This Danish teak veneered cabinet was literally pulled out of a dumpster—covered in mold, beat-up veneer, missing hardware, and odd repairs. A lot of people say these aren’t worth saving, but I wanted to prove otherwise.
In this video, I take you through my favourite mid-century restoration process for teak veneer: cleaning off decades of grime, sanding delicate veneer, repairing damaged teak edge banding, and even fabricating new plastic sliding door guides by hand (no 3D printer here!). I finish everything off with a rich Odie’s oil treatment that brings out that signature warm teak glow.
If you’re into budget-friendly furniture flips, MCM furniture rehab, or want to learn how to fix those common drawer and door issues on Danish-style cabinets, this one’s for you.
Initially, I was not going to make a video for this piece because I thought that's, you know,
pretty typical. How exciting could it be? But I did a poll on my community page. You guys voted
and said you wanted to see it. So here it is. There are some issues with it, of course. This
is a pretty standard Danish teak veneered cabinet. We've got mold here and a lot of finish issues,
as well as some other repairs that need to be made. Now, part of the reason I did decide to
do this, aside from the vote, was because these pop up all the time on Facebook Marketplace. And
in situations like this, you can usually pick them up for a pretty good price. There are always
people that swear these are junk and not worth the time and effort to put into them. But they
do sell for a pretty good price if they're in good shape at the end of your refinishing. And
teak just has that amazing warm mid-century glow that a lot of people like. So I am going to do
what I can for this piece. It's not going to be perfect in the end. I have to accept that.
But I don't think this piece is ready for the trash just yet. So I'm going to get to work.
First, I'm going to put some gloves on. Stay tuned. My name is Angie and I refinish furniture.
Sometimes I paint and sometimes I don't. But I always do what I can to save old pieces from
the trash. Welcome to my workroom. OK, so for those who aren't familiar with these pieces,
we've got solid teak handles and a little bit of solid trim on the front. But other than that,
this piece is pretty much constructed with pressed wood and fiberboard covered in actual
teak veneer. I noticed a little bit of an issue with this bottom drawer.
It didn't want to slide in smoothly. It kept wanting to catch on this lip here,
which is actually the plastic track for the door that slides back and forth. So we'll deal
with that after. Obviously, we've got a mold and mildew issue. And I want to talk about the
coloration here a little bit. So you can see it's two very different colors. There is finish on this
part, but this is where the cabinet top sat and it never saw the light of day. So it didn't get
a chance to darken with the UV exposure like the rest of it. And you can see here where things sat
for clearly years. Another problem I ran into was with the door guides. So this little plastic
piece, there should be six of them and I've got one. So I'm going to have to figure something
out for that if I want to continue to use these doors, which you can see are in pretty rough shape.
This larger of the three doors fits on this cabinet. You can kind of see where this damage
is on both the drawers and the door. And then the two smaller sliding doors go on the top part.
Now these drawers look like they're solid wood. They are not. This is fiberboard covered in some
nice veneer. And the two sides of the drawer on the back are actually wrapped in kind of a plastic.
And then this front panel here is pressed wood with veneer on either side. Like I said, we've
got a solid wood handle. I'm just going to pop these off. So these drawers are actually already
numbered on the back. And I realized that the drawers weren't in the right order. So once this
drawer is in the right slot, everything slides perfectly. That actually happens a lot with
furniture. I'll see ads for pieces for sale that say things like drawers a bit sticky or not quite
working. Sometimes, actually oftentimes, the drawers are just not in the right spots.
There was no maker's mark on this, so I don't know the exact manufacturer, but I do know that it was
There's also evidence here of a previous repair. And it doesn't look the greatest, but it is a
pretty solid section, so I won't have to redo that. It is pretty typical for these to not be
refinished on the inside. That's just how the manufacturers did it. But I prefer to finish the
insides, so I will be. Now this piece would have had adjustable shelves initially. The only shelves
left remaining with the piece are fixed shelves. I cannot move them without taking the entire thing
apart. But there are holes if someone ever wanted to add extra shelving. For me, this piece is not
valuable enough to justify that effort and cost. So I'm just going to be leaving the shelves as is
and hope people have a lot of large items they want to store. I'm going to start by giving this
a really good cleaning. And although I don't show it on camera, once everything is clean,
I did apply a mold spray, which is going to help kill any active spores. These plastic tracks for
the doors tend to get really gummed up over time, so I like to give them a really good cleaning.
And if I do manage to get these doors fixed, hopefully that will help everything slide nice
and easy. And you can see here just how filthy this piece is. So fun fact, this piece was actually
in a dumpster at one point. I used to have another contact with a junking company, not the guy I
normally deal with now, but this is a while back. And she actually pulled this out of a dumpster,
hoping someone could save it, and it's been in storage ever since. So this is truly the last
shot for this piece. So all of the solid teak handles are in really good shape, but there were
no repairs to make on these. They just needed to have all of the decades of caked on hand oils and
dirt cleaned off. I just used a nylon bristle brush to clean. And then I got to cleaning the doors.
Now the inside, which is what I'm doing here, are usually not finished. Again, this is something I
am going to be finishing. I just like to have both sides finished. But clearly the majority of the
scrubbing here is on the outside. You can see even though this is cleaned up, there's still a bit of
finish damage here. Now this does not have much of a finish on it at all. I could try to strip it,
but honestly not much is going to come off. You can see here the pressed wood core. This is very
typical of Danish teak cabinets like this, and a lot of people don't realize that. I see all the time
on Facebook Marketplace these pieces listed as solid teak just because there's wood grain, and
they are clearly not. But these are still really popular with mid-century lovers.
You can see there's a bit of a chipped corner there. We're going to talk about that in a few
minutes. I'm sanding this with a 180 grit, which is a really fine grit. Normally this would be
your later stages of sanding, but on veneer this thin and a finish this thin, it is usually what I
prefer to do to clean these up. I'm just making sure that these bolts are tight.
I'm going to be using Odie's Super Duper Everlasting Oil on this, just a tung oil-based
finish. I love this on teak specifically. It has a nice soft feel to it and a beautiful
low luster without that sort of plastic-looking coating that lacquer tends to have.
This corner that I'm putting some wood filler on here is actually the bottom of the top section.
It's flipped upside down right now, and I'm just going to try to even this up. There was also a
piece of the solid teak edge banding that needed to be re-glued and clamped, and then just a few
little chips here and there. If you end up working on a piece like this and it's the first time you've
ever done it, and maybe you're not so good with a power sander yet, you can do this by hand.
But honestly, if you start with a fairly high grit and really watch it around the edges,
you should be okay. These pieces are actually fairly good to practice on, these sort of generic
no-name ones. Some of the more expensive ones are ones that you'll find actual maker's marks on.
Maybe save those ones until you get a bit more practice. I did use a piece of sandpaper folded
in half to get right up against these plastic edges. I didn't want to put the sander up against
that and risk tearing them because it's not wood underneath. I did the same thing with the sliding
doors, just very carefully sanding the finish off. I did 180 and then I finished up with a 220,
and actually I used 220 after the 180 on the entire piece. Now I didn't really have to do
the inside, I just wanted to clean it up and have it all look uniform with the new finish on it.
This shelf specifically had to be done, but the rest of it I just chose to do, and I even sanded
the back panel. Now you can see some pretty significant damage to the edge banding here on
this right side. I'm not sure exactly what happened there, it got dinged pretty good, but I'm actually
gonna cut that section out to repair it in a little bit. So here is that chunk that I took
out of the edge banding. Now in retrospect, if I'd had a piece of teak long enough, it probably would
have been easier to just replace the entire edge banding, but I always see these pieces as great
for experimenting. Now this quick wood has been in the shop for a couple of years and it is super
dried out, so that was no good, but thankfully I recently purchased some new quick wood, a different
type. I got this at Lee Valley, so we're gonna give that a go. Basically it's a two-part wood epoxy,
you just cut off as much as you need, and you basically just knead it together. And I decided
to experiment and try to put a little bit of pigment in. I've seen some people try to do this
with stain, never tried it with pigment, just thought I would see if I could tint it a little
bit, and I did. I probably could have gone way darker with it and it probably would have looked
a lot better, but I was just experimenting. So I'm just going to push this in and try to shape it.
This is a bit of a process, you want to make sure it's adhered well, so you're pushing it into those
fibers of the pressed wood and then just trying to feather out the sides a bit. Once I get it close,
I just use a flat blade to flatten it, cut off any of the squished out excess, and then feather it
out again. Now these patches have a tendency to stick out like a sore thumb, so sometimes I like
to use the edge of a putty knife to kind of create some texture. Sometimes it works out, sometimes it
doesn't, but it's just something I like to do, especially in an area this visible. I'm not going
for perfection on this one. I also applied some odies to the inside of the drawers, just making
sure that every surface is sealed. I even added a little bit to the plastic wrap. You can put odies
on almost anything, concrete, stone, wood, plastic, vinyl, leather, this stuff is great. Now when it comes
to this piece that was missing, ideally I would have a 3D printer and I could 3D print my own
copies of this, but I do not have a 3D printer, at least at this point in time, so I need to come up
with something else. I've got a couple of things here that I picked up, but I'm going to attempt
to create a version of this. Now this long white thing is used mainly to make jigs for like table
saws, bandsaws, and it basically just slides along that empty track that you see in the front there,
and then you attach something to it. It's basically a soft plastic. I do not have the proper tools for
cutting plastic and it almost kills me to use that saw on that, but you use what you have until you have more.
I did get fairly close with this. This would have been acceptable. I felt like it didn't sit in, I
mean you can see here, I have to kind of struggle a bit to get it out, but I felt like I could do
something a little bit better. So I opted to scrap this material and move on to the acrylic, and I
basically just made a plain rectangle and sanded the bottom edges round so that they wouldn't catch
as they slide along that plastic track. This acrylic tag from Michaels ended up being basically
the perfect thickness. I just had to give this a bit of a tap to get it all the way in, and then I
could give this a test. And that slid nice and easy, no friction, it wasn't catching on anything,
it was the best I could do with what I had to work with. And this is how I made those, I basically
just cut little rectangles with the bandsaw and then used my sander upside down to smooth out the
edges and round those corners over. This will do in a pinch, but I think I am going to look into
some sort of 3D printer so that I can make those pieces myself, because it is a very common issue
with these cabinets to be missing them. So once I had the handles back on, it's basically time to
put everything together. And if we have a peek back at what I started out with, this hunk of
junk was pretty dinged up, marked up, scuffed up, moldy, and was sitting in a dumpster just waiting
to die. And I'm glad that even though this isn't, you know, something super fancy, I'm happy to be
able to bring this back to life, and hopefully somebody can enjoy it. I hope you enjoyed this
quick video that a lot of you requested, and I will see you again soon with a new one. Take care!