How Nitrogen Generation Works - Liberty Systems Episode 2

Neo Structure
3 followers
Aug 14, 2026
At SendCutSend, nitrogen is one of the biggest operating costs in our shop. That's why we've invested in nitrogen generation to help keep our lasers running 24/7.
In this episode, Jim is joined by Matt from Liberty Systems for a behind the scenes look at how our nitrogen generation setup works. From compressing atmos
AI Generated·May contain errors
Hey guys, I'm Jim. I joined today with Matt from Liberty Systems. We're doing a vendor spotlight
and kind of behind the scenes on how we work with some of our vendor partners.
Liberty Systems has been an awesome partner for us for many many years and today Matt is gonna
actually go through like how this whole system works. We use bulk nitrogen at all of our
facilities. This is I think the biggest system that we have though. We're at our Reno facility
and we're gonna walk through how this works, how does it save us a bunch of money over bulk because
we spend way too much money on bulk. Yeah and we go through the order of flow. So we start with a
fixed speed compressor. It takes in our atmospheric air, compresses it about 125 psi and then from
there. So well yeah the nitrogen is or atmosphere is like 70% nitrogen right? The air that we breathe
is 78% nitrogen. So it's kind of free. Free nitrogen everywhere. Exactly. Yeah so all we're
doing is just grabbing the free air that's there and then sucking in the compressor and it's a
fixed speed compressor. So you think of like a supercharger right? There's two screws in there
and that compresses the air. So these two screws are constantly running while it's loaded.
But that's getting into about 125 psi and then we're going into a compressed air tank, that large
tank. Yeah and that just helps with like buffer tank. Yeah you can think of like a buffer tank.
It just it gives the compressor a chance to take a break. So it's going to bounce between a pressure
set point and that buffer tank helps give it a break. And as our demand changes and there's
because there's a ton of variables. Yep exactly. And then out of the compressed air tank it goes
through a refrigerated air dryer. So at Liberty what we do is we oversize these refrigerated air
dryers. So we use a cycling type refrigerated air dryer. The reason we do that is if you tuck this
system in the corner of a shop in the summer months it gets really hot. Once you start getting
to about 90 to 100 degree ambient temperature you dramatically de-rate how much air you can dry.
So understanding that we sell these systems all over the United States, Canada and Mexico. We want
to make sure that we have a standard system that's always drying that air too. So it's a little unique
compared to others but we want to make sure that we protect your investment. Well I was going to
say in Nevada we have no concept of humidity. It's incredibly dry. We use a lot of lotion.
So our air dryers they're putting out like a little trickle of water. When we visit our
Kentucky facility it's like a river coming out. You're completely shocked and surprised at how
much how much moisture is in the air. Absolutely critical to get all that moisture out of the air
before it goes to the next steps. Yeah one of the worst things for a generator is water and oil.
So we want to make sure that we have good drains, good filters, we're releasing all of that.
So yeah we have the first line of defense 90% of the water knocks out and then it goes into an oil
miscellanator. So you're not going to see that in many of our competitors systems. The reason we put
it in is we try to learn from our mistakes. We've had a compressor dump oil and we understand that
cost and damage to the laser. It dumps it into really expensive filters and then really expensive
lasers. Yeah so it doesn't add more cost to the system absolutely. But we were talking about
redundancy, building value into the system and fail-safes. I always say like you're going to
spend money. Do you want to spend it now or do you want to spend it later? And usually if you can
spend the money now you don't have to spend it later because adding protections like the miss
separator it prevents you from spending a bunch of money on optics and downtime and everything else.
Yeah so that's purely a fail-safe. It's designed to get hit with bulk oil so there's big filters
in there. So out of that we're somewhat dry. We're not really that clean so we go through a
four-stage filtration. All those little filters? Yep so we knock out the water, particulate and
vapor. So by the time we got out of those filters we're somewhat dry. We're really clean at this
point. So we want to send that into the nitrogen module to start making nitrogen. So what we do is
after it's dry it goes into the bottom of the nitrogen modules. And in these modules there's
little beads. So if you think of like a sponge it's porous. A nitrogen molecule is bigger than
an oxygen molecule. So under pressure when we feed that bottom of the module the oxygen beads
get sucked into that sponge. It's called carbon molecular sieve or CMS. So under pressure the
oxygen gets sucked into these beads and the nitrogen passes by. And then we store that.
It's kind of like a water softener? I guess yeah. The beads and you put the salt in there to
recharge the beads or whatever. But they also purge. It sucks up the oxygen.
Actually it's doing it right now. That was good. That was good timing. So there's two columns. So I
could back up. So one column is going to feed for 60 seconds. After 60 seconds it's so saturated it
can't absorb oxygen anymore. So what we have to do is release that back to the atmosphere. So what
you're going to hear is every 60 seconds the column's purging and fluctuating back and forth.
And that way the beads don't really need to be changed for a long time?
That's why it's so critical to supply the beads with really clean dry air. Because if you get
those beads wet, think of like mud or like dirt. You get it wet and it turns to mud. I can't absorb
oxygen anymore. So that's why it's really critical. One thing that's unique about us is we use nitrogen
modules versus twin towers. Basically what that means is we can pack our sieve, that carbon
sieve, a lot tighter. So when air hits the bottom, we want to be able to absorb all that oxygen. If
you have a loose fill, think of like air channels that can happen. And also if that's a loose fill,
think about every 60 seconds, 120 psi, slamming that sieve up against the top and coming back
down. If I have a loose fill, think of like a bag of potato chips. They're full size chips and you
crunch that bag and now you have dust. Same thing with those beads. Once it turns to dust, I can't
absorb oxygen. So in like twin tower systems, you might get three, five, maybe seven year lifespan.
You're going to go over 15 year lifespan with our modules just because we pack that sieve so tight.
That's what we've noticed. I mean, we've been running your systems incredibly hard, 24 hours a
day for years and years and years. And we've never had to repack those things or whatever.
You guys are also great on doing your maintenance.
We're really good at maintenance. Shout out to our entire maintenance team. But like I said,
you're going to spend money no matter what. You can either spend it the right way or you can spend
it the very, very painful way much later during like emergency tear downs. And then you have
downtime and all this other stuff. So just buy the good ----.
Yeah. So after we have the stored nitrogen, good purity.
Okay. So yeah, it's been compressed. It's been chilled. It's been filtered. And then we get the
oxygen out of the equation. Then we're putting it in the booster, right?
Oh, not yet. So we don't want to just go from the nitrogen module to the booster. So we're
going to suck all that volume out of the nitrogen modules too quick.
Okay. So what we want to have is a good stable purity.
So in those tanks, we have about 100 PSI of your 99.5% purity of nitrogen.
And we can go any purity you want. It's just based on where you're cutting those fit your needs.
Okay. Yeah. Actually. So that's when you order a system from these guys,
they're going to figure out like, hey, are you medical or are you aerospace?
Do you have to have five nines of purity or whatever? In our case, we kind of shoot for the
general, you know, whatever tolerance, the lower the purity, like the more volume you can get.
Right. Is that kind of true or am I just making it?
Kind of. Like, so for instance, in just one nitrogen module,
if I lower the purity, I can get more flow out of it. Right. But there's also like a counter
effect to that too. I might need more compressed air. Right. So yeah, you can tweak it a little
bit. Yeah. And then it's going to affect your edge quality. Like, well, this is a piece of
stainless that I have, but it's damn smooth. Yeah. Check that out, Logan. Good luck. Good
luck. As you lower purity, your edge is going to start to color. You're going to get like a
straw gold or a brown or purple or whatever. If your purity is low. But if you buy a system like
this that can constantly purge and whatever, you can end up having like 99.5 with a decent flow
rate. Yeah. They're all going to have decent flow rate. Exactly what you guys need. But it
really comes down to your needs. So like when I'm first talking to an owner like you, I want to know
are you welding after you cut? Are you painting? So why would I buy this really big high purity
nitrogen generator if I'm just welding over that cut? Right. So who cares if it's shiny silver
anymore? Now, if I have a perforated hole that's showing on my finished piece, maybe. Yeah. I will
say on welding, sometimes if you spend a little bit more money on the purity, it makes your pre-weld
processing much, much faster too. So because actually a lot of our customers will write in
and be like, dude, I didn't have to do anything. I just welded it and it was perfect. Didn't hit
it with a grinder. And that's at 99.5. Yeah. So yeah. Okay. Yeah. Yeah. So after we separate the
oxygen from the nitrogen stored in that tank, we have good volume, steady purity. Then it goes into
a booster compressor and we like to use piston style boosters. It's more efficient at higher
pressures. In the industry, you got oil free versus oil injected. It's like, do we use oil?
Do we not? We want to protect the laser. When Liberty first started, we did oil free because
that's the first thing that we thought we're diving into laser industry for generators.
We don't want any oil. What we found is that these oil-free boosters are very costly to maintain.
They are. You have to rebuild the whole entire pistons. There's piston rings that you have to
put on them. When they go down, they go down hard. Yeah. They go down. So it's labor intense. It's
very expensive. So what we found is, okay, lubrications are better, having lubrications
much better, but you have to filter it out. So any of the filters that we have, Jim, they're all
very, very high efficiency filters. So if you think of like, if you go get a filter from the
Home Depot, it's going to be low efficiency. And if you just think of like the filter, like a fence,
it's just tight, more tightly woven. So I can stop more particulates. So after the booster
takes that a hundred PSI of nitrogen, it builds it up to about 400 to 430 PSI.
Which is what we need to use in the lasers. Yeah. Yeah. I would say most lasers,
pressures are starting to come down. But what I've always seen is if we stay 400 PSI at the
laser, we're good. Yeah. So we just don't want to fall below that. So that booster is going to
operate around 400 PSI to 430 PSI, right? So as you, if the booster fills up to that high pressure
tank, 430 PSI, your lasers are pulling, that pressure drops down to 400, the booster turns
back on. So the booster doesn't hold pressure. It just builds pressure. Yeah. It's not running
all the time. And you will notice when it's running, that's probably the loudest part
of the entire system. The main, like the Kaser compressors are super quiet. They're great. They
put out a ton of heat though, like comical amount of heat. So you want to make sure they're ducted
really well. Noise isn't really a big issue. We've had these systems in what, five different
buildings now, six different buildings. But we knew from day one, the first thing that we wanted
to mitigate is noise. Like we run a pretty clean shop, pretty quiet. We don't like to have ear
shots. So one of the first things that we did is dedicate a room to it. Like, even though it was a
small system, we dedicated a room. And the main reason to do that was to duct out all the heat.
And then also to keep the noise of the booster pump down a little bit. So that was another thing
that I was going to say to anyone watching this, who's considering, you know, Liberty Systems,
you do need some square footage. And like, if you get the CAD model for all these things,
you can jam them together. And you're like, oh man, I can fit it in a 10 by 10 room.
You have to remember maintenance and the maintenance guys will lose their mind if they
can't, you know, some of the maintenance guys are bigger too. So they can't squish through,
you know, really tight stuff. You have to take panels off, you have to take doors off. So
consider the square footage. That was one of our challenges. Yeah. Well, that's one thing too,
like all the sales engineers at Liberty Systems know how to use CAD. We work with our engineering
team. I actually like using CAD. So it's fun for me to play Tetris is what I call it. So you tell
me your square foot that you have, and I'm going to try to move it around or say, hey, Jim, we need
a little more space. I think, well, Matt's not going to want me to say this, but I think we're
a little tighter than their recommendations just because we had some constraints, but it still
works. You can take every panel off. You have access to everywhere. You can get a big wrench
in for the hose. You can change oil. I will tell you the first system that we built, we realized
we couldn't change the oil at one point. So we had to get some forklifts involved. So yeah,
space is a consideration. Heat is a consideration, but it's just pencil it in as part of the system.
Just work with your HVAC guy to build some ducts. At one of our shops, we had a duct,
actually on this one too. We can either duct to atmosphere or we can duct to heating in the
winter. I mean, that's really smart. Like you said, they produce a lot of heat, a little bit of air,
but that's the technology we have to make compressed air. So if you have all that heat,
why not during the summer, I mean the winter, bring it back into your building and save on
your energy bill? Yeah. Texas, I think it just goes outside all the time. It's always hot in Texas.
Holy crap. What else do we need to know about this? I would just say, like you talked about
space, but it's nice because I can still open up the doors and just think about like the system
being able to breathe, right? We don't want this system to get too hot. So I always say if you can
stay between 45 degrees Fahrenheit to 110 degrees, stay in that optimal range. But at Liberty, what
we would do is work with you, right? Do we need more vents in the walls? So there's a lot of times
I help customers build these rooms too. Now we're not doing the subcontracting, but I'll help lay
out the spacing. It's more than the equipment. It's the entire ecosystem. It's the room. It's
the environment. It's everything. Like you said, the system does breathe. If you think about all
of this air that we're pulling from atmosphere, it has to come into the building too. So sometimes
you need an inlet and an outlet and people don't think about that. Sometimes you need like a four
foot by four foot, you know, inlet just to feed, you know, how much is coming in. And then sometimes
you need to condition the facility. Yeah. So let's just say it is too hot. Yeah. You might need to do
some type of AC unit or big fans. Like you guys have industrial fans. Yeah. So like we're in
Nevada, our summers will get 100, 105. We've never had any problems with this room and it's
because we did really smart ducting with the big compressors. And then we're just pumping a lot of
air through this building all the time. We will rarely get an over temp alarm. Yeah. And then,
so we talked about spacing and then I just, I just really want to hit it again, redundancy. I
just try to say that to everyone. Our standard compressed air tanks now come with two inlets.
So we understand redundancy is so important that either you get a backup compressor from us or you
tie in your shop here, but no matter what, if you ever see a system from us and you see two inlets
at the compressed air tank, that means we want you guys to supply more air. Yeah. That's, that's what
we do. So we have our main compressor that's doing the bulk of the work, but if we need to take that
offline, there's a couple of valves that, that we can turn. Yeah. Cause we also have another,
what, 200 horsepower of compression in the building that we can tie into. Yeah. This thing
we can turn on if we need to. You have so much equipment. Backups on backups. Yeah. And you'll see
valves throughout the whole system. I know it might look a little crazy, but I come from the service
side too. And it's so much easier to work on a piece of equipment to be able to isolate that
specific component and work on it rather than having to drain the whole entire system,
build it back to purity. So if you see our systems and there's valves all over the place,
there's a reason for it. It's so that we can get you up and running quicker or do maintenance faster,
help troubleshoot things like that. So like in the old days, when we were a smaller shop,
when we only had two lasers we would usually be able to shut down the system and then just run
on a 450 liter Dewar. Yeah. You know, and when we didn't even have like the big bulk tanks or
whatever, we just run on a Dewar for a little bit, a few hours or whatever to do maintenance,
fire it back up. We had no downtime. The laser operators, usually our goal is so that they never
know when we're doing maintenance. They should just be able to do their job. I guess one last
thing that it's really nice about these Nitro modules too is, let's just say you knew you're
going to have this growth from the beginning, right? We can size these systems for future
expansion. So if you came to me and you said, Hey Matt, I'm getting two lasers today, but I
know I'm going to buy two to three more in the next five years. We can size the system for future
expansion. We would oversize the air compressor, the booster, all of the other components,
but the Nitro modules are just going to produce enough Nitrogen for those two lasers. In the
future, you add another laser, you can just drop in another Nitro module and a buffer tank and
another one, another one for however big we made it. Well, I was going to say, we've upgraded this
system a couple of times now, but that's our old buffer tank, right? Yeah. We never got a new one
from you guys. Yeah. We also have another buffer tank over there that we've used forever. So it is,
it is modular and you guys are really smart, you know, as the years go by, as demand changes,
as technology changes, you know, you look at it holistically and you're like, Hey, keep this,
keep this. Yeah. We're going to replace that and save, save some money over the long run.
Anyway, thank you for watching behind the scenes with one of our preferred partners,
Liberty Systems. If you have any other questions, hit up Matt.
