Overview of the Diesel Heavy Truck Program at Arizona Automotive Institute.

Charley’s Garage
78 followers
Jun 5, 2026
A video I made for our admissions reps so they can talk about the Diesel program.
AI Generated·May contain errors
All right admissions peeps, I'm going to give you a quick tutorial here on the diesel program.
I'm going to walk you through these five classes and kind of give you an idea of what to talk
about when you do your tours and stuff. So the first one I'm going to talk about is course 100
which is diesel engines and fuel systems. So of course the students will go over what a diesel
engine is, how it operates, different types of diesel engines in the classroom and they'll also
have the online environment where there will be modules and electrodes that cover things like
pistons and connecting rods and bearings and crankshafts and camshafts and turbochargers
explaining how all this stuff works. The lab environment itself is after they get an
explanation of how things work is that they'll come out here to these engines that we have right
here in this lab and they will disassemble these engines and learn how to do things on them such as
check cylinder block decks for flatness, all right check this for flatness, how to measure the inside
the bores to make sure they're worn, how to pull and replace cylinder sleeves. As you can see the
students that are currently working on this engine already have all their pistons out
so how to inspect the pistons, replace the bearings, how to test each individual component
as you pull it off so we'll learn how to test oil coolers, how to test the
charge air coolers, tests that you can do on the turbochargers to make sure they're
working properly, even testing like this exhaust manifold that's laying here for flatness to make
sure it's not warped from heat. So they will basically tear this engine completely down
and then as they're putting it back together learn how everything on this engine works
and how to test it. When they get done with the initial first part of this which is the
familiarization and the tear down and reassembly, the next thing they really start doing is learning
fuel systems which includes running engines and diagnostics. So once they get their engines put
back together they kind of go from this lab out to this lab or out to the actual trucks
and these are the engines that will actually start and run. They can do fuel system tests, they can
plug in the computer and get fault codes, they learn how to communicate with the engines, how to
troubleshoot the engines, how to use different websites to find service manuals for the different
engines. So they do a lot of running engine work out here in this part of the lab. So they'll be
able to diagnose, the instructors can actually create faults on the engine for the students to
figure out why the engine is not doing what it's supposed to be doing and by the time they get done
with this course they'll be pretty familiar with diesel engines right. So then once they finish the
engines class and of course as you know scheduling isn't necessarily going to be in this order
but 200 is brakes, suspension, and steering. So if we go down this way I'll take you guys to that lab
but in that lab they got to learn things about hydraulic brakes, air brakes, air brakes in
commercial vehicles are heavily regulated, lots of DOT requirements behind them so it's really
important for them to know and understand this stuff. So are you unlocked? I'm doing a walk
around for the admissions guys so they understand better what to tell students that are potentially
coming in here. So I'm going through each class. All right so this is the classroom where a lot of
the brake stuff is taught. You can see we got boards that simulate the actual air brake system
on a truck so that they can learn what all the components look like, what they do. You can use
these boards to do certain tests and demos. So you got an air brake board there, an air brake board
here. You look over here you've got a hydraulic brake board. So a lot of theory application
testing and a lot of stuff can be done in this classroom on the brakes part.
All right so in the brakes class when they do 200 they're doing brake steering and suspension.
A lot of it's brake stuff right? It's pretty heavy in the brakes? Yeah. And then when they
get done with brakes and you do the steering and suspension you take them out in the actual trucks
do wheel ends. We do wheel ends with brakes. We do kingpins. We do pull springs out. We pull
you know everything off all the way down. Spiders, S cams, everything. So basically almost like in
the engines when I told them we do a complete disassembly and then build it back up so we
know what everything does and where it goes. Same thing with brakes, kingpin, steering,
suspension, all that. All right and then when they get to 300 which is the course I'm teaching
that's basic electrical and fundamentals of heating, ventilation, and air conditioning.
So that 300 class right here basically like it says in the paper that I gave you guys they're
learning basic electrical in this class. Fundamentals of what a diode is, what a relay does,
you know just basic electrical information. How to use Watt's law and Ohm's law. How to do
how to figure out resistance, amps, voltage. Some fundamental training on how HVAC blowers work,
starters, alternators. But they're not really applying this to any truck specific stuff yet.
They're learning the electrical fundamentals and then they'll start applying those electrical
things they learned in 400 and 500. Actually we do the in the 200 or 300 I mean whatever AC left
was. We do starter removal replacer, we do starter amp draws, we do battery draws, we do all that
stuff in that class. Right so basics but putting it all together in an overall view would be like
a PM thing and a chassis electrical and all that right. We teach them multiplexing and how important
that is. All right so the basic electrical does kind of go well with the heating ventilation and
AC because that's a heavy electrical type setup there. The way fan clutches operates and climate
controls and stuff like that. As part of the HVAC part of the 300 course they're also going to be
getting their 609 refrigerant handling certification and they'll also learn the basics of HVAC such as
the cycle of life and how the air conditioning system actually works.
And then when you get to the DT400 you've got diesel drivetrain and chassis electrical. So
the diesel drivetrain is basically going to cover everything behind the engine. You have an engine's
class now you're going to tie it into how that power goes from the engine to the wheels. So
transmissions, clutches, torque converters, automatic transmission, standard transmissions,
driveshafts, u-joints, pinions, rear differentials, all of that stuff is covered in the diesel
drivetrain class. And then the chassis electrical in 400 would be controllers, brake modules,
computer modules, multi or can networks and multiplexing and stuff like that right? No,
no it really doesn't teach on our stuff that's the electrical. Okay so that's after. All right
and then what's in electronic systems and PMI then? Yeah okay I'll just cover everything again
and we put it right. So as you can see we got three courses in a row where there's going to
be some electrical training going on there. So and then there's also electrical stuff in the
first two classes the 100 and the 200. So a little bit so one of the things that they're going to get
a lot of over the all five classes is there's going to be some electrical stuff in all of them.
The big thing about the 500 class is the preventive maintenance inspection.
PMI is a big part of diesel technicians job, meeting DOT requirements, safety of the truck,
those are big things that we spend a lot of time making sure they understand what's safe,
how to tell if it's safe, how to tell if something's out of adjustment, how to tell
something isn't going to be kosher with the DOT inspector, how to properly document this kind of
stuff. So all that is part of the program. So I'll take you out real quick and let you see the last
lab we haven't looked at. It's mostly drive train stuff out here in this lab. So let's go take a
look at that. All right so this is our drive train lab. Get the lights on it's kind of dark in here
but as you can see from all these transmissions right here this is like I said everything behind
the engine right. So if you've got a standard transmission of course you're going to be
transmitting power from the engine to the transmission via a clutch. So we'll teach
them everything they need to know about clutches, how to install them, how to adjust them, how to
maintain them. All right and then they'll actually something that they may never get to do in the
field but we'll get to do here at school is completely disassemble one of these big
transmissions, figure out how to set up the gears inside of them and so forth.
Then once they learn the transmissions they'll even get to practice removing and installing
transmissions on the actual training aid right here. So we got a transmission mounted in this
engine, practice removal and reassembly, adjusting the clutch afterward. We got labs that go over
air operated clutches and how to high range low splitters and then of course you got after you
leave the transmission you have drive shafts and u-joints and stuff which we mostly teach
out there on the actual trucks. Then after that we come back in here you can see there's a bunch
of different differentials. We teach them things about the differentials, how to adjust lash on
them, how to inspect them, replace them, keep them in shape plus transfer cases that might be used for
multi-axle drive lines. So a pretty in thorough in-depth program here. Everything is covered
from bumper to bumper on the truck and we are working on introducing hydraulics into the
curriculum again and hydraulics will probably find its way into the 300 course between electrical and
HVAC but that's something that's on the horizon. We even talk about PTOs you see this PTO mounted
on the side of this guy right here. So hopefully this helps you guys out a little bit lets you
kind of know what we do in the different classes, the water we do it in or the water the classes
are lined up in. But like I said there's very few prerequisites on this sheet you know so
my three new students that I got right now are in 300 which is basic electric and fundamentals
of heating ventilation and air conditioning. So they could start at 100 they could start at 300
it all kind of depends on what class is available and who's available to teach it at the time new
students start but there really is only a couple of prerequisites here. We wouldn't expect someone
who hasn't been to the other classes to know how to PMI a whole truck if they haven't been through
the individual classes learning about the different parts and stuff. So if you guys have any questions
at all during a tour always feel free to bring the students by to talk to me or prospective
students by to talk to me. Also any of our instructors are also willing to talk to prospective
students. So our goal is to help you get more students in the door so if you need help just
let us know.
