Making Moccasins 1 - Sewing the Toe

Native American Crafts
28 followers
AI Generated·May contain errors
So at this point in our moccasin making you should have finished your vamp or
toe piece with all of your beading and it should look something like this. You'll
probably have some extra paper sticking out over the sides. I just removed, as you
can see here with all these little bits of thread, I just removed the four darts
that we put in the four corners to hold everything in place while we were
beading. So now that those are out you can take your scissors and just cut
around your design so any excess paper like this comes off and you just want to
make sure that nothing's showing outside of the felt that we've used for our vamp.
Making sure that you don't actually cut the vamp because that would change the
size of your moccasin and that would not be ideal. It doesn't have to be perfect
this is going to be in between the outer layer of your moccasin and the
lining that we're going to make in a little bit so so long as there's no rough
edges or nothing poking out further than the vamp itself. It could look something
like that and then if it's very close to the edge like mine is it might actually
end up getting sewn into the leather once we start doing our darts to hold
everything together but that's totally okay. So then this gets pushed off to the
side and we will move on to our next step. For this next step you're going to
want to make sure that you have a couple things on hand just in case. I like to
have a pair of scissors, a ruler just to make sure that once you start attaching
your vamp to the bottom leather piece that we would have cut out earlier that
you're attaching it in the right place so that it'll fit your foot and you'll
have enough leather to make the heel. We made these little thimbles out of the
excess leather and because we're working with buffalo hide which is quite thick
much thicker than the leather that we're using for our welts which is deer as you
can see it's much thinner than this piece. So we took an extra little
rectangle of the buffalo hide and you can see I kind of just folded it into a
cone and sewed up along this one corner so that it's doubled up in this area to
make it a little bit thicker so as you're trying to sew through the leather
your needle isn't going to go into your finger it'll get stuck in the leather
instead. You're also going to want to make sure that you have your thick thread in
the brown that we chose to match our leather and you're going to want to make
sure that you have your Glovers needle which I just had stuck in a little piece
of extra felt. These are special because they're flat on one side so it makes
them much easier to get through the leather. I'm not sure yet you can kind of
see that a little bit there. It makes them much easier to get through the leather and
then I like to have a seam ripper on hand because I often have to redo things and it
makes things much easier. But because that's sharp I'm going to put that away for now.
So our first step is going to be to measure our piece of leather which I'll
show you momentarily. Alright so for our next step we're going to begin stitching
our vamp and our welt and our base piece together. That's going to make the soul of
our moccasins. So I've decided that I want the rough side out so I'm going to face that up
because you want generally the same as most sewing. You want the good sides together and
to do this first step you want to find the center line of both your welt, your soul,
which is right there, and your vamp. So because the beading it's a little bit stiff so I'll fold
it that way. Find dead center and put them all together with the welt in between the vamp and
the soul. So that's my center line right there. Now I've already threaded my Glover's needle so
that it's ready to go and I'm just going to tie my knot. And for some of you I'm going to show
you a neat trick. If you get the end of your thread, now I've doubled my thread you don't
have to do that at this point. I don't know if you can see that. You don't have to do that at
this point but I prefer sewing with doubled thread and it'll make it nice and strong. So
that's what I've decided to do. But if you hold the end of the thread with the hand that's holding
the needle, okay, and then you wrap just above that a few times and then grab all of that. Make
sure that you don't do what I just did and you keep all of your thread centered. So there you
grab all of that and pull the thread. You hold on to the needle with your free hand and you pull all
the thread that you just wrapped all the way down. It should, if you've done it correctly, give
you a wicked little knot at the end of your thread. I don't know if you can see that but there you go.
So now you can start sewing. You want to grab all of these making sure that they're still in the
center and start from the back. Push up and this is where your thimble will come in handy. So I've
got my thimble on because you're pushing through two layers of leather and the felt. So you want
to make sure that you're getting relatively close to the top there. Push through and pull. And what
I like to do, part of the reason why I like to sew with my thread doubled over, is because then to
make it extra secure I can go in between the threads that are knotted at the end and that
will make it nice and tight. Now for this and for all of the subsequent steps you want to make sure
that all of your needlework and all of your thread is being pulled very tight as you go along so that
your moccasins will stay secure and that you won't have any holes in your finished product. So I'm
gonna go through, you want to go through about I'm gonna say three or four times. These are kind of
tacks you're gonna be sewing over them afterwards but still just to make sure that you have a nice
base you want to keep them nice and tight and you can even go back and do a little loop under the
thread that you've just sewn through. Again to make it really really tight and secure. Take my
needle go back again and I'll do that one more time once I get this through. And because we are
using buffalo hide it's quite thick so sometimes you might need to play around with your needle a
little bit to get it through. Make sure that you're not sewing around your welt as I've just
done. Oh and I'm still doing, there you go. So pull that again super tight and that should be fine. So
I'm gonna go to tie this off, loop under the thread that I've just gone through, pull it through and
then go back again. See this is the loop that we've just made. You're going to go through that
loop and pull that tight. And so that looping around itself is how you tie off most stitches
in sewing. So you're gonna go ahead and trim that and there you are. That's your first dart that will
hold all of these pieces together. Your welt is in there nice and secure, your vamp is facing the side
that you want facing out. So my moccasins are gonna be this suede finish on the outside and
then this just like the animal would have been, like the fur on the outside and the smooth side
on the inside. Supposedly this way helps with ventilation, I'm not sure. Somebody else can
probably tell you more about that. And we're gonna move on to our next step. Okay in this step we're
gonna be putting in our next two darts. But before that just to make sure that we have enough space
I'm gonna show you what you kind of want to watch out for. So because this is going to be your sew
and this part is gonna come up to be your toe and this is gonna fold in to be the heel of the
moccasin, you want to make sure that when you're doing these darts you leave enough space. So hello
foot, it's a little bit dark but that's okay this is just for demonstration purposes. You want to
make sure that behind your heel you have at least three centimeters because that's what you need to
do your heel. A little bit more than that is generally good because a little bit of excess is
never a bad thing. So behind my heel here I've got just over four centimeters and I'm probably gonna
keep it like that. So to do your next couple darts you're gonna want to pull this back and so you'll
see how this will come up to make the toe of my moccasin. And you're going to, I'll mark this off
just with a little mark from my thing here, so you're going to pull this up and that is essentially
where you're going to do your next dart. So all of this excess is what's going to be gathered and
give you that ruched look at the front of the moccasin. So here your welt is going to come
around and you're going to want it to be right at the edge of your vamp so that they run parallel
and bring this up, that's going to sit right there. Generally it's about halfway down the
sole that you're doing your next dart but I'm just gonna take a little piece like that so that
I can see exactly where I've made that. So that mark is right there, quite faint on camera but I
can see it here. So when I remove my foot I know that I'm going to gather one centimeter up from
the corner of our vamp with this little mark that I've made here, again making sure that our welt
is running right along the side of the vamp. So gather it here and we're going to do the exact
same stitching that we did for this dart at the front here and we're going to do this on both
sides. Okay, so after putting in those two darts your moccasin should look something like this
weird thing. As you can see it's starting to take the general shape of what it's going to look like,
your toe is going to come up something like this and all of this is going to be gathered
and this back part is just enough that it can be pulled around maybe with a little bit of excess
to make the heel. So that's ideally what you want it to look like at this point. The next step
you're going to again get your welt so that it's up against your vamp and everything is all lined
up and you are going to find, it doesn't have to be perfect because like I said before this is all
going to be gathered in that kind of ruched look, so you're going to get those together, find what
you think is the center and do the same type of darting as you did here and here in the center
of this area. You're going to keep going until it gathers a little bit and then eventually you're
going to do a whip stitch to just gather the material in between those midpoint tacks. If that
doesn't make sense just keep watching and we'll get there together. However I am going to be doing
something slightly different, the same technique but in a different place because my leather is
very long and narrow and my feet are very long and narrow. I'm going to gather slightly further
down than half and I'm going to keep this part relatively flat against the moccasin and do a
running stitch instead so that most of the gathering is right on the toe. This might not
work out, I might have to take it out which is why I have my handy dandy seam ripper but if it does
work out then that's why this might look a little bit different than what some of the written
instructions in the moccasin binder say in the OEE room. If you want to continue on the traditional
way, the way that it's been done for the last few years with the pars, find the midpoint
and do your next couple tacks and we should be in relatively the same spot in the next video
and I'll explain how to carry on from there. Okay so like I said I'm doing mine a little bit
differently than the instructions have said for the last few years in the par book but what
you would have done, this connection would have been around the same area on the welt but it would
have been gathered in the center so that all this excess fabric would have been split up
between this section and this section and then like I said before what you're going to do next
and you would do this both up here and down here because you'd have more excess fabric on this side
is you're going to find the center again bring that in and you're going to do more darts and you
would do one two three four and then you would gather that again in between those until you get
pieces that you're comfortable whip stitching around and a whip stitch is when you go through
the fabric loop around to the same side that you went in initially so say I'm going to be doing a
running stitch along here is when you just go back and forth sorry um I'm just going to be
doing a running stitch along here so I'm going to be back and forth in the fabric but if you were
doing a whip stitch say you started on this side you go through and then come around and you're
going traveling along the edge but you're still always going through the same side so you're
going in the outside pulling through going in the outside pulling through etc so once you do
you gather the welt and do your
tack in the center and then you do that again you could even do another tack in between there and
then once you're comfortable doing whip stitch around that then you would go from your initial
tack whip stitch all the way around until you've gathered and secured all of the fabric so that
don't have any holes okay I will reconvene with you after those steps okay so once you get to this
point I've done a lot of tacking because I didn't do any gathering along here there was a lot of
extra fabric up at the top so I did perhaps a little bit more than you would have done but
it's the same idea so it should look something like that and once you get to this point you can
start doing your whip stitch I haven't done my sides here yet because I'm going to do the same
thing that you'll be doing on your moccasins so I've already knotted my thread I'm probably going
to need to cut another length I'm not sure if this will be quite enough to make it all the way around
but we'll see hopefully it will be so you want to start from one end I generally go in right around
where your first knot is you want to go through with a lot of effort this is why we have our
wonderful little thimble you can see how many times it's gone through into my finger
and pull that through again because you're going through so many layers and thread and whatnot
it might take a little bit of working I'm going to secure it by going back through
my thread please focus camera there we go pull it tight and then you're basically just going
you can you can make these gathered parts smaller if you want or you can just tighten them across
it's totally up to you depending on what you will you want your moccasins to look like
I'm probably going to do a combination of both because these gathered pieces are fairly uniform
right now and I think I might want them to look a little bit more randomized but you're basically
just going so I went through and I'm going back around that's what a whip stitch is so you're
always going to be coming through from the same side so pull that tight and then go back around
I'll come in from this side again once you loop through you want to be pulling these stitches as
tight as possible I'm going to go through the center because these are going to be essentially
everything that's holding your toe together so if you're especially once you get around to the
very I see and then I've created two nice little gathered bits right there especially once you get
around to this toe area if your moccasins are tight at all on your foot the leather will stretch but
all of this especially because we used felt for the vamp you want those really tight so that
eventually your toes don't pull it apart okay so keep going around like that until you get to the
other side all right so at this point you will have if you've done the method that's outlined
in the written directions you would have done that whip stitch all the way around
if you've watched the video and this end up ends up looking really nice so you've decided to do
what I'm doing right now then I started from here and did my whip stitch all the way around I did
tie it off however because I had so much thread left I figured I'd leave it and just continue
going across with my running stitch and actually instead of doing a regular running stitch with
which you go back and forth through the fabric I'm going to do a back stitch which I'll show
you right now so my thread is coming out over here as you can see maybe once my camera focuses
beautiful so I'm going to go through all three layers the leather the sole the welt and the vamp
and then instead of going instead of continuing forward I'm going to go back this way parallel
to where I went in originally this is very dark okay parallel to where I went in originally
back through my needle is also a little bent because it was a little tough going back through
those original stitches those tacks I do have another needle but I'm trying to get as much
use out of this one as possible okay and then further forward than the stitch my second last
stitch that I did and back again so you're basically just doing a regular running stitch
but doubling back in between each forward stitch to ensure that you're getting real like maximum
strength okay and I'm going to continue and do that on both sides and then we will work on the heel
