle around. So everybody needs to know how to cut
a calibrated cab as well as a pre-point. There it is. That's called a calibrated cab.
You just have to be sure as you're finishing the cabbing, you don't take any more off of it
to make it too small. All right, we're going to finish up the earring. One of the things you want
to do as you finish up, if you have it here, both of them, I always like to lay them together
to see if I've got the shapes exact and these are close as you're going to get in most cases.
Same length. The next step is going to be when you finish up with your machine,
always take your spitter out before you turn the machine off. The next thing we're going to
wipe them down and go into putting a bezel line where the flat edge around the outside of the
stone. Some people call it a girdle or bezel, whichever. What we're going to be talking about
is the flat edge on the outside of the stone that's going to remain flat that wire wrappers
would use to put their wire around or if you were setting them in silver, you would have something
to put your bezel wire up next to. The industry standard is two to three millimeters for a bezel.
Some people say two, some people say three. I say two to three. In my classes, I use a caliper
to mark the stones and what I do is I lock the caliper on 2.5, so we're halfway between the two
and the three. I have a caliper over here, it's already locked at 2.5 millimeters. What you want
to do is wherever the back of the stone is, in this case this side, this is going to be the front,
you want to mark the back. I'm going to put the caliper down, come in here and put this right on
the edge and then mark a spot on my stone at 2.5 millimeters and that will be the width of the flat
area this side. What I do is I mark one of the stones where the bezel line needs to be
and then what you do is you take your marker and you lay it on a pencil, preferably round,
and you move the in and out and that adjusts the height of the point of the marker. So,
right there it is. Can you see it all right on the mark here and then you hold this still with
your right hand and then turn your stones and that puts your bezel line on exactly where you
want it all the way around and then you do that with any other stones that you've got that are
ready to cut. You do the same thing and I'm putting the line exactly the same place all the way around
the stones that I'm going to cab right now and that's the way you do it. The next step will be
putting them on a drop stick so we can finish them up. Okay, so you want to put the stones,
the back side up because that's where your drop stick is going to go.
That side will be up. This is going to be the back so you put them on there so they can get warm
and then you pick out the appropriate size drop sticks for what you're doing and I don't know
what's in here. A little big but that's all right and I like to I like to warm my drop sticks up as
well so I lay mine on my drop pot at home. I lay them up on the edge where the drop stick and the
and the stone both get heated up at the same time. All right, so what we're at the drop pot we've got
the stones are hot and I always lay my drop sticks up here and get them warm as well and what you do
is you just get a nice amount of drop wax on the stick and then force it set it down right in the
of your stone and if it doesn't set in good now that's hot I'll wet my finger
and press it in just a little bit all the way around to make sure it sets on the on the dot
on the uh cab real well. Okay now that we've got them docked we're ready to go back to the
cabbing machine and start making your cab and the first thing that what you want to do is you want
to go in and cut an angle approximately 30 degrees down to the bezel line but you do not want to cut
that bezel line out because you need that flat edge around the outside for either wire wrap or
silversmithing whichever you want to do. A lot of people will come in and they'll try to do about
a 15 degree angle and then they'll try to start trying to dome it over and you have to get your
angles cut in here very well before you can ever start doming or they will not dome they'll always
be flat on top. So again put your spitter is what it's called into the end of the machine before
you turn it on put it under your wheel we'll start again at the 80 grit wheel and then work our way
across the machine again we're working across using the whole wheel and not just the middle
some people will work try to do a 45 first i like to do the 30 once you get the 30 you see where
you're at and how much more you have to cut and then you can go to a 60 if you need to
and there you are at about a 30 degree angle all the way around down to the line
but the line is still there but we're going to have to get a lot more of an angle in before you
could ever dome if you try to start doming and rocking that back and forth doming how to dome
this it will not dome you'll wind up with a flat top so it's got to cut be cut into an angle more
like a 60 degree which is what we'll do now and again we're going to cut it down to the bezel line
now you can see you're getting the center down the word you getting close to being able to dome
you just need a little bit more work in off of each side and off of each end before you then
you can start rocking the stone back and forth turning and rocking and that will make your dome
sometimes you have to watch this particular stone the darker colors in here are a little bit softer
than the lighter color so you have to kind of be easy and not put much pressure on or you'll cut
you can cut too deep into your color area when we start doming we're going to go try to go from
bezel line to bezel line without without taking the line out okay all right at this point we want
to move over to the next wheel a 220 grit basically we're going to do the same thing
is we're going to go around the edges and then bring it across the dome
okay now we're going to move on over the 280 these are the softer wheels
they'll kind of shape themselves to the to the stone as you're cutting on them
but you're going to do basically the same thing from here on out you're going to work it around
the edge and then polish it and then work on the dome this is a very important step if you don't
get all the scratches out from the first two wheels here when you get over you're about finished
with your with your cabochon you'll have scratches in it you'll have to come back to here
you want to see if you've got scratches you always have to get your stone dry all wet stones look
good they have to be dry before you can see a scratch or a flat spot in there i don't see
anything at this point they may show up a little later but right now i don't there is a little
bug right here in the stone but all that does is tell you it's a natural stone the next step is
we're going to start cleaning up the bezel and what you want to do is just come around here
enough to get any little chips out of it and get rid of your line that we put in when we started
you want to get it at 90 degrees or as close as you possibly can and just turn the stone right
around on that until the bezel the bezel line is gone now we'll move to the other side and
we're going to do exactly the same thing for these three wheels and then we have the polish
machine over this goes 600 grit and the polish machine over on the other 8 14 and 50 000 and
then we'll build the machine with zinc my camera person katie just saw a couple of scratches that
old bland larry can't see and they're right here and here's a little trick
if you've got scratches you can take your marker and go over your scratches
and the marker will get down in those scratches we're going back to the now i can see them once
i put them on there there are some scratches right in the middle right here once you get
rid of the marker on that 280 wheel if the scratches will be gone as well good catch katie
by the way now you can really see them there that's where the scratches are the easiest way
these scratches were running this way the wheel is coming here i want to want to work the work
over that area at 180 from the way the scratches are running that's the way you get them out and
know they're gone all right thank you basically you're going to do the same thing across these
last three wheels that we did with this with the 280 and instead of working the bezel last
i work it first as a general rule i'll go ahead and come around here about three two or three times
and then i'll do the same thing come around and then rock it off you want to put enough weight
enough pressure in to kind of indent those foam back wheels so it conforms to your to your
cabochon not a whole lot of pressure but enough that you can feel it kind of indent the wheels
just a little bit let's look at these first these are the three the trio that we finished on the
other machine so now we're coming to the to the polish machine and this machine has the three
wheels on it been changed this is an eight thousand fourteen thousand and a fifty thousand
so we're going to run these through these wheels exactly the way we did the last three wheels on
the other machine except it's just a different grip put a better polish on go to the final step
which will be the the zam polish on the buffer over here but this is what they look like when
when you're using this machine you must hold on to these very tight
and snatch it right out of your hand back into that steel backing back here
you know this is actually like 130 000 instead of the 50 000 this is like 130 000
once we've got them off the dot stick we're going to clean up the back a little bit there's a little
bit of rough edge right around the corner we're going to do that at about a 45 degree angle
and and then just if there's any saw marks on the back of the stone you want to clean them up
these three pieces do not have any saw marks so you see a little bit of it on the tip here
it's got a couple little chips that we're going to take out and then you're done you have a
cabochon that's ready to be made into a piece of jewelry what i usually do is i'll start on the 280
to do this and i go with the 45 first just come around here and knock that little sharp edge
if there's any little chip outs in it take care of that and then once you get the chip outs in
the way you clean up the back there's a little bit of uh stop wax or anything left on it just
put it on your fingers and just make a circle like this on the wheel turn it do the same thing
and i'll usually go over to this side at least through the 600 wheel or maybe the 12
but i'll do that and it's like i said if there's any saw marks on the back
or in the slab you want to make sure to get all those out and you're done

