This Ugly Homemade Desk Had a Lead Secret

Trash To Treasure
3 followers
Jul 25, 2026
This piece was a challenge, alright. I had issues with the humidity and my paint and topcoat drying, found lead paint on the drawer, which I opted to remove in case an owner down the road tried to sand it off not knowing it was lead (due diligence).
In the end.. I'm not sure if I ended up with a swan... more like a fancy chicken, but I'm happy that it's saved from a landfill and has a new life. I could totally see this in a teen's bedroom for some reason! I wasn't super happy with the two-tone paint, but after all the headache of doing this flip, I was not repainting it. Haha. And it's one of those things where the more I look at it, the more I do like it. :-)
AI Generated·May contain errors
Well, here I am again with another crazy challenge.
I might have bitten off a bit more than I can chew with this one.
This desk was free and has been in my storage room for about a year.
It's actually kind of funny.
The classified ad where I found it literally only said,
free, just come get it and don't look back.
That's all it said in the ad.
So of course I had to go get it.
The mahogany veneer on the top is shot and full of holes.
I don't know what's going on with the sides.
I don't know if this is a homemade piece.
I just know that I have got my work cut out for me.
But that said, this is the perfect piece for the ugly duckling challenge.
The mission is simple.
Find the ugliest piece of furniture you can and try to save it.
That's pretty much what I do on a normal day anyway,
but I don't know.
This one's gonna be interesting.
My name is Angie and I refinish furniture.
Sometimes I paint and sometimes I don't,
but I always do what I can to save old pieces from the trash.
Welcome to my workroom.
This fun challenge is hosted by Kori from Desert DIY.
If you haven't checked out her channel yet, I will pop a link down below.
You definitely want to check this girl out.
She's amazing.
I just want to say a big thank you to her for allowing me
and all the other participants to join her in this challenge.
Okay, so let's have a look at what we're dealing with.
You can see here that the veneer on top is really rough.
There are so many finish issues.
There are holes, scrapes, scratches, stains, discolorations,
and I don't know if there ever was veneer on the sides or what the heck happened here,
but I am not loving these plywood drawers and sides.
There are legs to the piece, which I'll be refinishing.
I don't know why this bottom drawer is painted multiple colors.
This is very confusing to me.
I'm thinking this is probably a homemade piece,
but even so, I want to do what I can to try to save this.
This is literally the last stop for this desk.
This is the last chance right here.
I might try to reuse this hardware.
I'm not sure yet, but I'm going to set it aside for now.
I really wanted to take this back piece off.
I could see that it was nailed down,
but pretty much right away I was able to tell that it was also glued down,
so that's not coming off.
So instead, moving forward, and I'm just going to be applying
my favorite stripper all over the piece,
and I already know this is going to be extremely difficult to scrape off.
There are so many chunks and holes missing from the veneer.
I have to be super careful while I'm scraping this off afterwards.
So that worked for about a half an hour,
and on to scraping here, and right off the bat,
you can see here I dug up a little chunk,
and I knew that was going to happen.
Normally, you want to try to save as much of the veneer as possible
by gluing it back down.
There are too many little chunks and pieces.
I think in this case, for me, it's just going to be easier
if I just pull those little pieces off
and try to fill it with the filler when I get to that point.
So for now, I'm just trying to scrape around the pieces as best as I can.
Sometimes I go backwards a little bit or sideways, whatever I have to do.
I absolutely could have painted the top or replaced the veneer,
but I was determined and I wanted to see if I could save this.
Starting off with a 150 grit sand pad,
I don't really want to do anything harsher than that,
so I need to sort of err on the side of caution here.
You can see just below the sander there, there is a little ring.
There is a lot of staining and discoloration on here.
I'm not sure how much is going to come out with sanding alone.
I'll find out soon enough, but at this point,
I'm not 100% sure if I'm going to be just doing a clear coat on this
or if I'm going to have to stain.
Doing just a clear coat over top of wood filler is a bit tricky
because you have to have the color of the wood filler
matched almost perfectly with the color of the wood after coating it.
It's a little bit complicated to get there.
I'm actually going to be mixing two types of lippage wood filler here.
I didn't have quite enough sanding dust from the top of this
to sort of make my own filler,
so I'm mixing a little bit of the teak filler with the mahogany filler
and hopefully the color will be close.
I do already know though that I will have to do
some sort of touch-up to try to help it blend in a little bit.
Right now, the wood filler looks darker than the wood grain itself,
but once there is a coating on this of some sort,
the filler is going to be lighter than the wood tone,
and that's something that you kind of need to know
when you're trying to fill wood like this.
Okay, so this is Bondo, and I've used Bondo several times in the past,
but only for small fills.
I've never done a huge portion like this,
and I'm going to tell you right now,
I used way too much of the cream hardener,
which is the red stuff, way too much,
and it got away from me a little bit.
You do have to work super fast with Bondo.
Usually you get anywhere between three and five minutes of work time,
and then it is hard as a rock,
and that's exactly what happened,
except I got about two minutes before I couldn't scoop it out anymore,
so I ended up wasting a lot,
which was a huge bummer,
but the reason I'm putting Bondo on the sides
is because it's hard to tell here,
but the wood is actually quite uneven.
There's like ripples and dings and holes.
Now, I do have a wide Bondo spatula,
for lack of a better term.
Do you suppose I could find it?
No, so here I am using a putty knife,
and you can see right there,
that is when it started to go hard on me,
so I had to mix up more,
and I used a lot less of the cream hardener.
And that's so much better,
and you can see the color difference.
That second color is more what you're looking for when you're mixing this.
If you're unfamiliar with this stuff,
Bondo is what they use to fill holes and scrapes and stuff in cars,
like auto body work,
and a lot of us furniture refinishers like to use it in place of missing wood,
or if we're trying to even out a surface that we're going to be painting,
which is exactly what I'm using it for here.
It's pretty strong smelling,
so you want to make sure you're in a well-ventilated area,
and a respirator is always a good idea,
and I use gloves when I'm handling Bondo,
and you especially want to have some sort of a mask on when you're sanding in this stuff.
So after the Bondo mixing fiasco,
here is problem number two.
I was just about to start sanding this,
and I had a feeling.
I have a lead test kit,
I use it on older paint all the time,
and there was something about this color and the sheen of it,
I had to check,
and sure enough, this is lead paint.
I decided to set the drawer aside for now,
and move on to sanding this off.
Bondo dries extremely hard,
so you want to try when you're troweling it on,
to not have too many sort of peaks and valleys,
because it is going to be harder to sand.
I'm sanding first here with a 100 grit,
which is fairly coarse.
I'm just going to flatten it out.
After that, I moved up, I believe, to a 150,
or no, sorry, it was 180.
And super smooth now.
For the second round of sanding here on the top,
I'm using a 220,
and I'm especially careful here around the edges
where the outer solid wood trim meets the veneer.
That is a prime location for burning through veneer.
I see it all the time.
So take your time,
turn your sander down if it's a variable speed,
or just use less pressure
when you're doing those delicate areas.
I always like to do a slightly rounded edge
when you have trim like this,
otherwise it tends to chip away
and be kind of nasty looking over time.
So I find just slightly rounding it
is going to make it hold up a lot better over time.
Now that everything's sanded,
I need to see what this top would look like
if I were to apply a clear coat.
I already know the mahogany is going to be super dark,
because that's just mahogany.
But the trim on the outside,
I had a feeling would be a little bit lighter.
And I also want to see if any of those stains
and discolorations come through here.
Adding the mineral spirits
will also help me color match these filled areas.
Now the marker I'm using here,
you can see obviously it's a lot darker,
but the filler is going to absorb this color
and it won't be quite as intense once it dries.
I knew going into this project
that it wasn't going to be perfect.
It's not the typical sort of thing I work on,
so I had to sort of mentally prepare myself
for the fact that this might not turn out
exactly as I would like it to turn out,
just because of the severity of what I'm dealing with.
These spots do blend in better now,
but the gel stain will help even more.
And now to deal with this paint.
So what is the big deal with lead anyway?
Lead is actually a pretty serious systemic poison.
The amount on this drawer probably isn't that bad.
Most of the time when you hear about lead poisoning,
you're talking about sustained exposure to it.
Some of the health problems lead can cause are anemia,
serious headaches, nerve damage, kidney damage,
brain and nervous system damage, among other things.
Right, so you've tested, you've got lead.
How do you get rid of it?
There are some key points.
First of all, you don't ever want to dry sand it.
You want to somehow remove it while keeping it wet.
It's when those particles become dust and go airborne,
that's when it's the most serious.
You can see here that not that much is coming off,
and it's because, like I said, the wood is very uneven.
So once I scrape this first layer,
I'm going to need to apply more stripper and do this again.
Second thing that's very important is to protect yourself
while you're removing it.
You want to be wearing a proper filtered mask.
Eye protection is a good idea.
Definitely be wearing gloves.
To actually remove it, you want to strip or wet sand it.
Now, if you're talking about lead paint on walls in a house
or, you know, big doors and trim, stuff like that,
you might want to look into a proper lead abatement company
just to ensure that it's proper removal
because not only is there the removal of it,
you also have to dispose of everything properly
and basically consider that everything that this touches
is now considered contaminated.
So these gloves get thrown into...
You see my little bucket there?
That is where I normally scrape all my stripper
and about once a month or so,
I take it to the hazardous waste disposal site.
Long story short, the issue with lead is not that it's in the paint.
Like, if you touch it, you're not going to get sick.
It's when that paint starts to chip or flake or become dust somehow,
that's when it's dangerous.
So just keep that in mind.
I'm keeping these legs wood grain.
They're going to be stained along with the top
and these metal caps for the feet,
I'm going to be spray painting.
They're a little bit too far gone to just polish up,
so I'm just giving it a quick light sand
just to help the paint adhere
and I'll be spraying those shortly.
I'm going to be priming this piece prior to painting it,
so I'm just trying to remove any residual bondo dust
that might be around.
Usually I use the bin primer in the can
that you can actually roll on.
I don't have any of that at the moment,
but I do have some white spray primer left,
so I'm going to be using that for this piece.
What's really funny about this point in the project
as I'm sitting here thinking,
I still don't know what color I'm going to do this yet,
so I figure I will stain the legs and the top
and then go from there once I find out
what sort of color I'm dealing with
after everything is all stained.
I'm using the same color on the top that I did on the legs
and that is General Finishes Gel Stain
in the color Antique Walnut.
The reason I am opting to stain this
is mainly because of the little filled and patched areas
and because the mahogany is a different type of wood
than the trimmer on the outside
and I want the two colors to sort of blend a little bit better.
I don't want them to be such a contrast.
Not bad for a desk that was supposed to be thrown out.
I'm quite happy with how this top is turning out.
It's not perfect, like I said,
but it is a far cry from what I started with.
So here I'm thinking I might try a two-tone look.
I don't know what struck me to do this.
It's not something I normally do
but I thought I would try it with this piece.
So what I want to do is have the top
approximately the top third one color
and then the bottom two-thirds another color.
And these are the two colors I'm thinking.
They're both custom mix colors.
This one I'm thinking for the top
and this sort of deep navy charcoal grayish for the bottom.
Sorry, I just had to add those guys in.
Aren't they the cutest?
They are in my office, which is where I do my editing.
They're right behind me at this very moment
and it's extremely hard to concentrate.
However, back to business.
So as you can see here, I'm choosing to use a wipe-on poly.
Wipe-on poly is a surface top coat,
meaning it doesn't really soak into the wood.
It's usually pretty beginner friendly.
Unfortunately for me in this case,
this was kind of the beginning of the end for me.
I live in Nova Scotia and I live in the valley in Nova Scotia
and we're notorious for having hot humid summers
and today was no exception.
But to make things worse,
there is the remnants of a hurricane coming up the coast
and it's pushing a ton of hot humid air my way
and nothing is drying.
My paint is taking four or five times longer than normal.
Instead of being dry to the touch in 20 minutes,
it's taking three or four hours
and even then it's not setting up right.
There's weird ridges.
Normally I can get a very smooth finish.
In terms of the poly, it just wouldn't set up.
So after very patiently waiting for almost 11 hours
for the first coat of poly to dry, I took it off.
I used some mineral spirits.
I stripped everything back.
I basically had to start over.
Now I probably should have just started with this product to begin with
because it's doing a fantastic job.
This is Odie's Wood Butter
and it's a bit of a combination between the Odie's Universal Oil,
which you've seen me use many times,
and Odie's Wax.
It's kind of right in the middle.
It applies pretty much the same as the Odie's Universal Oil.
You basically use one of these little Merck and Merlon pads to apply it.
I believe this one you leave for about 45 minutes or so
and then you buff it off.
Odie's is very natural.
It smells amazing.
You can see I don't have to wear gloves while applying it
and I should have just started with this to begin with.
Now there's a bit that I didn't include in this video
and it's basically just multiple coats of paint
and struggling through that with the humidity.
Things like putting the hardware back on and the legs
and in this case I'm opting not to show you that part
because I want there to be some sort of some element of surprise at the end.
So the question really becomes,
did I turn this ugly duckling into a swan?
Swan is a stretch but it is a hundred times better
and even though this didn't turn out at all how I expected
and it was very difficult,
I am happy with it
and I'm glad to be able to save another piece from a landfill.
