Using 3D Printers To Build A Car Out Of Carbon Fiber | Part 2 | The Legacy (14)

Tuning Pro
54 followers
#GJWcars #GJWauto #Customizingcar #tuningcar #howto #DIY #CarCustomization #upgradecars #editcar #wrapping #bodybuilding #bodycar
AI Generated·May contain errors
Good promo for this company.
Will is stressed because Tim Dunn activated two Buddhas to be printed.
Double Buddha.
Seems that's how it gets heated.
It's tedious.
It's f***ing lightning.
Dude, you should have seen Tim's the other day.
It was as big as the washer.
I don't know how he was using it.
Very goopy.
Melty, bro.
It's a bit melty.
Will has a system because he definitely ain't sharpening like that.
What's up?
He has some type of system of cutting skills.
Every time I do a cut, I push it in.
Or I try to do the cut fast because it melts less.
And then you push that part in and it will pull it apart, I guess.
I was just having an issue with this one.
Because this one is being completely different radius.
I'll probably end up cutting a bunch of this off.
Or cutting a bunch of this off.
Because the newer end with the little cut technically goes past this, right?
Or do you have to cut the rear end?
I do have to cut the rear end.
Awesome.
We'll see.
Love the little notes.
Epoxy here.
Epoxy edge.
Take a gander, Xander.
Tip mark out.
That was a good one.
Funny big fuzzle.
Oh, yes, sir.
The hole makes me break that straight face.
It's impossible.
Maybe we use one minute to glue two, two, two.
Or run through tips.
Well, I don't have any tips.
So I'll just mix it with a mixing board and spread it.
The globules.
I don't have gloves on.
I was wondering why you didn't have them on.
You're the type of kid that...
Glued my hands.
I ate glue as a child.
Those X-Boys.
Eating glue.
When I was a child, my best friend and I, we would ******* glue our hands together.
She ain't going home, bro.
We're gluing our hands together.
There's definitely carbon in my hand.
Yeah, as soon as I put on my gloves.
And there's a needle.
Feels bad, man.
What is that?
What did you say?
Eating all the Morios.
Killer whale blood.
Is this what goes on the Street Bandito YouTube channel?
Absolutely.
Working?
No.
Weird stuff.
Behind the scenes, that's all.
So behind the scenes is actually the work.
Ooh, you're going fast.
Get gloopy.
Damn, Xander, where'd you find this?
Damn, I thought that was Mueres.
What?
Well, guys, we have ourselves a human plant.
If you need one of these, let us know.
Renting for 20 bucks an hour.
Doing parties.
You just hold stuff.
God, this was clamped so well before we brought fricking epoxy to the equation.
Is that so?
You think that's really what did it?
Them fires are going to be photo.
I'm never going to live that way down.
The full support.
Knees, hips, back, elbow.
I don't know if I can move yet.
Head, shoulders, knees, and toes.
Sure.
Forward like half an inch.
We'll probably have to cut all the way back.
Do we have a spoke we could put on this car?
We should just do this all at once.
We can literally screw this in and not have to hold it like this.
We're just guessing upon not even knowing.
Is that really what your main concern is?
Yeah.
How am I supposed to drive this?
It's right hand drive, right?
I'm not going to fit if we put seats in the car.
You're not going to fit?
No.
Are you sure?
Look how close my head is to the cage already.
You'll just have to wear a helmet.
From the factory, they dropped a nut back here and they just glooped over it.
They're like, who cares?
You better be lucky.
You don't even want to focus.
My other one was literally down to this.
You could have kept it.
Wow, these strut towers look like something.
Hey, now.
Don't worry about it.
Oh, snap.
Does it use the same lugs?
No, these use conical.
Do you have conical lugs?
Sure.
Are we really just putting these on?
I keep forgetting how long this mic is.
It is about to poke me.
Son of a bitch, I know the way.
Oh, hell no.
I thought you could fix it.
I don't know what that gloop was.
So, that's it.
Epoxy it on.
We have quarter.
It is quarter.
Wrap it up.
Next step is going to be doing the other side, making it match exact.
And then we're going to tape and back the back of this so a bunch of foam doesn't pour past there.
And then foam this hole, Johnny.
Or maybe I'll just fill it up with a piece of scrap carbon or a rocker panel.
I thought that was just some board.
Scrap wood?
Yeah.
Disrespectful.
This is our rocker.
I can go over here.
Wherever the back of that is, I can usually see it.
I've beveled the edge.
It's nice.
Well, I guess we'll see you tomorrow.
Yeah.
Alright, so we have our molds all finished.
I've gone ahead and prepped and gel coated the molds.
But we actually have a three-piece mold here where there's a seam along this body line and a seam along this back section, too.
This back section removes that direction.
This top section moves up.
And then this section moves out.
Obviously, with the dimensionality of it, the part would be caught in the mold and never be released, as well as the mold never being released from the plug itself.
So, multi-piece molds are a little more complicated and annoying than regular molds, but not by too much.
You make your part, and then we'll unbolt it to then release it out of the mold.
You can see I just kind of drilled holes and ran bolts and nuts through them.
You can use clay and do little key marks, but I found this method works just fine for me.
If you're doing, like, a really high-production part where you're making a lot of them, it would make more sense to do something keyed where you can, like, throw it together really fast.
But for this, this works great.
And obviously, we only got, you know, a couple weeks before SEMA, so we need quarter panels.
So we're just going to keep going as fast as possible.
You don't see all this green stuff.
I used that fiberglass filler.
If you watched the FE32 episode on mold making, I explained why that's – I kind of randomly came up with this method.
I'm like, it's the same exact hardener as the gel coat, the tooling gel coat, and it also is fiberglass in the filler.
So this helps keep a lot of the really intricate details where, like, laying fiberglass in can be kind of annoying on molds.
So it makes the mold process way faster and keeps it really accurate.
But we have already set in some stabilized carbon fiber.
I keep talking about this stuff, but I don't think you guys understand how great it is.
The downsides to it are it's not very good with complex curves where, like, if it was just a curve in one dimension, that'd be fine.
But this curves this way and this way.
So if I put a piece of stabilized here, it would wrinkle because the whole fact of, like, the back half having, like, a little mesh weave on it,
it stabilizes the fiber so they can't turn and get, you know, start fraying or get, like, un-uniformly, like, set.
So that makes it, you know, not very usable for complex curves like that.
So all the spaces I can use it, for the very first layer, I'm using stabilized just to make sure, like, I have exactly 50 inches from here to back there, or, like, 49.
And carbon comes in, you can buy it in a 60-inch roll, but I usually get it in the 50-inch roll.
But even with a 60, I would not have enough length to go from there and go all the way out here.
So I'm going to hide a seam behind this piece right here.
This also keeps it so the weave is going the correct direction.
And, yeah, getting the weave in the right direction is, like...
The biggest challenge?
Yeah, it's not a challenge.
It's just something, like, an extra step that you really got to remember if you're going for that.
In our first Z, we were not worried about it at all.
We got lucky with some of the pieces.
Some of the pieces, the weaves just go in the opposite direction.
It doesn't really bother me too much, but with this Z, we're putting a nice V seam down the entire thing.
So it would be kind of silly to put a nice seam down the entire thing and then have one of the parts not continue that same directional weave.
So I marked all the stuff on the mold itself.
So this is all underneath the peel plot.
I mean, not the peel plot, the PVA and the wax and stuff.
So you won't see this big R in the part or anything like that.
We're going to do four layers of regular, unstabilized 3K as the final pieces.
I'm going to lay one more piece in here of stabilized because the length of this is too long to be able to put a single piece across there.
So stabilized comes with a little plastic backing that you can peel off.
It's really nice because you can write on it.
And you can see on the backside, it has like a little tiny, fine little lines.
And they're essentially just holding the weave together.
So you can, I've actually experimented.
You can put that side down.
You can't really tell, like even like a piece like that with this side down in the mold versus the regular side without the little weave.
You can't really notice it, honestly, once it gets wet out, which I'll go.
But as a rule of thumb, put the weave side on the back section.
My gel coat is completely cured.
So it's like a little sticky, but not too crazy.
So I should be able to lay this in here without too much trouble.
That goes in.
Yeah, it's similar.
It's almost like prepreg where like, well, maybe even like stickier than prepreg.
But yeah, it goes in without too much issue.
You want to be careful when you're laying up into gel coat.
If you lay it up and then you want to peel it back up, you have to peel it really slowly and delicately.
With stabilized, you can peel it up without it warping and jacking up the look of your weave.
Whereas with like a normal piece of 3K, what we would do to try to mitigate that would be lay epoxy resin in here.
Like the System 2000 resin in here first.
And then lay the, like, so it'll combat some of the stickiness of the gel coat.
And then you can kind of slide the piece of carbon on it without it, you know.
Gives you good slippage.
Yeah, without it sticking in one place.
And you try to pull up the regular non-stabilized carbon and it just is a nightmare.
What about the slip?
It's all about trial and error.
We've done plenty of error.
That's how you learn.
This is just a car for me to put around town.
So we're not too worried about it.
It's not like some crazy show car.
Although we are going to be competing in Battle of the Builders, so come out to SEMA.
I'm sure the people that are, like, building cars for, like, three years and we're here with a car we're building in six months.
Like, all right, here we go.
I actually have one last piece of stabilized carbon that's going to go right in here.
A little sticker.
The tip of that just got me, Odell.
All right, so I'm going to mix System 2000, wet it in here, and then I'm going to need your help, Xavier, to lay this bad boy in here.
So we're going to have to jump to time-lapse.
All right, here we are a day later, and we have both quarter panels.
We'd already previously made this one, which I'm actually going to have to remake.
We had a couple problems with the mold.
I've, like, cracked.
I think I might have put too much pressure, like, vacuum pressure on it, and it, like, pulled in here.
It's kind of deformed this little section right here.
But also, like, the weave mainly I've put in the wrong direction.
This could be probably fixed with a little bit of gel coat and some time.
But I sent a photo to Will, and he's like, yeah, oh, man, that sucks.
The weave's in the wrong direction.
I'm like, what do you mean?
I even marked it.
You can kind of, you can't really tell, but before I fully wash it off, I marked it in the mold correctly.
I even put, like, the little stabilized carbon pieces in the right direction.
So that's correct, and down here's all correct, but this is the wrong direction.
So the rest of the entire car has a really nice V-weave herringbone down the center.
And then this is the opposite direction, so we've got to remake this panel.
But the panel we actually made yesterday came out great.
I washed it off, but I didn't get all the clay.
This is, like, high-temp clay that fiberglass sells.
So you can use it on, like, prepreg molds if you have a small little void,
or if you have multiple pieces of a mold together.
I like to run a little bit in the seam of it so it doesn't, like, pull vacuum through it
and pull all the resin out of the seam or something like that.
Yeah, this one came out great.
It needs a little bit of blocking, kind of like the fenders and stuff like that.
Like, we use gel coat on these panels, so they give us, like, you know, a couple millimeters of room to play with.
I guess with gel coat, you kind of treat it like body filler.
Yeah, it's like a really thin piece of body.
So, like, we could just sand with 320 and clear these, satin clear these parts, and they would look great.
But I can also, like, take 180 and block it and go right into clear from that, too.
And it'll be really straight and, you know, be a little bit nicer than this.
We'll go ahead and do that.
It's easy enough to do.
But, yeah, unfortunately, I got to remake the other side, but whatever.
That's composites.
That's the life you chose.
Yeah.
I did actually pull off the metal door jam piece.
Oh, yeah, like the quarter panel and the jam are two separate pieces.
I have it right over here.
I like the fit in it.
I guess you want to, I guess, bring out some camber or...
Yeah, yeah.
I sucked it in just to get out of the way of the quarter panel so it would clear it.
So this was the jam piece.
You can see, like, somebody had filled with fiberglass filler through.
This is usually, like, a rubber bump stop on 260 and 280s.
And they filled it with this fiberglass filler.
Look at it.
What?
Yeah, dude.
It was sitting on the inside of the rocker.
The rocker comes in this way.
So it was just globbed in there.
Rust repair.
Rust hiding.
Yeah, exactly.
That's what most repairs are for rust.
But we want to keep this, which is, like, the floating adjustable door latch.
So what I'm going to do is hit these spot welds that I marked with the Sharpie.
And then we're going to bond this to the backside of the quarter panel.
And, like, the two holes that these float around are noted in the actual mold of the quarter panel.
So you can find those two holes.
Line them up with the holes here.
Bond it.
Have a nice solid door latch.
Save a couple pounds.
Probably, like, five pounds at least.
Will you still have to put your knee in the door?
On this one, hopefully not.
I would like to, you know, make inside and outside shells of, like, the hood and the trunk and the doors.
But with SEMA being, like, a couple weeks away, we don't have time.
So I am going to use the metal inside shell of the doors.
Which I can always, like, trim off later and swap out with carbon ones.
Because I'm going to be making full carbon doors for 240s and 280s anyways, just, like, OEM doors.
So I would need the inside mold.
This will use the same mold as that.
But, yeah, so for time's sake, we're going to use metal insides of the doors.
Inside of the trunk, I have two separate trunks.
The trunk from this, her car, actually, from Mariah's car.
We're going to use the inside section.
Take the outside skin off.
Bond our carbon skin with our spoiler and everything like that.
Bond it into it.
And then I'm thinking I might do the same thing with the hood.
We're, you know, 80% through.
But, again, we only have a couple weeks for SEMA.
So we got to really keep pushing.
And one big note.
Make sure you stay hydrated.
Yeah, yeah.
Liquid Death, sponsor us.
We haven't contacted you at all.
Liquid Death addict.
I got one a day, all right?
It's my time.
It's my little treat.
Little water.
Look, it's naturally flavored.
And it's only got 20 calories for this entire can.
And it has how many grams of sugar is it?
Whatever it is.
Four grams of sugar.
That's his secret to staying jacked, as people have been saying.
Exactly.
Liquid Death, that's how.
You don't need to go to the gym.
Nothing.
Don't watch your diet.
Just drink Liquid Death.
Terrible advice.
Yeah, yeah, don't do that.
But yeah, so we're going to go knock out some doors and some rocker panels in the next episode.
But until then, we're out.
