In this video, I'll do what I can to bring a damaged and neglected art deco-esque storage chest / trunk back into great condition. Veneer patching, repairs, and replacement, adding more structure to the drawer bottoms, re-staining the trim wood to match the beautiful walnut veneer, and more. None of these repairs are considerably complicated, but they ARE time consuming. Hoping you enjoy this furniture makeover!
Angie restores a damaged storage chest featuring walnut and mahogany veneers. Despite poor original construction and significant veneer loss, she stabilizes the piece through strategic patching, chemical stripping, and structural repairs, ultimately reviving its aesthetic appeal and ensuring safety through hardware modifications.
This video is sponsored by Craftsy. In today's video I'm going to be tackling this little
storage chest. Now somebody gave this to me about five years ago free of charge. They didn't want
anything for it. They just wanted it to go to a good home. Unfortunately it has been in storage
for five years and I'm only just now getting to it but this damage had occurred prior to that.
You can see we've got some pretty good veneer damage on the sides. The back is missing most
of its veneer. There's a lot of ripples and cracks in the veneer on the top. The drawer
needs a little bit of work but the inside is actually in really good condition with the
exception of this extra knob for the drawer and the pieces of the one that's currently on the
drawer. So at first glance you might think this is a cedar chest because of the way it's not
finished inside but this is actually mahogany veneer. The outside is walnut veneer. Let's see
what we can do with this. My name is Angie and I refinish furniture. Sometimes I paint and sometimes
I don't but I always do what I can to save old pieces from the trash. Welcome to my workroom.
Chests like this are pretty common on Facebook marketplace especially the cedar ones and
unfortunately most of them are in a condition similar to this but for me they are really fun
to work on especially with the beautiful veneers they used to use on these. I have a long road
ahead with this one though. Now this piece is not amazing construction. The majority of this is put
together with nails. There's no fancy joinery but again they do use a lot of beautiful veneers.
Unfortunately the back panel of veneer is completely gone and the rest of the veneer has some issues
whether it's finished damage or some rippling. The side panel is going to be a little bit hard
to get at because I can't take the trim off so I'm gonna have to figure that out. You can also
see the nails go right through the outer veneer. Super strange construction but it is what it is.
I'm going to do my best to make this look nice. I'm going to get to this veneer repair in a little bit.
I'm going to start by removing the finish. I'm going to be doing a combination of scraping and
using a chemical stripper. One of the most common questions I get asked is why I use one and not
the other in certain situations. For me scraping is easier, it's faster, it's less messy, less smelly,
no chemicals and on a finish like this that is very frail and flaking it's my preferred method.
Keep in mind though that even though you get little piles like this there's a lot of
very fine dust that kicks up when you scrape this kind of old shellac finish.
So you definitely want to be wearing some sort of mask or respirator. There are some considerations
though when scraping especially on waterfall furniture like this. This edge if you're going
a little too rough sometimes you can catch that. These scratches against the grain you
have to be careful with too because if you're pulling down with the grain and you happen to
catch it you can tear the veneer especially if it's lifting a bit from its substrate.
You want to go super careful around the edges as well. Scraping isn't difficult but it does
take a little practice to get the hang of it and kind of finesse it. Now this mahogany veneer is
in really good condition which is shocking considering the outside of this piece. So I'm
doing just a very very light sanding just to kind of clean it up. So I'm doing 180 grit sanding here
you can see right in the middle of that horizontal scratch it's still there. When sanding veneer you
have to be so careful so what I always recommend is don't try to get every scratch out with your
harshest grit. Do your first grit, your second grit, third grit and by the time you get to your
final grit it should be out. If you go too deep with your first grit you'll never get those scratch
patterns out and it can be quite a mess. Generally any edge where you have lifting veneer if you go
all the way along the edge you're going to find more so I'm going to repair all that at the same
time. But I want to show you this drawer bottom. They're pretty messy. There's some staining here
they're dipped in the middle and it looks like someone may have tried to refinish this before
because they've burned through the veneer with a sander probably to try to get some of that
staining out. I'm not going to fully replace the drawer bottoms but I am going to fix them up a
bit. This knob is really unique it's made of a bunch of tiny pieces and it is so brittle there's
no saving this. So I am going to have to replace the hardware on the drawer. Going back to the
construction of this again I mentioned there was nothing really fancy about these and these drawer
bottoms are no exception. Normally the drawer bottoms are slid into slots on the sides of the
drawers not in this case they are just nailed to the bottom all the way around so I need to
carefully pry them up and pull these nails out to get the drawer bottoms off. I always like to
clean up the drawer boxes themselves on these old pieces it just looks so much nicer in the end.
Now these are the drawer bottoms um I'm not going to be having this mahogany exposed it's too rough
for me but I am going to cover it with new veneer. Now I don't have any mahogany veneer so I'm going
to have to use walnut on the top and I'm going to use some maple on the bottom. This is going to do
something other than just make it look nicer it's actually going to help stabilize it. You can see
there's quite a big bend there. I'm actually going to add some water to the side opposite the bend
and clamp these together let them dry and hopefully that will reduce some of this a little bit and
when I go to put the thin veneers on it's going to go just like plywood the veneer I put on is
going to go perpendicular to what you see here. This is going to help give it structural strength
and I think it's going to save me from having to buy new drawer bottoms. Now really I could just
paint the back of this it's the back no one's ever going to see it. Veneer is also really expensive I
don't know if you've ever bought veneer or bought it recently but it's not cheap but I am going to
replacing the veneer on the back panel. Now I don't have any normal paper backed walnut veneer
but I do have some of the 3m backed veneer. Now just the sound of that probably makes some people
cringe it sounds like a cheap product. I've used this many times and in situations like this it's
going to work out great but before I get to that I'm going to deal with some of the structural
issues here on the bottom. A lot of the bottom was so loose I could literally pry it off with my
fingers and again it's because it's basically attached with nails. There are a couple of glue
blocks there but the glue has failed and there's actually quite minimal glue there to begin with.
I'm going to clean it up and put it all back together. Now on the sides and front I'm going
to be using a chemical stripper. Sometimes when you have veneer that is in 15 different directions
like it is on the front scraping can be a little bit tricky and even once you get used to it it's
more time consuming so a stripper is going to make quick work of this old shlack. Now the wood
on the trim and the leg assembly is not walnut it's a very pale wood. It doesn't really matter
what it is it's going to have to be stained. I could do kind of a contrasty two-toned look
and probably wouldn't be a bad idea considering the rest of this piece is all brown but I think
I'd like to keep it like it was with the dark base. This too is not in the best condition
because the glue has failed in the joints which you can see there's hardly any glue there at all
so I'm going to reattach these shore them up again with some wood glue put the nails back
in and then put it back on to the base. When you have mitered corners on older pieces like this
and you put fresh glue in the joint I like to just kind of sand around the edges. I don't need
a crisp joint here but the little bit of sawdust will mix with the glue and make it look like it's
a better joint than it actually is. There was a split in this drawer so I glued and clamped that as well.
So this is the 3M backed walnut veneer that I'm using for the drawer bottoms. This will be on
the top and then this maple will be on the underside. Now you can see here how I'm doing
it perpendicular to the grain that's already there. This is really important with veneer and
it's how it's going to help flatten this out and make it just a little bit stronger. This is
literally how they make plywood and why it's such a great stable product. It's peel and stick and it
adheres with pressure so I'm just using a burnishing stick here and then trimming off any edges. This is
the company that makes the veneer that I use. I do like this. I don't always buy adhesive backed
veneer but in situations like this it's a great product to have around. What is nice too is that
if you position it and it's just slightly off you usually can peel it up once or twice without
kind of sacrificing the adhesion and put it where you need it. Using something like a contact cement
you get one crack at it because as soon as those two pieces touch you can't move it so
that's why I do like it in certain situations. There is one consideration and that is that part
of this has to slip into a small groove in that bar that separates the two halves of the drawer
bottom. The extra veneer makes it so that it doesn't actually fit so all I did was pull a strip
off and you can see now that it will slide into where it was. So here is the drawer bottom. I don't
mind the walnut. I feel like the mahogany would have looked better but I didn't have any so I did
what I could. Now just before I get into these veneer repairs here I want to say a quick word
about today's sponsor. Craftsy is an online community and resource for all things creative.
People who make, people who bake, crafters, DIY enthusiasts, and even more recently some
woodworking stuff. You can watch on your computer, you can watch on your cell phone like I'm doing
here. Some classes and videos even have bonus content like this particular class here. You can
actually download the plans for this shop cabinet, measurements, cut lists, and that comes included
in your membership. The classes are broken down into really easy to follow lessons and are led by
really accomplished and talented people. They're always adding new content and there really is
something for everyone here. I love dinner rolls and these look amazing so I'm definitely going to
have to try these this Christmas. You can search for a class to watch by video topic, by instructor
if you're looking for someone in particular, by video length so if you have a certain amount of
time to spend, or just browse the new arrivals section until you see something that looks
interesting. This stained glass quilt is beautiful, that's really cool. If Craftsy is something that
you've been considering trying out but you just weren't sure where to get started, the first
1,000 people to use my link in the description below will get a full year premium membership
to Craftsy for only $1.49. This is for new members only. This is the perfect time of year to try
something new. So back to the project at hand here. Now this veneer is super brittle in spots and
so now I need to find some patches for these areas on the back. Looking at a piece of veneer
off an old piece, you can see there's a huge difference in thickness between new veneer and
old veneer but what's actually happening here is that the veneer, that very thin strip, is attached
to a substrate. The two are one basically. This can sometimes confuse beginners who think that
the veneer is super thick but it's actually just attached to a substrate. So I think I'm going to
make my patch with this old piece. I'm going to remove the finish so I can check out the grain
and the color. I think this is going to be close enough. Now I am going to peel the veneer off of
the substrate because there's already a substrate here on the top. The first thing I'm going to do
is change the shape of these broken pieces a little bit and you can see it's so brittle it
just wants to keep breaking on me. It's easier to make a patch with a straight line than it is a
crooked line in most cases so that's why I'm making it a little bit wider. Eventually it's
finally time to glue these pieces down. I could use hide glue or something like that. I want a
permanent bond here so I'm just using a regular wood glue. Veneer repairs like this can take a
while but I always try to tell people to take your time. Don't try to rush through it or you risk
having to fix more damage. I'm using some painter's tape to apply downward pressure to this and while
that's setting up I'm going to go ahead and put my patches in. Now this part went a little bit
sideways on me. Normally I would have just popped the trim off the bottom and you know with a glue
syringe or spatula kind of stuck some glue up underneath but because that trim wasn't easily
removable I had no choice but to actually remove the veneer and even heating it up it was just
coming off in flakes. It was so brittle so I'm actually going to be replacing the veneer on that
side with the same stuff that I used to make the patches. The grain on the side is vertical so I'm
obviously making sure that that's what my replacement will be and just like the side, how it
was in multiple sections, that's what I'm replacing it with. I just need to figure out what orientation
looks the best to me. In this situation I decided not to remove the veneer from its substrate like
I did on the patched areas. It is going to make it a little bit thicker on this side but once
everything is said and done it's not even going to be noticeable. Eventually it's time to take
the tape off all of the areas that were glued, clean up those spots a little bit, and now I can
clean up these patched areas. You'll see there's still one small little hole that I didn't bother
to put a piece of veneer in. I'm just going to use a little bit of wood filler there and also
around the patched areas. My patches were pretty tight but the filler just kind of helps make it
seamless. Now these two water spots on the top here, this is something I almost never do. Normally
with oxalic acid you apply it to the entire surface. Because these stains are so irregular
in shape I'm actually just applying it to those. I'll let it dry, rinse it off, and then hopefully
they'll be gone. Now I'm using that same 3M backed veneer that I used inside the drawers
on the back here to replace that huge missing panel. I'm using Ceman water-based stain to take
care of all of the light wood. That's the leg assembly, the trim, and I'm going to rub a fair
bit of it off. I want this to look a little bit aged. For the interior I'm using some Odie's oil,
universal oil mixed with a little bit of their safer solvent. This is going to give me a little
bit of a thinner consistency. It feels kind of like a Danish oil in a way. Now if you're wondering
why I'm sealing the inside, remember this is not cedar, this is mahogany that they left unfinished
to kind of mimic cedar. It doesn't have the same aromatic properties that cedar has so there's
really no point to it being unfinished. I think mahogany with Odie's oil is a beautiful rich glow
and that's why I'm opting to seal the inside. There's no worry about the Odie's oil transferring
to clothes. If you've been around my channel you know that I use this stuff all the time.
It gets applied, rubbed into the surface, left to sit for a little bit and bond with the wood fibers
and then all of the excess oil gets buffed off. All of it. And once it's cured it's a lovely
durable tung oil-based finish that I absolutely love and prefer to use wherever I'm able to.
Once everything is completed it's time to put the hinges back on. You remember I added veneer
to the back so I have to re-punch through into those original holes which is actually pretty easy
if everything lines up. I did clean the hinges and screws up with a little rust bath
and I'm just adding a little bit of flitz polish to that copper opener. I'm not trying to get all
of the tarnish off but most of it. Back to the handle situation. These were obviously a no-go.
These are some wooden ones that I had. This one I think is a little too big.
I do like the shape of this one. It kind of has that sort of art deco-ish vibe but again I find
it just a little bit too big. Everything on this is brown and I thought maybe a little pop of
something brighter or shinier would be nice. So I have these brass colored holes that I think
are going to be perfect and just add a little bit of bling to the front. Now we have to talk about
the lock. This is not a lane cedar chest and for some reason people always equate the issue with
locks with lanes specifically because they were the ones who started the recall on all of these.
In some places it is illegal to sell a chest with a lock that cannot be opened from the inside.
You legally have to either remove the lock, replace it, or disable it. So all I'm doing is
taking this top section out. It's kind of a drag because I love how the lids latch down but it is
a danger to children and pets if it locks and cannot be opened from the inside. So I'm adding
a little patch of decorative veneer over that where the holes were just to kind of tidy it up.
Once the glue had dried I was able to trim the edges up to fit that perfectly and then added
a little bit of odies oil there as well. And yeah let's have a look back at what I started with.
This piece was quite a mess. It had obviously a lot of water damage from over the years,
failing a flaky finish, alligatored in some spots,
missing in some spots, damage to the bottom drawer, loose and unstable joints, a lot of
rippled veneer, and the back panel is missing all of its veneer. I hope you enjoyed this
transformation. As always thank you so much for watching. If you like this sort of content don't
forget to like and subscribe. Leave a comment down below let me know what you think of this
transformation. See you next time!