KelTec Sub 2000 CQB Integrally Suppressed Carbine: It's Dangerous 👀

Uniform & Arms
3 followers
1 Video View·Jun 17, 2026
We take the KelTec Sub 2000 CQB Integrally suppressed folding 9mm to the range, go over its features, and discuss the issues we had with it so far 🤙🏽
AI Generated·May contain errors
Welcome back everyone. As you probably guessed from the title, the thumbnail, and the intro,
this is the rifle that we are going over today. This is the Kel-Tec Sub 2000 CQB. So,
why is it called the CQB? Well, it is intricately suppressed, meaning that it is a one-stamp gun,
meaning you only need to get one NFA stamp in order to own this. Now, that's good because you
don't have to get two, i.e. it's not a short barrel rifle. So, basically, we have four inches
of barrel, four and a quarter, and then after that it's pinned the outer sleeve here. So,
that way it makes the barrel legally 16 inches long, chambered in 9mm. It is essentially an
intricately suppressed Gen 2 Kel-Tec Sub 2000. And I suppose before we get too deep into what
that actually means and the features and stuff like that that it comes with, we need to thank
the sponsor of today's video because I did buy this gun and definitely was not sent out to me
from Kel-Tec, so we've got to cover the bill. So, we want to thank these folks right here at
Battle Cat Company. They manufacture apparel and just soft goods, patches, stickers, things like
that for Pro 2A folks. They are unapologetically Pro 2A, so we definitely appreciate that. And
obviously, they make some cool stuff with cool designs that folks want to wear. There will be
a link down below if you guys are looking to pick them up. So, definitely recommend heading over
there and checking them out. Now, getting back into what this actually is. Being a Sub 2000, one of
the biggest features of it that people like is the fact that it is folding. So, basically we are going
to drop our magazine here. I prefer to put the bolt back to the rear. I know some folks in the Kel-Tec
world will argue about that, but that's all right. And then we're going to push the barrel forward
there. At this point, it cams up and folds. Now, on this Picker-01, what I do recommend is moving
this piece down, so that way we can actually turn our optic away for storage. So, you can turn either
way, but turn just like that. Now, at this point, you can continue folding it, and there you go.
The handguard here has a piece that latches into the piece on the top of this buttstock, and you
can fold something with optics. So, that is kind of a new thing for the folks at Kel-Tec. This gun
hasn't been around that long. It's only been around, I think, it was introduced at SHOT Show 2020, and
they were only made in limited numbers. So, I suppose, additionally, before getting into all those
details, I do want to mention that today's video is going to be a Mug Club episode, where we're
going to do a free portion here on YouTube and Rumble. Then, we're going to go over to Mug Club
with some exclusive content. We might take this thing apart. I think folks would probably want to
see that, just because of the integral suppressor nature, and you obviously can't do it on YouTube
rules and whatnot. But, take this thing apart, and then, of course, answer your chats as well,
which I know a lot of you guys like. We've been discussing life topics lately over there,
not gun-related stuff, and people have really liked it. So, if you guys are interested in that,
or just any of the other Mug Club folks who are creating exclusive content over there, like Stephen
Crowder, Brian Callen, Nick DiPaolo, they're all really funny. I am not. And new folks are coming
on board. I think that announcement is next week, so stay tuned for that. But anyway, if you want to
head over there, code MRGUNSGEAR, we'll get you guys a free month over there, and you can head
over at the link in your screen. Now, moving back into being what this is. So, obviously, a lot of
folks like this as a backpack gun. At this point, basically, you can unfold it, put your bag in,
run your bolt, and you are ready to go. And I'm not flagging myself like this. There's an open
chamber right there, people. Don't freak out. I can already hear you in the comment section. But,
this gun has a lot of cool things to it that I really do like. So, you can pull back on this tab
here, and that will release it from the handguard. You can see the handguard has that locking piece
on both sides. And basically, we're just going to rotate our barrel, or excuse me, our overall
forward piece down. And then you lock this piece back in, like so. And then you lock your little
trigger guard back in, and the gun is ready to go. So, getting into the details, I suppose,
from the butt to the end of the barrel. Stock here is the Gen 2 Kel-Tec stock. It has some
interesting features on there. I know there are aftermarket stocks available, if you guys want
to go with that. It is not an adjustable stock, though. It is a fixed position stock. But it is
definitely an upgrade over the earlier Kel-Tec Sub 2000 stocks, in my opinion. It's just more
durable. And obviously, we have our sling swivel loop there. And it's relatively comfortable for
a hard plastic stock. This gun is a blowback operated design, and it has a relatively large
bolt. So, it definitely has some recoil to it. It's not horrible or anything like that, but you
are going to feel it. That is for sure. As you can probably already guess, this is our bolt release
here. And obviously, this is in the locked back position. And to send it home, you just pull down,
and it goes home with authority, which I do like that. It does feel good. One thing on this I
mentioned, being a Kel-Tec, a lot of people associate that with being a lightweight polymer
type of gun. There's not a lot of polymer on this gun at all. Basically, we just have the receiver
here, our stock, and that's it. Everything else is either aluminum or steel. So, it feels like
a well-made gun. But continuing on up here to our grip assembly, this one right now has their
multi-mag system. Originally, when they mentioned or debuted this gun, they said it was only going
be available for Glock pattern mags. And now, they just have two different patterns of grips
here. So, they have the multi-mag that takes pretty much all the common mags. So, M&Ps, Berettas,
SIGs, whatever the case may be. Those geese are going nuts. They must know about the accuracy.
We're about to show you in a little bit. But anyway. So, this has the multi-mag system,
which I actually think is really good. It's a good design. And basically, you just change a
plate out here on your receiver, and it works with the different catches that are on magazines. I
think it's very smart. Honestly, I think other companies should, you know, look into using it,
because it's smart. So, basically, if you have a few different popular defensive guns, one of them
will work in here. So, that certainly is nice. Safety here is a cross-bolt design. If you see
out here on the red, red is dead. That is, you know, the traditional indicator, if you will.
And then, our bolt is there. Now, on this particular gun, on the CQB variant, they've
taken out the rear sight here and replaced it with that clocking piece there. I think a lot of
folks with Kel-Tecs, not a big fan of their sights. I'm not. Particularly their Gen 1 sights.
The Gen 1 sight was really bad, in my opinion. The Gen 2 is okay. It's usable. But this system here,
for the optic anyway, is much better. Continuing on out, this is all aluminum. They do etch it there
and say, caution, surface is hot. But honestly, it doesn't get that hot. Like, we were firing
a ton of 9mm, most of it supersonic, through this during the two, three testing days that we put
through it. And really, it doesn't get all that hot. I should mention the grip up here is polymer
as well. So, it's a little bit more polymer. But it's a polymer, like, overmold. And honestly,
heat's not that big of an issue, despite the fact that it's basically etched on there 15 times.
But it doesn't feel super front heavy like you might think it would. It's fairly balanced. And
I think a lot of that has to do with the bolt weight back here in the rear. But I know what
you guys want to see. You guys want to see why I titled the video the way I did. So, with that,
let's head out to the range and see what kind of groups we can get out of this gun. We've got the
target downrange at 25 yards. Normally, I would do this at 50 yards. But zeroing, we didn't have
the best luck with it. So, moved it in a little bit closer to kind of see what kind of groups we
could get with it. And we'll see. Up first, this is 115 grain Minuteman Munitions Total Metal
Jacket. And we're using a CTK Precision Rest and a Northak Red Dot on there. We'll see. That last
one, you guys probably didn't see it. That one hit the dirt before the target. Let me check here
through the binos real quick what kind of results we got outside of that. So, unfortunately, that's
very similar to what I've seen beforehand. I'm going to go down there. I'm going to mark those
real quick. And I'm going to come back and we're going to try some Norma and see if that tightens
it up. I'm also going to bump it to the right a little bit because that does look like it was
off to the left. That said, I'm honestly not sure it's going to help. But we will do just that.
This is the ammo I tried to zero it with. So, you guys see why, again, normally we
test accuracy of PCCs at 50 yards here. This is why we moved it into 25.
Who knows though? It might be ammo. It might just be that load it doesn't like. But that load shoots
great in some other guns. So, let me go down there and mark them. Come right back. Target has been
marked. Now we are going to load up five rounds here of this Norma. This is 108 grain, but it's
a total copper jacket. So, total copper bullet, if you will. So, it's going to behave like a heavier
grain projectile. Has to do with the length for the new folks. So, we will see how it likes it.
Hopefully it tightens up. All right, let's pick them up. As always with the accuracy results,
you guys have a better idea than I do before walking down. At 25, I could basically see them
though. So, again, with the first group up, which was Minuteman, that's kind of the one that I've
lined through here. So, this one, this one, down here, and then here. We also had one that hit low
in the dirt before the target. So, it was quite a bit off on that one. So, with that group there,
it's about 10 inches at 25 yards. So, would that be a 40 MOA group? Not good. So,
then we switched over to the Norma. See if there was a difference there. You guys have watched
the footage of it. I think that was one of them right there. That's why I put the question mark,
but the other ones are circled. And it's 10 and a half, 10 and a half inches with the Norma.
So, again, that's over 40 MOA group. For those who don't know, this is not, if you're new here,
this is the first video you're watching here on the channel. I have lots of PCC videos on the
channel you guys can watch. I can pretty much always keep them definitely 10 MOA or lower
for sure. And also, normally 4 MOA are tighter with a 9 millimeter carbine or even a 45 for that
matter. So, something's up with this gun for sure. So, the groups that you guys just saw
fired were fired months ago. And actually after that, I didn't really know what to do with this
video, how I wanted to do it. I went back out and actually tried it again with two different loads,
Federal HST 124 grain plus P, and then also with some 147 grain Spear Gold dots. And it actually
got worse. Those two are 12 and 13 inches in terms of MOA, like at 25 yards. So, it actually
got worse with those two rounds, but I wanted to give it another shot and make sure it just wasn't
two loads and it wasn't. And I just kind of want to give context to why I say this gun in its
current configuration with the accuracy that you guys just saw is dangerous. So, there was recently
a 45 caliber gun that was all around the internet probably last year, I guess. And it would shoot
flyers. It would shoot one, it's about similar accuracy to this, but it would shoot like four
good ones and then one flyer, four good ones, one flyer, five good ones, one flyer.
And a lot of people out there were saying, you know, it was okay. And for a pistol caliber carbine,
it's okay because generally speaking, you're going to want to shoot at, you know, home defense type
instances for this type of gun. But just an example that I thought of off the top of my head.
So, one of my family members that lives in an area, it's pretty remote, not like super remote,
but it's a rural area. There's farms and things like that, but there are houses as well. So,
one of their neighbors has a range, like a homemade range with like a five foot berm.
And basically, they just put their targets at the base of the berm and shoot at them from like 300
yards in it. And so, it's a perfectly safe setup provided, you know, the person operating the gun
is doing everything correctly. But if you think about that, if somebody were to take a shot at
200 yards, let's say with a nine millimeter, even at 100 yards, let's just say, right, that's
what the groups were talking about. That's anywhere from 40 to 50 inches of dispersion that you could
get, right? So, if you have a five foot berm, you think you're doing everything right, and you have
your target up two inches, two feet, excuse me, off the ground, you could send one mechanically
over the berm without even knowing it easily at those distances with the accuracy that we have
from this gun. So, in that situation, I know there's a lot of them out there like it,
absolutely, it could be dangerous. Additionally, you know, if you think you have to take any type
of precision shot at 25 yards, like a headshot at 25 yards with this type of gun should be super
easy. This is one of the reasons people go with pistol caliber carbines is to be able to shoot
more precisely and quicker than you would with just a regular handgun. And honestly, this doesn't
qualify for that with the accuracy that we saw out of it. So, it just has issues. Now, this gun will
be going back to Coltech after this video. I did some research online and it found out I wasn't the
only one that had these issues. Obviously, like I said, these guns aren't super popular.
They're just not just because the NFA item, National Firearms Act item, being suppressed
like it is. But I wasn't the only person that had these accuracy issues. Other people didn't,
but other people did. So, in my opinion, it's simply, it's unacceptable. I really like the
design of the gun. I think it is a cool gun. If this gun was accurate, I would love it so far.
Because so far, it's been 100% reliable, too. I should point that out. It has not had any
malfunctions at all and it's pleasurable to shoot for a blowback gun. And it sounds pretty quiet.
I haven't metered it yet. Hopefully, this is just going to be part one, though, of this video series.
Because like I said, it's going back to Coltech and it just needs to be fixed. It's not okay the
way it is. Now, from everything I've heard, Coltech service, apparently, is customer service is very
good. I've never used it, but I hear good things. So, hopefully, part two, this gun comes back and is
shooting at 25 yards, two to four inch groups and is perfectly acceptable and we all love it. Now,
one reason I thought that it might be having these issues is, obviously, if we take it apart
and kind of swivel it, it's this swiveling. So, sorry about the construction noise in the
background. If the mic's picking that up, they're building a dock out there. So, this is the way,
typically, you would store it, right? And then you'd want to twist it down until it's back where
it should be, but it actually has the ability to twist past where it could be. And I wonder if
there's some sort of chamber issue that's going on with that. I don't know that for sure. I'm just,
you know, spitballing here because I've shot lots of sub-2000s and all of them shoot perfectly
acceptable accuracy, in my experience. I don't know if it has to do with that rotation and how the
chamber is. I don't think it's actually moving anything that I can see, but maybe it is and I
just can't see it. I don't know. So, if you guys have any ideas of what you might think it is,
let me know down below. I pulled the baffles. They are completely fine. There's no baffle
strikes happening at all. Like I said, it's completely user serviceable. So, I think it's a
very cool design that has a ton of potential. Unfortunately, I think it is dangerous in the
way it is right now to anybody using it. You know, obviously, as the person pulling the trigger,
you're responsible for every round you shoot downrange. And if you're shooting at any amount
of distance, you know, past 10 yards, if you're talking about even a self-defense situation,
you could do everything right and things could go wrong. So, that's definitely not something I like
in terms of what we saw out of this particular firearm. Yes, the optics mounted correctly.
When I shot that video, I think actually that same day, I shot my Smith & Wesson
FPC video, which is another folding 9mm gun. I think we got one and a half inch groups at the
distance. So, it's not that I can't shoot. I know people are going to say that. It's that this gun
doesn't shoot well. And like I said, the groups you guys actually saw were the best groups that
we got with it, which were still bad. And one of those hit the ground and skipped into the target,
but we still counted it because who knows where it would have been if we counted the one on the
ground. So, yeah, that's where we're at. It's unfortunate. I think this gun has a ton of upside
and potential, but right now, it's simply not ready for any serious use at all. And honestly,
it's not ready for plinking, in my opinion, unless you have the appropriate area to do so,
which I do, but I know a lot of folks don't. So, if you don't, I wouldn't risk it. That's
my take on it anyway. Now, let's get into price. I did obviously change location. I think the
construction noise was getting a little bit too loud, but price is one of the very good things
about this gun. So, the MSRP on it is $995. Retail on this one, you're going to see around $800. And
if you consider just the cost of getting a 9mm suppressor, to get all of that, suppressor and
gun, for $800 straight price, I think is a good value. Again, I am hoping this is a one-off or
a two-off because, again, we've seen other examples of this reported on the internet, and I hope
Kel-Tec gets it in, fixes it, sends it back out, and it is awesome. But we will see. For now,
we're going to have to leave it there. And if you guys have any questions, anything like that,
any ideas as to what it might be that's causing these issues, I would definitely like to know.
Again, the baffles look good. The lockup is fine from what I can see. I don't know if it's the
rotation or not. I don't know. We'll see what they say. But if you're new here and you like this type
of video, hit the subscribe button. If you've done that and you've hit the notification bell as well,
and you're not seeing two to four videos a week here on the channel, make sure you sign up for
at the website here on your screen. I recommend a non-Gmail account. It goes out once a month,
and it has all the videos since the previous month's email went out. So that way, there's
no big tech giant censoring your eyes from my content. Additionally, if there are daily deals,
deals on the optics, guns that work, ammo, things like that, it goes out my daily deals email. It
goes out every day, as the name indicates, and it has eight of the best deals that we find on
the internet. If it's in that email, it's the best price. The item is the best price on the
internet. It saves you guys some time. It saves you some money because I've already done the
price comparisons for you, and that's all I got for you. Piss off, YouTube.
