โโโโ ๐๐๐๐๐๐ ๐๐๐๐๐ ๐๐๐๐๐๐๐๐๐๐, ๐๐๐๐๐๐๐๐๐๐๐ ๐๐๐๐๐. ๐๐๐/๐๐๐ ๐๐ ๐๐๐๐๐๐๐. โโโโ

Charleyโs Garage
78 followers
2 quality and affordable tools for this job!
Liner height Gauge Link https://amzn.to/4j4o9Cr
Counterbore Depth Micrometer https://amzn.to/403yoxW
Why protrusion and counter bore depth are critical measurements and how to do them.
These 2 measurements are critical for ensuring proper cylinder head to block seal, sealing the water jacket and ensuring the straightness of the sleeve limiting negative wear effect on piston, rings and sleeve itself.
#counterbore #protrusion #sleeve #liner #cummins #international #precision #measurement #enginepower #enginerebuild #diesel #doityourself
Hello, welcome back to Charlie's Garage. Today we are going to talk about
two critical measurements that must be correct when you are
putting together or reassembling a diesel engine and that is liner
protrusion and counterbore depth. So if you are
working with a sleeved engine, one of the things we want to measure is
the ledge that the sleeve sits on inside the block and we want to make
sure that that ledge is straight so that the liner doesn't slope when it's
sitting down on it. We want that liner perfectly true.
So what can happen if we install the liner on a crooked or worn counterbore
ledge? Well what can happen is if the sleeve
is just a you know a little bit off, the piston is still going to try to
travel straight up and down inside that sleeve.
That is going to cause us some big issues with ring wear,
piston wear, cylinder wall wear and it's going to cause
engine failure sooner rather than later. Alright,
the other critical measurement that we're going to talk about is liner
protrusion and that is measuring the sleeve once
it's installed in the block how far up it sits or how low it sits
and the reason why that measurement is critical is because
if that measurement is not within the specified tolerance
you're not going to get a proper head gasket seal when you torque the head on.
So I'm going to show you guys real quick how we
measure those and some tips and tricks okay.
So let's look at the tools that we're going to use.
So here we have two different tools. We have right here
this is called a liner height gauge. Another nickname for it is a sled gauge.
This is going to be used to measure liner protrusion
and then over here we have a depth micrometer set which is going to be used
to measure the counterbore depth. So let's take a look at
what we're talking about when we're talking about counterbore depth.
So right here we have a Cummins ISC. We have one of the sleeves pulled so you
can see this one's got the sleeve in it. This one's the sleeve is pulled.
So this is a wet liner. It's got the coolant cavity around here that's going
to surround that sleeve with coolant to help cool the cylinder
and you have the wedge down here that the sleeve is going to sit on.
So what we're going to be measuring is the distance from that wedge
up to this block deck and we're going to measure that in four
places and that's going to tell us if that
ledge is worn out or uneven. So when we're doing this
the reason why we're looking at it is if you look at that ledge and then you
come over here and you look at the sleeve
right here above this o-ring this part right here is what sits on that ledge so
you can see why if the ledge wasn't straight the sleeve would be crooked.
So the first thing you want to do before you take this measurement
is you want to make sure that that ledge is thoroughly cleaned off.
You can see looking in down in this one that there is some debris and stuff on
this ledge so I would never want to measure this ledge
with that stuff on there because we're talking thousands of inches of tolerance
and just a little bit of contamination on there can make that measurement be
off. So it needs to be very very clean before
you measure. Second thing you want to do is you want to get into your service
manual and find out what your specification is
for what this distance should be. Now that's going to help you because you
have a tool right here like this one that you have a selection of different
size rods that you can put in there. So this is a zero to six inch
micrometer or depth micrometer and it has
availability for different measurements. So if you look
the one that's missing right here this would be your zero to one inch rod
then you got your one to two, two to three,
three to four, four to five, five to six. So by knowing what your spec is that
helps you select which rod to put in the tool.
We have a depth spec of around four and a half inches
so I would want to pick the rod that can measure between four and five inches
long which is the second the biggest one in
this kit. Now the way that this tool is installed in
this one and different depth micrometers are going to be different but this is
pretty standard. This rod goes into the end
of the micrometer like this. I'm trying to do this one-handed
and then you push it down in there and then you
put the cap on. So I'm going to put the cap on and then I'll get back and show
you guys how to use this on the engine to do the measurement.
All right so this is the proper way that we would want to measure it. We would
want the top of this sitting on the block deck and you can see how it's got
spots here for you put your fingers on there
and then what I would do is just rotate it and since I'm holding my phone here
you can't I can't really do use both hands
but I would go down until I heard it click and then
lock my measurement in place and take it out take my reading.
Now these can be extremely hard to read if you're not used to them
because look at this one right here I can see the eight
right that means that I have not gotten down to my 4.8 inches that I see on here
so my measurement is actually 4.7 something
and if I look real close I can see that I
just went past zero so and I see that the hash mark is right
there between the seven and the eight so what that
tells me is that I went past 4.75 I would take three thousandths
right here that's showing on the barrel right there I would take that three
thousandths and add to it so what I got here is a measurement
of 4.78 and I would want to take this measurement in four
different places and that will tell me how straight that ledge is
if that ledge is not straight what I would do is take a special tool that
will take some of this surface material here
off if I take some of the surface material
off then I can make sure it's straight so I could take say 30 40 thousands off
of it and then put a shim that sits on top of
this that will get me back up to the correct height but now it's straight
so that's a counterbore depth now to measure protrusion what you would want
to do is you would want to reinstall your sleeve
so we're not going to reinstall this sleeve I'm leaving it out for training
purposes but so we'll come over to one of the
sleeves that's already installed now protrusion is important because if
this thing sits up too high or too low you're not going to have the right
amount of crush with your head gasket and you're going to develop compression
combustion maybe even oil and coolant leaks
so what we do is we're going to use some hold down tools that are going to
stimulate head torque these hold down tools
get torqued down to 50 foot pounds all right
so you would have one on each side I'm not going to do the whole thing but
because you get the idea you're going to torque these down to 50 foot pounds
once you have those torqued down you're going to take your old sled gauge right
here and you are going to put it on the
block deck now I always hear these people that talk
about the differences between whether I want to measure on and then
off or off and then on it doesn't really matter the distance is
going to be the same so let's do it this way first we got it
sitting on the block deck we got it zeroed and then we just push
it over onto the ledge and we can see right here that we have
about four thousandths of protrusion
okay I could do it the other way right I could start from the ledge
zero it and then move it off and it goes the other way to about four
thousandths again so either way I prefer to zero it on the
ledge on the sleeve and pull it off because
then you're not trying to push your dial indicator onto a raised surface
you want to do this again also in four places
now you're going to find that different engines use different specs and different
ways of determining if you're within spec I
believe this Cummins here gives you a range of like 10 to 48 thousandths of an
inch of protrusion is acceptable but you don't
want any two points that are 180 degrees apart from each other being more than a
thousandth difference and then if you look at an engine like
this international over here you can see that the cylinder sleeves
are extremely close together so they have a spec that says that the
height of this sleeve and the height of this sleeve right here at this point
can't be more than a thousandth difference from each other so it's very
possible that overall if you measure this sleeve in four places it could be
in spec and then you measure this sleeve in four
places and it could be in spec but yet overall you could be out of
spec if you exceed that thousandth of an inch difference between these two
so those are two measurements that you really need to make sure
anytime you're pulling apart putting back together sleeved engines
you want to make sure your counterbore depth is correct you want to make sure
that your protrusion is correct because those are two critical measurements
that if they are not right they can mess up your engine very quickly
so i hope you found this informative i hope that you
watch the video subscribe and like appreciate those of you that view my
videos if you have any suggestions comments or
questions please leave them for me and i will answer them quickly
thank you so much bye
