๐๐ก๐๐ซ๐ ๐ ๐๐ข๐ซ ๐๐จ๐จ๐ฅ๐๐ซ๐ฌ (๐๐๐)! ๐๐ก๐๐ญ ๐๐ก๐๐ฒ ๐๐จ, ๐๐จ๐ฐ ๐ญ๐จ ๐๐๐ฌ๐ญ ๐๐ก๐๐ฆ.

Charleyโs Garage
78 followers
link to test kit on Amazon: https://amzn.to/4h0OG1q
If you buy this kit from this link I get a commission which helps support this channel so THANK YOU!
In this video we cover the basics of Charge Air Coolers, sometimes just called the CAC. We cover what they do, where they are located and how to test them.
#diesel #CAC #Chargeaircooler #UTI #universaltechnicalinstitute #caterpiller #CAT #international #Frightliner #peterbilt #cummins
All right so today we are talking about charged air coolers and what I want to show you guys
is when your turbocharger compresses air and creates boost to send into the engine
it also heats that air up tremendously and when air gets hot it expands so if I were to take the
air coming from this turbo and send it directly into the intake manifold that air would be so
hot entering the combustion chamber that the oxygen content would be greatly reduced and
oxygen of course is a key component to combustion so in order to keep the boost pressure that we
want to pack the cylinder full of air but still have the oxygen rich air we have to cool the air
down after it's been pressurized and that's where a charge air cooler comes in so you look at this
turbo and we follow it you can see the tubing comes up here to this guy right here so if I
come around to the front we can see that you know you have your radiator and if this was in a truck
with an air conditioning there'd be condensers and but then this one right up here the top piece
is the charged air cooler and on some engines if we look at this one that charge air cooler is that
big silver thing in front of the radiator so that's usually where they're located up at the
top of the radiator below the radiator or right in front of the radiator are the most common places
so if we come back around to this side we see that coming out of the charge air cooler
that the piping goes into the intake manifold right so the reason we use the charge air cooler
is to increase air density right that's the key purpose so that there's more oxygen in that air
when it gets to the cylinder all right so if you look here you see we got a couple of charge air
coolers sitting on this table here and then attached to these charge air coolers we have
plugs in the hosing so here you can see one that's just got a valve on it and then over here is one
that's got a air connector on it for us to pressure test them so what we do is if we suspect
that we have a leak in a charge air cooler we can hook an air hose with a regulator of course
up to this side and then we can make sure that that valve is closed and we're going to put about
30 psi of air pressure in it and then we watch it for about 15 seconds these are not designed to be
completely leak free so they have a leakage specification that is usually depending on the
oem somewhere between 5 and 7 psi allowable loss so if i put 30 in it and after 15 seconds i still
had 28 psi i would say that that's a good charge air cooler that's not leaking so that's how we
test these charge air coolers in the shop is we'll do the pressure test like that and you can see of
course that these guys have safety chains if the clamp holding that cap on here wasn't very tight
30 psi doesn't sound like a lot but if this guy decided to pop out of there it could do
some serious damage so for safety reasons when you do this test you always want to make sure
that one of these clamps is attached to something that's going to keep that thing from flying too far
so now we have the test equipment hooked up to the cap so you see i'm using a regulator right here
we've got a pressure gauge so we can read it and then you've got the valve so anytime of course
when you initially hook it up you want this valve to be closed so i already made sure though that
this was backed all the way out to zero psi and then i open this up and then you use the regulator
to increase to your 30 psi all right so at 31 is okay so i shut this guy off right and we can see
it's already dropped to 25 going down to 20 so that would be an indicator of a bad one of course
mine's leaking because the connector here needs to be replaced which i'll take care of later
but if you were testing one that had good connections and it leaked down that fast
after you supplied the 30 psi that's how you would know you have a leak in that charge air
cooler and know to replace it i will tell you however that one of the reasons why we like to
run the test on the end of the original hoses that are on the truck is that these expansion
bands that are on these hoses these hoses are not intended to be like a long-term piece they're
considered expendable the items that wear out need to be replaced commonly or frequently so
when you're testing it like this and you use the original hose not only are you testing the
charge air cooler but you'll also find out if you have any kind of leaks around this guy and if it
needs to be replaced general rule of thumb though i usually do is that replace these whenever they
come in for this kind of work anyway but you can test these at the same time
