My American Dream is ONE Step Closer!!

Screw Driver
87 followers
#car #automobile #business #consulting #salesagent
Buying this vehicle is an exciting start to my journey here in the USA. Like everything it came with some problems, nothing I can't work through however. Since this ford shape was released I've always loved them. I am so happy to finally have one!
I hope you all enjoyed the video. Thanks for watching ☺️
AI Generated·May contain errors
A bit of gas leaking is no issue and there's a fire over there whatsoever.
Right Frank? Right.
Hi guys, welcome back to my channel and welcome to my new F350.
This is an XLT and I think it's like an XLT Premium or something someone said to me.
I don't quite know because I don't really understand all the models
but this is a lot higher spec than most of the XLTs I've seen for sale online
and I'm really pleased about that.
So that was kind of one of the reasons I bought it,
because I was looking for something even higher
but I think the only thing this hasn't got really is leather seats.
So a bit disappointed about that but I'm happy about everything else.
I am actually videoing this video after doing all of the work to this
so this isn't actually done right now
but in this video you're going to see a lot of issues that it had
because there was loads of stuff I had to go through
which is why this is quite a long video.
So I hope you'll enjoy it and without further ado let's get on with the video.
First things first with my new truck I want to fix a couple of problems now.
This is not a bad spec it's an XLT which it's kind of like a bit of a mid-range spec I guess.
It's got like all adjustable mirrors obviously and automatic lights.
It's got rear work lights in the bed.
You can adjust the pedals on it here which is pretty neat.
Another thing it's got is telescoping mirrors which are for towing so that's quite handy
but what the issue is is actually with these mirrors
now as you can see that one goes in and out but I'm pressing the button
and this one on the right doesn't go in and out.
The previous owner before I bought this admitted that he hit something with that mirror
and that mirror is an aftermarket cheap one.
Now it's got all the electric functions and every other light function there
but it doesn't work properly so it doesn't it doesn't fold in like this one does.
It's just stuck there so I have the original mirror and I'm going to take it apart
but before I do that I'm going to take this one off as well
and we're going to see if we can make one good one out of the pair of them
and hopefully it saves me a thousand dollars because they are really expensive these mirrors.
Because it's so cold outside I've decided to come down here to my grandpa's workshop
and unfortunately if something you might remember but he died maybe like 10 years ago
and or actually it wasn't far off 10 years ago it's 10 years ago in a few months time
I think six months but this is his workshop and it's still got everything here like
this old drill and I actually used this drill maybe a couple of weeks ago which was hilarious
but what I want to do down here is strip this mirror down and see what parts it needs.
Obviously there's a big hole in it here so it needs this whole back cover
and there's this piece missing which is this piece was the external air temperature sensor
and then this piece is a is a light which you can turn on in the cab by a button
so it sort of lights up down by the side of the vehicle it actually works really well it
creates like some sort of spotlight sort of thing there and it just makes it really easy to see
so I've got one of those already but this I'm missing that little bit though that I'm missing
uh is the air pressure sensor as I said or external air pressure temperature sensor even
and the sensor itself was like 23 bucks something like that it wasn't expensive
but this plate which is one inch square roughly just to hold the sensor in place was something
like 54 dollars and I was like completely alarmed at how expensive that was I'm going to strip it
down anyway and let's see what's broken you can see me here removing one of these six screws that
attach the back cover to the thing I actually I think it was seven screws but that's me removing
them and then once you've removed them there's a load of clips which you have to hold a little
bit of tension on and then you can just unclip them it's a real pain though and it's really
fiddly to try and do it but it's pretty simple to try and get this off unbelievably that's the
little sensor that I was missing it's somehow blown itself off and up the back there so that's
good um this kind of seems like the only issue with it was the hole in it right now I mean there's
broken tab right there but that's screwed on the other screw that I haven't taken off
something worth noting is the weight difference between this one and the old one which on the
bench obviously where it's not telescoping it's so much heavier or so much lighter sorry
but what I'm going to start with doing is stripping the old one first see what it needs and
then hopefully I can sort of borrow the bits out of this one to make one good one out of the two
so like the other one I need to take these mirrors off first
hope I don't break them so I'll be right back once I get these mirrors off because
these are not as good as the other ones so I'm going to try and make this short and sweet but
this is the one that was on it this is the non-genuine mirror and as you can see there's
the light there which is a blind spot light and you've got the hole on this one but there's
the sensor here which is the external temperature sensor what I've noticed they've done is they've
and something else I also noticed is this mirror is I think they're screwed from behind whereas
this one's got like a clip mount there as well as I think the two mounting holes with slightly
different positions up there so I don't really want to take the chance and try and sort of break
this mirror to get it out and then it not work because then I'm I've got neither mirror and I
don't want to spend 400 bucks on just a cheap mirror because I think that's roughly what that
was and then the other thing is this glass here I'm not sure if you can see but there's a light
at the like that detects vehicles by the side of me and it's causing an issue because this one
doesn't have it it's showing um amber lights on the dash of my car um that the sensors are not
working but it's just the fact that this isn't connected because I just tested it all and this
works completely fine um so I'm going to see if I can find a mirror that's got damage to the front
face here rather than the back like my one's got and if that is the case then I can just replace
it and it shouldn't be too bad then but everything else on this mirror looks okay and it all worked
okay when I just tested it so fingers crossed fingers crossed I can buy just a spare mirror and
make good one out of the two and then sell this one as a good used mirror I'll come back to the
mirror later on and how I fix that but for now let's get on with something else the reason I've
just bought my truck inside is because I need to unload these toolboxes that I bought now um these
are called pack rats and they're made by weatherguard and they're quite a nice toolbox
I think there's some stuff stuck in the rollers or the bearings might be bad but I'll fix those but
I got the pair of these toolboxes and they fit quite nicely up against the side here which is
kind of what I wanted to do I wanted to I might not even need the second one but they just fit
nicely against the side and they leave a lot of bedroom still for me which is kind of what I
wanted so because I can't lift those on my own I'm going to take the drawers out so I can move them
and then hopefully clear the stuff out inside to remove the drawer is really easy there's two
plates on each side and they're two half two half inch bolts in each one of them and then
they just slide out and then I mean I couldn't really see how these are made a line but there's
four little bearings at the end of the roller there and the bearings have gone in that roller
there I can see um but I'm going to move these out of the way and then do the bottom one same
again it's really easy just unbolt those two plates and then you can lift the drawer straight
out and the drawers are much lighter when you do do this the last thing to take out now is the
fifth wheel so for my UK and European followers that haven't seen these before um this is pretty
much exactly the same as well I mean they're different but they're the same thing as like
what I used to use in the UK on my truck what's nice about this setup however is that I've got
the fifth wheel here for like campers and RVs and stuff not RVs but the big campers that they have
and then just behind here is the normal fifth wheel for like the normal um I think they call
them deck over trailers um so you can put that on there and then essentially it's just a ball
out of the floor um but I'm gonna take this out now and then go and get what I need to get
this fifth wheel mounts really nicely so there's four little pins that normally hold it on
but it would normally be sat between those two long steel plates but at the moment I put it
on the back one just out of the way so it wouldn't rattle and move around while I was driving
so yesterday one of the reasons why I took my toolboxes out and the hitch out was because
I bought myself a tub for it um because that rubber mat was just allowing loads of rubbish
to fall in there so I've unbolted these hitches with great difficulty because I don't have all
the tools and I'm going to lift them out and then I'm going to put the bed in and I don't think I'm
going to refit them at the moment I'm going to keep them just so I have them but I don't they
just create so much dirt in the bed and unless I actually need a fifth wheel which I'm not sure
about at the moment I decided that I think it's best to just keep them off and keep them with the
kit because like I'm going to leave the other mount in there so all I need to do is literally
just cut some holes in that refit them and then just pin it back in place so I think that's the
wisest thing to do so I'm going to do that right now unbeknown to me when nothing's been done at
my grandparents house since my grandpa died all of the hoses had holes in them so they were just
like sprinklers so I had to just keep filling up buckets and running backwards and forwards to clean
this bed out ah just finished I think I did maybe like 10 buckets with the holiest pipe ever
imaginable that pipe had more holes than a bloody pin cushion it was terrible but I've cleaned out
the bed now and I'm going to try and fit the bed liner now I don't know if I need to remove these
cappings I hope not because it doesn't look very fun to take them off this thing was really
so difficult to try and get it under those cappings without removing them I'm not sure
if there's a specific way to do it or not but like doing the one side first seemed to work well but
then once you got to this end bit here you just couldn't pull this the tension up to try and get
it under so I was a little bit barbaric as you're about to see but it went and nothing got damaged
so it worked and that's all that matters I've got it all in and I'm going to cut this up or
I'm cutting this up the floor mat as something to lay on if I want to work on my back or like
working on the floor or whatever so I thought it'd be handy just to keep as like a laying mat
or crawling mat essentially I also think there's like a clip that's meant to go in there and on
the other side so I'm going to see about what's missing from there and the little cover for there
stop stuff like debris all going down in there because it's going to fill it up but yeah I'm
just going to put my toolbox in the back and then I'm done for the night one of the last things to
do to this truck is and it's the parts that I've been waiting for the fuel cans are a sign of what
it is but there's a it's quite a common issue with these that the fuel pump has like a non-return in
it and the non-return breaks down I think over time so you have to put a new fuel pump on it
luckily it's gas so it's only like it was like 220 bucks for a fuel pump but we've got to take
the tank out to get to it so first things first got the old 30 mili package and obviously there's
ice on the floor which is brilliant but I've got to take all of these bolts off here for the
under tray here and then once that comes off I can get to the tank electrics and everything
so I've got this I've got this fuel line off just need to take this other one off there's
like a little tab that you've got to pull out there and then you push this in the old secret
handshake fuel line delete package oh there we go all right what next Frank off I don't know help
so Frank and I over the last couple of hours probably have taken off these fuel lines here
which was increasingly unbelievably difficult and then where it got more difficult was the two
electrical connections that are buried back here but you've got to be even more of a contortionist
than all of the other things to get out and now Frank is just dropping I don't know what I'm
because we did this one already so Frank was ingenious managed to get these off there
um a bit of gas leaking is no issue and there's a fire over there whatsoever right Frank right
that's it there do a little bit there okay that'll do well YouTube and Google are still
hammering me more than Thatcher hammered the miners but if you want to see more of my regular
updates make sure you head over to my Patreon channel where I've been posting much more
frequently on there and there's a lot of big life updates which will answer a lot of your
questions I'm sure all of the support that I've been getting throughout that throughout this time
period has been greatly appreciated so thank you all for sticking by me with everything that's been
going on you just put on the high speed package to lower it yeah can you pick it up with me
get it yeah I need you to pick it up
don't you tell me
we've spent hours on this today and annoyingly the fuel pump that the shady Napa dealer guy
sold me is completely wrong so we've got to put the original back in and then next week on
Tuesday or Monday I can go and pick up a Delphi one or a Delphi one as they say out here
and I'm just going to refit this and we're going to have to reuse the seal because I don't want
to take the seal off of that but we're just going to grease it so hopefully it doesn't cause a
problem I said dodgy Napa dealer there for a reason because when I ordered it I asked him
that I wanted a Delphi one or a Delphi depending on how you want to say it and as you can see on
the top right of the screen that's exactly how I got it just in a clear plastic bag there it's
almost like he bought it off eBay just to sell it to me like that and make like a quick buck on it
rather than actually getting me specifically what I wanted and what I told him I wanted
so Frank and I have put the tank back in we're not going to put the plate on because I'm gonna
have to take it back off again when I get the right pump but it only took about like 10 minutes
15 minutes to put it back on maybe 15 20 I'd say it wasn't that long so hopefully it won't be
too long to do it on my own the next time the truck's running now so that's good
so what I'm going to do now while we're outside I'm going to fix these straw runners
so what the issue is with these is the rollers are terrible that they come with and they're
like 60 or 70 bucks for the rollers now there's one in each one of these but what I found was
that I can sort of make do with just a load of bearings so I ordered I ordered so these 30
bearings two shafts and this little clamp collar set that I found online I think it was about
50 bucks something like that for the whole thing whereas one roller one of these crappy rollers is
60 bucks and I need two of them or 60 something dollars so this should hopefully fix both of them
for 50 roughly so this is the roller and it's got like bicycle wheel style bearings in them
where they're just loose ball bearings and then as you can see what happens is they fall out
I did speak to Sam about this as well and he said that he bought some new rollers and they
immediately sounded bad so I think the old bearing package in there should work a treat
because I was trying to do this quickly I just used the vernier here to mark
the end point of where I wanted to go with the machine on so at least I had like a cut point
where I needed to finish up to and then it was easy just to make each pass up to there and then
I did one last finish pass just to make it really quick and simple for me and it didn't take long
at all to do this now the bars will turn down I just need to grind about 0.75 of a mil off each
side just so it'll fit in there and it'll lock it in place in the end what I did was I just used
a file the edge of a file so hopefully just got one more to do now and then we're done I'm going
to do that later when we put the heating on in the garage because it's freezing right now
I finally got the replacement fuel pump so I just had to quickly take it back out again
now this was a lot easier this time because a it wasn't like minus 10
celsius which is I can't remember like five degrees fahrenheit or something but also b it wasn't like
everything was in a better position because the hose clamps for the filler neck and everything
like that were all in such an awful position so frank and I managed to put it in a place where
I could actually get to everything the new pump is finally on and that's the right one so let's
put this back in because of how heavy I remember it being with frank I decided to leave this
literally on fumes to the point that I was concerned that I wasn't going to get to a fuel
station but at least I was able to then move it myself and get it in and out and off the
jack as well because you have to lift it off the jack to be able to get it from underneath the vehicle
somewhat surprisingly I think I managed to do the whole thing this time in maybe about 15 minutes
maybe slightly longer but it really didn't take me any time at all and I think part of that is
because obviously frank and I had adjusted everything so I could get to it but it really
wasn't that bad doing it for the second time and not in the cold that we were doing it in
previously because that did make everything a lot harder we're a couple of weeks later with the
mirror and I've got the answer to my problems and that would be this one so this is exactly the same
mirror but it's just got a silver bezel on the corner there and everything works on everything
works on the other one because I just went and checked it so I'm going to strip that one down
and make one good one out of the two and then because that one's already damaged on like this
bit here or further back there I'm going to put that cover on that one and then resell that one
because that one still completely works fine but it's just got broken plastic so it'd be a cheap
mirror for someone if they needed a motor or like this bit because all of those bits are
really expensive so I should be able to get my money back hopefully and fixing this might not
cost me anything at all fingers crossed I didn't show it earlier in the video but removing these
mirrors is a little bit fiddly because there's loads of little clips that go around the outside
so you can't just yank on it because you'd break all the clips so you have to go through one by
one and just unclip it with a screwdriver that's the easiest way I found to do it was just unclip
it with a screwdriver and then you can pull the whole mirror off then and it's really straightforward
from memory the small mirror at the bottom is similar to take off as the big one but I think
there was only like one or two clips or a spring clip that holds it in and once you've done that
there's five or six bolts to remove again sorry six or seven bolts I think it was to remove again
and then just all of the little clips that go around the outside to hold the cap on
something I didn't realize previously because the other mirror had detonated
but you have to remove the air temperature sensor and the puddle light before you can actually take
the mirror apart or at least that's how it seemed here as you saw me just do this is the bit I need
and I'm not sure if I said earlier on but this part is you can't buy this separately so you have
to buy the whole mirror which is over a thousand dollars so I'm glad I got this and it doesn't
look like anything's broken on it so that's really good I'll just go and clean this up in the sink
and try and get some of these paint marks off and then I'll be back I cleaned it up as best I can
but I don't know if you can see those few little dots on it I can't get those off I don't know what
they are but if anyone has any ideas of how to remove these I'd be greatly appreciated if not
I'm going to see again if I can find another one because I like everything being right so
let's get this fitted really easily then the chrome cap just literally clips in place like that
you can line the light up there's like some little like locating holes for the indicator
and you can kind of see roughly how the wiring goes it's really straightforward and then literally
the cap just goes on and you can put all the sensors back in and put all the bolts back in
it's really really straightforward so I thought that the mirror saga was over now and I put all
the mirror back together as you just saw apart from the glass and I was just trying to wipe off
some of the excess glue from where the previous owner had duct taped the mirror back together
but what I used to do that was brake cleaner now this is where my error is is that the brake
cleaner in the US I mean it smells different but in the UK brake cleaner would just take stuff like
that off and it wouldn't damage the plastic but here there's obviously something in it because
it completely ruined the mirror so this was the mirror that it ruined initially this was the
original cover for the front and it's kind of like made it go funny what happened then as well then
was that while I was cleaning that because it was all assembled and I didn't think about it
because I thought well brake cleaner is fine like I always use it in the UK for cleaning stuff like
that what ended up happening was it burnt the plastic of the back piece which is exactly the
piece that I needed the whole reason I bought this mirror was for this piece and you can't
buy this piece separately because Ford so I burnt it and so then it left some like I mean you can
still see them kind of in the middle of there maybe just about some burn marks so it ruined
that and now I thought well like I've tried for hours to try and make it right and I got it somewhat
right by sanding it but now you can see sanding marks so very irritated about the whole situation
considering now I've got three mirrors and none of them are quite right this I'll put it back
together with this cover on but it's not right and I'm gonna have to get another mirror so I'm
gonna end up with four mirrors to try and fix one mirror but like I said before I think the mirror
is a thousand dollars or over a thousand dollars for this specific mirror so I don't want to just
waste a thousand dollars buying a new one so I'm just gonna now gonna have to wait and see for
another one that comes up with the two holes at the bottom like this because it's very specific
because it's got like lights in the bottom so um like driving or flood lights or something for when
you're reversing or puddle lights sorry they're called but yeah I'm gonna put this on and um
not touch anymore today because I'm annoyed so I'll come back to something tomorrow
after this ordeal was over my next job is to fit my new led lights that I bought these are h13s
and they're made by beam tech um so uh yeah hopefully these fit in the thing it doesn't
look too bad to do um I looked already so to get this off to get down there you literally just take
this one clip out there and then I think it gives you full access to the back of the lights there
and then this one you can get to straight away down there so I'm just going to flop these over
I just got these out these h13s are really difficult to get out and what happens is the
seal here gets stuck on the headlight so I was struggling to get them back in
until I realized that the seal was stuck but you can probably see even over the light
you can see the light flashing there that's the main beam
you can't see the old one though well you can barely see the old one so I'm quite excited
to see what these are like one thing one thing I will do though is I'll be adjusting these if
they're too low down because obviously I don't want to blind anyone because I hate that myself
so I will adjust them down if they're not correct but
they look neat though compared to the old style ones or the halogen bulbs
next on the list is sorting this bump here now I bought this truck on the premise that it had
a dent in the quarter here or the rear corner I'm going to probably get that sorted next year when
it's a little bit warmer but there's a dent there and there's also a quite big dent over there so
I hate the look of that I thought or I found that you can get an even better bumper for this
a newer one will fit this so that's exactly what I've done I've got a new takeoff bumper
there's a couple of small marks on it like there where it's been rolling around in the back of the
trailer or truck but it's never had a license plate fitted to it so I'm going to fit that
to this and there's very minimal modifications that you have to do to make it work so
let's get on with it so taking this off I only had a really primitive tool set and I didn't have
any deep sockets long enough to actually get these nuts so I had to like really carefully
just extend the socket and not lock it in properly on the ratchet to get those undone
there's literally only a few bolts that hold this on I think six bolts hold this on in total
and then there's a couple of clips obviously for the tow socket electrics and then also
there's one clip for that that unplugs the whole wiring room for the reverse sensors and lights as
well it's actually quite difficult to get the clips undone though from where they are because
there wasn't a lot of like length in the cable to pull them apart so once I got those undone
it literally just was a case of lifting the bumper off and it was as simple as that
and luckily the tow hitch kind of held it in place as well so it was it wasn't like it just
dropped because it is pretty heavy and now the bumper's off all I had to do was carefully
unclip all of the wires and or all of the little clips and then feed it through these are really
difficult to get off but it was really straightforward once you once you do it
when I looked online about these it said that the sensors fit but they have to go in the old
in the new pickups things here like the caps but they definitely don't fit so
I'm not quite sure I'm going to do they fit in there like they slot in but they don't lock in
you might be able to see it's because they don't sit down far enough the outsides aren't so much
an issue because they are kind of level so I think they'd be fine but the ones here on the inside
the ones on the inside here you might not be able to see it they don't go down all the way
they're kind of like satin because they're resting on the this bit of the bumper here
I don't know you can see it they don't go down far enough so I have a feeling that's gonna
flag up an issue got my new bumper bolted up um it really does show the damage to the side now
that it's bolted up but when you look over this side you can see that it fits nicely on there so
um I can't do anything about the damage there until I take it in and get it sorted but other
than that it's looking good so we're a couple of weeks later now and I'm going to try and remove
the bumper from my truck and try and fix those sensors in there correctly I've got all my tools
now so I'm a lot happier that I can do this a bit easier hopefully so with great patience I
managed to make this is the second one so the first one I didn't do as well and the tabs broke
what I did is I first started with using my little die grinder here and I just literally went
sorry actually I first started with this one with heating it up with an air gun don't use a blow
torch like I tried to do because you can't control it as well but just heat it up so it just gets a
little bit warm and I took a pair of square pliers my nifex ones I used and I just pinched
about halfway down and then bent them in because originally the new sensors oh sorry the older
the new style sensors I think are rounded whereas these ones have got a flat there you can see
so you need to flatten these out take a die grinder and I just went directly up and then
I very carefully used a knife just went straight up straight up and just broke it off and it makes
a very nicely oh that one's not clipped in there we go very nicely clipped in sensor
that can't fall out you do need to heat these very carefully because they break between there
and if they do break between there all I did was heat the tip of a knife blade and just
gently sort of melt it across on each side and that's what I had to do on the other side that
one over there but on this one I got it perfect just by not being too ham fisted the next two
are going to be quite difficult though well they're going to be similar but then they're
going to be a bit more difficult so let me just fit this in now this is done
so before modifying you can see these tabs are like rounded which is too round to actually
pick up on the clips on the sensor so you need to square them out as I'm about to show
so you can see I squared these out a little bit it doesn't take much just to clip on those sensors
it doesn't it really doesn't need much to hold it so now they're squared out I'm going to just
die grind it and then just use this someone's going to moan at me for cutting near my finger
but you really do need to hold it I am a surgeon and all I'm doing is being very gentle just to
push it but I've got my hands both sides to sort of guide it because obviously I don't want to jam
it into my finger just wouldn't be very happy if we do that okay that's that perfect see it clips
in nicely what I would recommend actually is if you've got painted ones of these on the outside
like I have don't do those first because if you do mess this up the inside ones are not painted
generally and these are only like six dollars a piece something like that maybe even less than
that so if you messed one up it doesn't make any difference whereas if you'd mess the sensor up
it's like 50 or 40 or 50 for a genuine one so I'd rather do it like that so I've just got
one more to do with these and then I've got to modify the bumper very slightly so the last thing
to do to fit these was just I just had to die ground out this sensor hole here or near the
sensor hole so the sensor can pop in so the sensors in you can see the gap around it so I'll
just plug the plug back in now all done last thing to do is fit the bumper back on so just try and
get I was just trying to shake out all the swarf from the die grinder when I had to grind the bumper
part out for the sensor to fit because I imagine that I'd leave loads of little rust marks everywhere
I'm back over at my friend Frank's place today and the last I think thing to do to this I'm just
going to quickly service it now um I haven't serviced it since I had it and I think about
I can't remember it was probably about 10 000 miles ago roughly maybe slightly more
but it was last serviced and it's not expensive for oil and filters and whatnot
I also got a few other bits for this so um I am going to quickly just dump the oil because it's
warm right now and then we'll get on with everything else I think as well I'm going to
try and do in this video the spark plugs and annoyingly there's 16 spark plugs in this because
it's a v8 but it's twin plugs per per head so uh there's one there and then the other one is there
for each one so it's going to be pretty time consuming I think to do maybe not those ones but
these ones might be a bit more time consuming but we'll see how we get on and maybe once I
get the filter out it might make sense to quickly do those so I'm trying my best not to get scolded
by the exhaust because it's really hot right now and it's very near my face
but oh god this is it
I've got it in my face
okay
right put that back on and I'll write the date and mileage on that in a second
so the air filter I'll take off next now something I like about these Fords is that I feel like
the European Fords from what I've seen everything's just a bit of a pain and they're a bit problematic
whereas like everything just seems to be in nice places here so far I haven't found the cabin filter
yet but like this is just there it's really easy to get to although I'm going to take this off so I
can do the spark plugs as well while I'm at it so I will say one annoying thing about this is it's so
big that even for me being uh what am I two point I think it was 2.13 yards tall um I am struggling
to reach everything so it is a bit of a pain like that for me but otherwise it's pretty good to work
on and just like that everything's really easy to get to like the alternator seems really accessible
the starter's accessible just seemed like quite a good truck to buy and it does have its flaws
because it is really juicy but at least like if I want to work on it I can whereas the diesels
I think you have to take the whole cab off to fix anything on them so these small clips on the top of
the spark plug thing the coil seemed quite nice so I think you pull them back and then push it down
it just comes out like that same with all of them we'll just go through and remove those now
so now those are off it looks like a case of taking these off all the way down I'm going to
do the last two on either side or the last one on either side later but these look really
straightforward to just pull out of there that's really nice so I'm not sure if you can see but
the end of this spark plug cap is slightly corroded now I wonder if there was a little bit
of water that got down the side because that one didn't seem to be sealed very well so I'm hoping
that coil's not bad but it did also seem to run a little bit lumpy on idle so it might be something
to do with that but I don't know we'll replace them all and see how it goes from there and
worst ways I can keep an eye knowing that that coil wasn't sealed very well I have done all of
these spark plugs and I hope whoever left the rubber which I'll show in the picture on the end
of that spark plug stops their toe every day for the rest of their life because I suffered
for about an hour trying to get it off because it like welded itself to the spark plug
but yeah all of the 16 plugs are done put the new filter in and Frank and I are going to now
try and top the hole up with the world's smallest little hole there should I move my new air filter
out the way do you think I'm gonna miss yes why don't you turn it upside oh that's a good idea
that's why and oil pressure so my truck's all done now all serviced it's running great it doesn't
seem to be running lumpy either now that I've changed with those spark plugs and part of it
may have been whoever did this which I think I said about in the video but whoever left this
cap on because it was so difficult to get off but I think that might have been why it was not
running correctly but like I say it seems all right now so fingers crossed it stays that way
and yeah I'm really happy with it and I'm glad I bought it so if you liked the video
don't forget to like and subscribe and see you in the next one thanks for watching
