MAKE YOUR OWN Race Car Parts | Carbon Fiber DIY KIT

Tuning Pro
54 followers
#GJWcars #GJWauto #Customizingcar #tuningcar #howto #DIY #CarCustomization #upgradecars #editcar #wrapping #bodybuilding #bodycar
AI Generated·May contain errors
Just for you.
Okay, guys, this is gonna be a tutorial on how to make a part from our DIY large carbon fiber
composites kit that you can find on IndustryGarage.com
Okay, so now we're gonna go over everything that comes in the kit. So for the large kit, you'll get five yards of
3k 2x2 twill carbon fiber. This is probably the
most commonly used carbon fiber, one of the best weave patterns of mine.
Most of the 240z is made out of this.
You're gonna get the System 2000 laminating epoxy resin and
thing of the 2060
60 minute epoxy cure. That means it has a 60 minute pot life, which gives you more than actual 60 minutes of working with it, but
that'll give you the most time to mess with this.
Unless you went with something crazy, but it's plenty of time. You're gonna get a roller with a bunch of polyester
rolling sleeves. It's gonna come with a ton of gloves, more than you need, and a ton of brushes, more than you need.
Two different sizes.
One of these rollers to help get air bubbles out. A bunch of squeegees. It's cool having like the different versions of like
ways to apply the resin available to everyone because some people might really like the roller. Some people might just like
brushing on only. I mean, I really like squeegeeing.
But they're good for different times also, but you can kind of get a feel for how you like to apply stuff.
Make sure they do the
crazy glue trick with the brushes. Yes, we'll go over that again in a minute.
But it also comes with their gallon mixing kit, which is everything here. All these cups, these mixing sticks,
different measuring things,
and then everything you need to
release your mold,
aka your hood, whatever part you use. So we're looking at PVA release film and
the part all paste.
Okay, so what are we making today? We're gonna remake Xavier's S2000 hood.
It's a fairly easy part. It's pretty flat.
So what I've done so far is just sanded the whole top with 1000 grit. You can see there were some like little like
dirt nubs in the paint and other small stuff.
It's not super necessary, but I figured I'd get them down. It takes two seconds to
sand this thing with 1000. It's a flat hood, and we're just gonna make the outside shell of it.
So we're gonna do four layers of carbon fiber,
3k,
2x2 twill, and that should be plenty. And then we're gonna cut the skin off and
use the bottom section of the actual aluminum hood, because this is aluminum, and
bond that to the carbon fiber outer skin. What we're gonna start with though is
part all paste. So you'll have this exact same size container, and you want to just
apply the wax and
buff it pretty much right off.
I'm doing a part this big. You want to wait at least 30 seconds, so by the time you get to the other side
it's been at least 30 seconds.
Set a layer of wax on, then buff it off. You want to continue that four times.
So you have four layers of wax built on, and then the final one you make sure you buff it off pretty well.
You can go a little liberal at first with the wax and then
kind of
stop doing as much later.
All right, we're buffing off our last layer of wax.
You'll still see a slight residue on it, but it's fine.
We're gonna spray the PVA release film next, and that will even everything out.
Make sure you use a new towel each time, each
layer.
I'm going to be spraying my PVA out of a
automotive paint gun, but you can brush it on.
You can use a roller to roll it on. There's a bunch of different ways you can do this, but I really enjoy
spraying it on. That's what I'm gonna do.
Okay, with the PVA you're gonna hit it with two medium wet coats, and then let it dry for about 20 to 30 minutes.
It's supposed to be behind the scenes.
I really feel like Speed Racer with these white gloves.
All right, so it's been about 30 minutes.
Our PVA is completely dry, and now we're gonna move on to the carbon.
There are multiple ways to lay down your first layer of carbon.
You can lay down a layer of epoxy first and lay the carbon on top of that.
You can lay down the carbon first, put the epoxy on top of that.
Whatever way you want to go. It's a little easier to make your weave perfect.
If you're gonna make the inside of this part, it's gonna be seen.
So that's gonna be the part that's sitting against the outside of the current hood.
So what we're gonna do is we're gonna make sure the first layer is perfect.
We want the weave to be straight, not any wobbly weirdness.
We're gonna go ahead and measure out our carbon first, lay it down, and we're gonna start mixing some System 2000 and
2060 Hardener.
You definitely want some good
carbon fiber shears.
We have these available on IndustryGarage.com, but they're also available through Fiberglass.com as well.
We do our same trick of
pulling out a single carbon fiber strand or maybe three. That gives you a straight line.
Well, it doesn't look straight for us, but it's straight for the actual weave of the carbon.
Nice audio. Let me get closer.
Got our carbon cut. We're gonna go ahead and lay this on there dry.
Nice thing about it dries because you don't have to worry about this. If it was wet, if you
lay your carbon down, you don't get it
like perfectly set on the first
layup, then you can run into problems where you have to pull it back up and you can pull off your PLPly.
I mean, sorry, your PVA
And that's no good. Actually, I'm gonna wet it out first, then I'm gonna trim
the edge. You don't want to let the edge of the carbon sit too far over
your part because it'll droop over like this. When it droops over, it actually raises up
at the edge. So you get a big air pocket right on the edge of your part.
So you want to cut as close to it as you can.
But I want to make sure I don't cut this dry and it's all shifting back and forth, then I cut it too small.
Because we're right here on the edge.
So it's just wide enough in the back of the S2000 hood, but the front we got
10 extra inches probably total. So we're gonna go ahead and mix some
System 2000 resin and
2060 hardener and start laying it up. Okay, a little tip for these brushes.
You want to do is take some super glue. A subscriber actually told me about this.
And run it across the base of this. It'll hold all the little fibers in.
Last thing you want to do is have a fiber...
Let me see if it's soaked in. Yeah, last thing you want to do is have a fiber get loose in your part.
We don't like it. No hairs. I'd like to dedicate this segment to Deathstroke.
Your hashtag will be used greatly.
Okay, so we're gonna be mixing our
2000 resin with our 2060 hardener.
And it's a
three to one ratio. So three parts epoxy to one part hardener.
And in their gallon mixing kit, they give you a bunch of different cups. You take the largest cup to mix in
and you fill the second largest cup with epoxy.
Fill the largest cup with epoxy and fill the cup that has the green lid
with the hardener. It actually ends up being a perfect three-to-one ratio.
Just take both of these guys.
That's the definition of idiot-proof. I love when things are idiot-proof.
Because I'll be having some real idiot moments.
Everybody does.
Cool. And you can reuse those again. So if you need to mix another one, you can just boop boop.
Makes it a lot easier. You don't have to like go weigh in and stuff.
So...
And there's also a bunch of different sized cups with like actual
measurements. Like this actually has measurements on it. So if you're mixing a smaller amount,
you can always do what it says.
Three to one. It's always the same ratio.
Cool. I'm gonna take my
blue squeegee and my brush and
start applying it.
I'm gonna tack down a spot by putting some resin on it to keep it still.
And since we're putting the
carbon onto the part dry, we want to make sure that we really squeeze it all through.
So I'm gonna definitely hit everything with the squeegee. Get all the air bubbles out in the back.
So I'll start with that much.
And squeegee it in.
And then once we get to the end and we get it all covered,
then we will
trim the outside of the carbon so it all matches.
Work your way from the center
out.
Definitely helps. If you go from the outside in, you can get some air bubbles trapped inside.
Squeegees are pretty easy to press out, but it's always easier.
So you don't press the air bubble out to the edge. If it's fully wetted out,
then it won't come through the fabric very easily.
So you might as well push it all the way to the edge and you can push out the edge of it.
You can already see when I go over this
this edge right here.
Right here.
It'll stay down when I actually tap it down, but you can see it starts to raise up. That's because this is hanging over.
So a little extra
resin and then a good trim nice and close. We'll take all that out of there.
It's almost like he's just a
professional, professional,
super sophisticated, licensed, certified
composites man now.
Yes. After building one whole vehicle, a bunch of extra parts,
we shall call him resin man.
All right, so I'm gonna cut pretty close to the edge.
It's not a great idea to cut wet fabric with your nice carbon fiber scissors, but if you
wipe them down with like some lacquer thinner, mineral spirits, or paint thinner or whatever, after you're done,
just make sure you don't forget.
You can see here on the edge, the carbon is running flat and then right when it gets to the edge, it's bumping up.
That's from this dangling carbon.
If you cut it and then smooth it back down again, and it doesn't have any resin, I mean any carbon excess weighing it down,
it'll actually lay flat. It's kind of odd that it
bunches up like that, but
cut it off, you're good.
And on this
this second layer, the
weave is going
90 degrees different than the last one. The last one was going this direction. That'll help for any warping of the
of like the hood after it's made.
You usually want to
crisscross your weave. It makes the part a little stronger.
I'm not as worried about getting the
weave exactly perfect on this one because this is gonna be a middle layer, so it'll never be seen as long as it's
not bunched up or doing anything crazy. As long as it's laying flat, we're okay.
Getting rippy.
Evenly disperse this extra resin I got
with the roller. It's very satisfying.
If your resin is even between your layers of carbon, then it should lay flat.
You don't really want some of your part to be more resin rich than others either, so.
So now all of that wavy resin is now dispersed evenly.
And we can roll on to our
final layer of carbon.
Yeah, yeah, because now we're 90 degrees different.
Come to me more. Yeah, just keep your end up and I'll
let a little bit of slack. A little more. Thank you, sir.
Yep. Thank you, sir.
All right, so we have the
final layer of carbon on.
I'm going to squeegee this one and
and then go back with just the brush and
make sure it's got a lot of resin. It's a little resin rich on the top layer.
This is Xavier's hood for his car that we're repainting right now, and we're actually gonna end up painting this, but
for this project, we're gonna make it look as good as possible. We're gonna leave some accents though.
I don't know how, but. We're gonna leave some carbon. And the inside will be all carbon, too.
So when you open the hood, you see that. It'll be humble baller status.
Humble baller. I think the most exciting part from this for me is
not getting any more dents. So as I'm squeegeeing this, more tips.
The roller is very nice to use in the middle layers. I wouldn't use it on the first or final layer.
Just because it it gives off a little bit of fuzz from the roller. Not much,
but like you probably wouldn't even see it in the part.
But just in case, I would only use it on the middle layers of your layout.
I mean you can,
Xavier and I were talking, like if you're trying to get lint off of a roller when you're painting, you can always roll it on
some duct tape or something like that. Try to get some little lint babies off.
They all have their their pluses, like the
squeegee will get all of the air out, make sure it's really really tight, but
it doesn't leave a lot of resin on. And the brush
leaves a lot of resin on, but it doesn't get it very tight.
And the squeegee is like right in the middle, but the squeegee also is the best for getting it really even.
You can get it even with a
squeegee. The roller is the best for getting it even.
Luckily the kit gives you all of the tools you need. Just make sure you use them the right application, you'll be good to go.
Also as you're laying it up, you might have noticed we laid up
with two layers that where the weave is going this direction, and two layers where the weave is going this direction.
You can see the weave is like the carbon
darker line, kind of
follows that pattern.
It'll be a 45, and you can even do a zero degree where you cut the part to the side,
but this part's too long. We'd have to have an intersection of like two different
layers of carbon, which could create a problem.
For this,
just intersecting them is more than enough.
Keeps the part real stiff.
Otherwise if they're all going the same direction, it'll want to bend in one direction more than the other.
It'll be stiff this way and bend that way. So you're slowly applying this layer so you have like a better
resin ratio, I guess.
So I'm adding this last layer in here, well this extra layer of resin on top.
Now that I've squeegeed everything out and made it all flat to
give a good boundary between the weave and the top of the part. Because if I left it like this, the weave is textured.
So if we like prime this, you'd see the weave in it.
Some people will use like a gel coat
to add on the last layer and then sand that thing smooth, but I like using the resin. Speed Racer, watch the Speed Racer again,
it's just so funny.
He was making fun of it at first, but now he's like...
It's entertaining.
The show would not...
Speed Racer would get canceled real fast.
Like talking to his like girlfriend, he's like,
Trixie, she's just like, oh, it's so nice out. So beautiful out here. He's like, Trixie, stop talking. I'm trying to think.
The thing you can try is running a torch over it. If you have a lot of air bubbles. Let's try the torch real quick.
Just for fun.
So in our final thick layer of resin, we have a little bit of air bubbles, which aren't the end of the world.
You can always just sand them off later.
Do it again. Or, if you want, you can try hitting it with a little bit of heat.
It'll bring them all up to the surface, hopefully pop them.
The master of perfection.
It's better. You can still see a lot of the actual texture from the carbon weave.
Whatever I don't want, that cutting process is what really gives you that...
The polishing.
All right, so we have four layers down here, all of our resin set.
We just need to let this all dry and come back and hit it tomorrow.
Today's the big day.
Tim is finally clearing all the parts. Get to see how the final product will look.
I'm down bad right now. Ate two jalapenos.
And my stomach's on fire.
Trying to struggle to make it through this long day.
Ryan, beside us, has been here since 6 a.m.
Working hard.
Working hard or hardly working? Working hard.
My grandfather used to say that all the time.
Just for you.
We're serious here.
Don't give me no wet socks now.
Dude, those socks...
Your get-up in general as a shopper just doesn't make any sense.
I get up and I go.
I don't even look down. I just jump out of bed and I start my day.
Our hood is looking perfect, but how did we get here from where we were?
So we let it sit overnight and dry completely.
Sanded it with 80 grit and we hit it with another layer of resin.
Let that dry overnight.
And then we sanded that with 80 grit again
and then stepped it up from 80 to 120 grit to 180 grit to 320.
And then prepped it for paint.
Clear-coated it three times and this is the finished product.
A gloss for you guys.
Even though we like satin clear.
Like I said, we're the matte boys.
We're matte, yeah.
I mean, it does look cool having a gloss.
We did a pretty good job of laying our weave straight.
So now we have an outside shell of carbon fiber.
So where do we go from here?
The inside is...
We taped it down so it wouldn't fall away.
It's fairly easy to release.
So the inside looks good.
We're probably going to matte clear the inside of this
because we like matte.
In the next video on this hood,
we're going to grind around the outside
and actually bond this to the old shell.
And we have another thing.
We started messing with the CNC machine
and we cut out a prototype
of some kind of universal hood vents.
These are slightly larger than
the average size you see now.
So we're thinking it's going to fit perfectly.
Once it's made in prepreg,
it's going to be really thin and malleable
so it'll contour to the hood perfectly.
So I think these on the sides
will give him a lot of ventilation.
We're trying to get a lot of the temps
out of your engine bay, right?
Is that the main point of doing most of this?
A little weight savings and have a carbon fiber hood.
So we'll go through all of the
final steps of how to bond a skin
to the inside of your hood in another video.
But for now, that's it.
If you want one of these DIY kits,
we sell them in a large kit
that's big enough to do a roof
or a small kit that's good for
a 2 foot by 2 foot part.
This hood's pretty long
but we still had 10 extra feet.
So even with the large kit,
you can make another part if you really wanted to.
There's a lot of resin and extra stuff.
You're set up to make more parts
but it's at least enough to cover a good bit.
If you want yours, you can go to
www.industrygarage.com
We have them all listed under IG parts.
Until next time.
