5 MOST COMMON Latte Art MISTAKES and fixing them

About Coffee in life
92 followers
AI Generated·May contain errors
I am a firm believer that anyone can pour latte art. Yes, anyone including yourself. But today I
wanted to show you five things that you're very likely doing in your latte art that's holding you
just that one step back. And if you do all of these in conjunction with one another, I'm very
confident that you will see an improvement in your latte art. Number one, integrating too much.
Integration or pre-mixing is just that little bit of milk that we add at the beginning prior to
pouring the design. This helps establish a new consistency in the milk and allows the pitcher
to get closer to the coffee sooner. If you integrate less, your pour will have more space
and more time to fill the cup and you could end up with a larger and fuller design. If you integrate
much more before the pour, nice rhyme, you'll see a smaller design due to less room in the cup from
the amount of milk you've added. And having more milk in the cup prior to the design will make the
flow of milk a bit more stiff because there's more foam present. Integration and how heavy you pour
with the pitcher will directly determine the size of the design in the end. I usually integrate just
about an ounce in my little six ounce cup, though that would be dependent on the cup size you are
using. The next mistake you're for sure making is not preserving the crema. An easy way to fix this
is to stack your cups. Stacking your cups keeps more of that crema on top by lessening how much
breaks up from the height of the spouts. Having more crema is by no means a necessity, but it does
add a deeper contrast to the pours and it'll make your latte art pop. Let's take these pours for
example. Both of these are great pours, but the one with the crema just kind of hits a bit harder. It
also tends to glide a little bit better when there is a nice fresh crema on top, though that is not
always true for all coffees. In the case of dark roasts or robusta, you might actually see a crema
that is too thick and inhibits your ability to pour. In that case, I would end up pulling the
shot in one vessel and then transferring it into the cup I'm going to pour into. This will help break up
some of that crema and basically do the opposite of what we would do otherwise. Next up, not swirling
the milk enough. Foam is full of air and less dense than milk, so when you're finished steaming your
milk, it's constantly fighting against you to rise up in that pitcher. We can refer to this as
separation, and to prevent that separation, we're going to swirl our milk, but you're probably not
swirling enough. If you don't swirl enough, instead of getting that clear defined image, you'll just
end up with a big foam turd on your cup. Look familiar? So just before you're about to pour,
that's another good rhyme, I want you to swirl the milk in the pitcher vigorously against the sides
until it becomes thin and there's no dome of foam, another good rhyme, on top of the milk. Next mistake,
you're rippling too fast. Rippling is the swinging of milk in the pitcher side to side, and if you're
holding the pitcher too loose or you move your hands side to side with the pitcher, that wave
will not form, and it's common for folks to try to ripple quickly and sporadically. This unfortunately
doesn't produce the best latte art, so to correct this, instead of violently wiggling the pitcher,
aim to make the waves wider. If you're gripping firm and the wave is wider, then the swinging will
become more consistent. This is similar to when you're pushing someone on a swing. If you push
someone with more force, they swing up for longer and more consistently as the wave or swing
dies down. If you push someone rapidly, well, they would die.
Not tilting enough. This is by far the biggest thing that people make a mistake on. Not tilting
the cup enough is going to limit how close the spout can get to the surface, giving your design
a beige beginning and very little control over the flow of milk. However, if you were to tilt the cup
to the point where the liquid is almost spilling out, you will notice an immediate improvement on
the contrast and consistency in the color of your pours. The other culprit is having too much liquid
in the pitcher when we pour. It's important to have the liquid line coming from the spout to
be as close to level with the cup as possible. Anything higher will prematurely spill out when
you attempt to get close to the surface. You will again see beige, and also this is wasteful, so
don't have all that extra milk in there to begin with. This is another reason why I'm a big proponent
on steaming milk in a small pitcher and transferring it to a larger pitcher. If you have a smaller
amount of milk in a larger pitcher, when it's standing right up, it ends up being a shorter
amount in the vessel, and when it's tilted to the side, it elongates that milk, making that liquid
level closer to what you have in the cup. And this is going to give you a lot more control when you're
trying to flow in Latte Art. If you want to hear more about my theory on using a bigger pitcher with
a smaller amount of milk, make sure to click this video right here. It's actually the first video I
ever made on YouTube, and it's all ready for you. I really like it, and it goes over the entire
philosophy. But I'll see you guys next time. Cheers, you dirty scumbags.
