Sewing My Redthreaded 1860s Gored CorsetSewing My Redthreaded 1860s Gored Corset

Pre-modern Women's Fashion
182 followers
28 Video Views·May 13, 2026
This sewing video is about making my Redthreaded 1860s Gored Corset.
This video contains the following steps in the sewing process:
00:00 Introduction
00:35 Pattern Pieces
1:01 Fused Pieces
03:49 Quilted Pieces
06:42 Bias Binding
07:45 Inserting the busk
11:39 Bust Gores
13:27 First Bone Channels
15:12 Joining the Front to the Side
15:30 Hip Gores
16:38 Back Panel and Top-Stitched Bone Channels
17:34 Inserting the Bones
17:59 Grommets and Lacing
19:09 First Fitting
20:15 Side Bone Channels
21:51 Binding the Lower Edge
22:34 Another Fitting
22:50 Bust Gore Adjustment
23:26 Binding the Top Edge
24:00 Lace Decoration
24:40 Flossing
26:08 Arrow Hook
26:27 Finished Garment
AI Generated·May contain errors
Hello, I'm Catherine from Crystal Pegasus Costumes,
and welcome to this video, which is all about how I made
this corset. I used Red Threaded's 1860s gourd corset pattern, and I have a
separate video about my mock-up process, where I
adapted the pattern to fit me. And so, without further ado, let's
Here are all the pattern pieces, as I got to in the fitting video.
When I take away the gore pieces, the ones left
will be silk fused to coutil. The gore pieces will all be quilted, which
we'll look at soon. First, let's prepare the fused pieces.
Three layers were used. Firstly, a white small weave herringbone
coutil, a red silk satin, which I was fortunate
enough to buy most of a bolt as a remnant,
and bondaweb, a double-sided iron-on fusible interfacing, to join the
two fabrics together. I laid out the silk, wrong side up,
then the bondaweb. I trimmed down the silk,
leaving overhang at all edges, and pinned the layers together.
I used the iron to fuse the two layers together,
working outwards from the centre, and doing a small part
at a time. It was a slow process, but the outcome is worth it.
I peeled off the bondaweb backing paper, then I laid out the coutil,
laid over the silk, right side up this time,
so the fusible layer is towards the coutil.
Then I smoothed and pinned as before. Back to the ironing board, where I fused
the silk to the coutil. Then I was ready to cut out my pieces.
I laid out the pattern pieces, aligning the grain
and pinning at both ends of the grainline,
then weighing down. I cut out the pieces with my
rotary cutter, using a ruler for the straight edges,
and free-handing the curved edges. I repeated the process for the rest of
the pieces. I transferred the gore and bone channel
markings onto the inside of the pieces,
and the fused pieces were prepared. For the hip and bust gores, I created
a quilted textile, using coutil, two layers of bamboo cotton batting,
cotton sateen, and silk. I smoothed and weighed down the layers,
then pinned around the edges. Firstly, I stitched along the top edge,
using a walking foot, to secure the layers together.
I laid my ruler at the desired angle for my quilting,
and I tacked on a guideline for me to follow
for my stitching. I kept the fabric as flat as I could, and stitched along
next to the guideline. Then I stitched another line,
two centimetres over and parallel to the first,
and repeated for each line. Once I had done
from the middle to the right, I did the same
the other way, and moved from the middle, two centimetres to the left each time.
There was a decided difference between the two halves,
so I decided to work from one corner over
for the second direction of stitching, as much as I could,
and tacked down my next guideline. Then I stitched the second direction of
the quilting, and my quilted textile was complete.
Walking foot for the win! I pinned down my pieces, aligned the grain,
and traced around them. I stitched just inside the lines I had drawn.
We can see it from the front, and from the back.
Then I cut out the quilted pieces along the drawn lines.
To be able to bind the edges, I cut by strips of silk. My next step
was to bind the edges of the gauze and facing pieces,
which will be visible on the inside of the finished corset.
For the gauze, I sewed the binding to the wrong side,
as that's where the edge will be visible. The silk had a tendency to fray,
so I decided to overlock the quilted edges
that were not bound, or not going to be sewn.
I ironed the back lacing panels in half, and stitched along the bust gore line
on the front panels. And with that, all the pieces were prepared, and I was
ready to start assembly. It was time to insert the busk, and I
started pins side first. I stitched the facing to the front
piece, along the center front line, as marked on the facing piece.
I pressed the seam allowance towards the facing piece,
and then topstitched. I pressed the front piece,
so that the center front lines matched up, and the placket was created.
Then I stitched in the ditch, along the center front line.
Time to bring in the busk. Taking the pins side,
I marked the top and bottom of the busk, and the location of each pin.
I used an awl to create the holes, which I inserted the pins through.
Pausing on the pins, it was time to start the loop side.
I pinned the front to the facing, aligning the center front line.
I marked the top and bottom of the busk, and then the location of each loop.
I stitched along the center front line, raising the needle, and skipping over the
areas where the loops need to pass out.
I pressed the seam open, then topstitched along the facing side,
and pressed the seam closed. I inserted the loops,
and tested that it could attach smoothly to the pins,
which it could. I used a bone to pull the loops through, while I stitched
the busk in. Using a zipper foot, I stitched right
next to the busk, on both the front pieces.
Hurrah! The busk was inserted. It was time to insert the bust gores.
First, I cut down the center of the gore opening,
then I warmed it up with the iron, and pressed it open
along the sewn fold lines with my fingers.
I pinned the bust gore into place, starting at the very bottom
to set that position first, then pinning up
each side, easing it around, and ensuring that the edge sits 10
millimeters from the edge of the gore. Next, I
pinned the second side. I topstitched the gore
into place, I trimmed down the folded-in coutil,
then I stitched a second line around the gore,
securing the raw edges underneath. I repeated this process
for the second gore, and the other half of the corset.
It was time to add those bone channels, which
do not go over the hip gore, starting with the side back pieces.
I stuck pins through to mark the line of the bone channel
onto the right side of the fabric, then on the wrong side,
I laid a 20 millimeter wide herringbone tape
along the line, and used masking tape to hold it in position.
I stitched down the center of the bone channel
along the pinned line, as this was a double boning channel.
I removed the masking tape, then I stitched
eight millimeters either side of the center line,
and the double bone channel was sewn. Then the bone channels on the front
pieces were done in the same way. The line was
pinned through to the front, and the herringbone tape
was held in place with masking tape. I stitched down the middle of the
double bone channel, then removed the masking tape. I
switched to the zipper foot, folded the bus gore out of the way, and
stitched eight millimeters from the middle on either side.
Then the same process was repeated for the other bone channels
on the front pieces, which were all the bone channels I needed to sew
at that point. I pinned the front to the side,
then stitched, pressed the seam towards the front,
and topstitched to secure. I trimmed down the top layer of the seam
allowance, and I was ready to attach the hip gores.
I pinned the hip gore to the main piece of the corset,
starting at the balance marks and moving my way
out. I stitched the two pieces together, then stitched on a piece of bias binding,
because I wanted to minimize the bulk of the quilting,
and finish the edge. I trimmed down the seam allowance of the quilted hip gore,
and clipped the fused coutil layer. I folded over the bias binding, and pinned
that down. I topstitched with a white upper thread,
red lower thread. Then I did a second line of stitching,
and even a third, to really hold that seam allowance down.
It's not perfect, but I was happy to try new things.
Time to finish the assembly. I stitched a bone channel
parallel to the busk, topstitching through the two layers.
I topstitched along the center back edge of the back panel,
then I pinned the back to the rest of the corset,
and stitched with a 15 millimeter seam allowance.
I pressed the seam towards the back, and topstitched,
then trimmed down the seam allowance. Next came the bone and grommet channels
at the back. I stitched in the ditch along the seam on the back panel,
and then 12 millimeters in, creating another bone channel.
At this point, all the pieces were assembled, which is an exciting part of
any project. It was time to insert the flat steel
bones either side of the grommets, and next to
the busk. Then the synthetic whale bones into the
I had shaped the ends to match the bone channels where needed.
Grommets next. I marked the grommet locations,
and cut holes with my prim pliers. I inserted the grommets in my normal
manner, using the prim pliers, two part grommets,
widening the hole with an awl, pushing the first part through,
second part goes on next, and then give it a big squeeze
with the prim pliers. And a grommet is done.
Here we can see the back, and the front, and then I added in the laces.
Almost ready for my first fitting of the corset.
The final step in preparation was to tape in the remaining bones,
leaving them free over the hips. So here we are,
the first try on. The purpose of this is to pinpoint the location for the bone
channels over the hip gauze. That's why it's all
quite lumpy lumpy down there. As you just saw,
these are taped on, and so we need to work out where they're going. I think I'm
pretty happy with the bottom of the corset,
and using the line that was planned, we'll get these bone channels in,
trim it up and bind the bottom. I'm less thrilled with the top, but my
thought is let's get the bottom sorted first,
and then we'll turn our attention up here. I gave the bones a wiggle
to check they were sitting where they wanted to, then marked the locations with
pins. I compared the two sides and evened up
the placements, then marked the location of the bone
channels over the hip gauze, and transferred the
bone channel lines to the outside with pins, in the same way I had
earlier. I laid on the herringbone tape, and as
these were single bone channels, not double, I could only tape one side,
and used a few pins to hold the other. I stitched the first side of the bone
channel, keeping the edge of the foot following
the pinned center line. I removed the bones and masking tape,
then I stitched the second side of the bone channel.
To finish these single bone channels, I stitched again
either side, creating double lines of stitching.
As well as the look, this had the benefit of catching down the tape.
Did the same for the rest of the side bone channels,
then inserted the bones. After a quick try-on to confirm I was happy with the
progress, I was ready to bind the bottom edge.
I trimmed down the bottom edge, I attached a strip of bias, right sides
together, and stitching with red thread. I
pressed the bias binding down, then I folded it
over, and pinned it in place. I stitched in
the ditch, and after a press, I had a nice neat
binding on the bottom edge. It was time for the
next fitting. I was very happy with the lower half of
the corset, and the bottom edge, and how most of the
top was sitting, but I decided that the apex of the
bust needed to come in just a little. I carefully
unpicked the top six centimetres of each gore
at the bust apex, and tied that off underneath,
burying the threads. I moved the edges of the gores
in, so that they were touching, and pinned into position.
I re-stitched the gores down, and then tied off and buried the threads. The
stitching was a bit wobbly, but at least it was done. As I did when
binding the bottom edge, I trimmed the top edge down,
stitched on a strip of bias binding, which I folded and pinned down,
and then stitched in the ditch. At this point,
my corset was fully structurally assembled.
After considering a few options of decorative lace,
I decided on a white cotton lace with ribbon trim, and after a few trials,
I settled on a yellow silk ribbon. I pinned on my lace, then stitched it
down along the top, and middle,
and bottom. The next decorative element was the flossing.
I tried a few options on a flossing sampler,
and determined that I wanted to use Devere Yarns
size 36 silk, number one white, 101 blanc, 68 banana,
and 90 ingot, coming together to form a little gradient. Then onto the
corset. For greater detail on flossing technique,
please see my flossing videos. I created a gradient from light to dark,
carefully counting stitches and spacing it out.
All the ends of the threads were buried, keeping the back
nice and neat. I was very happy with how the flossing came out,
and thought it added a certain something special.
I also decorated the base of the bust gauze,
which had the benefit of securing them nicely.
The final piece of functional decoration was the arrow hook for holding down
petticoats. With it in place, the corset was
complete. So here we are, my completed 1860s
broad corset. Overall, I'm absolutely thrilled with it.
I think it came up really well. I'm pretty happy with the fit,
although it's not completely perfect along the top line, there's a bit of
space there. But for the moment, I think that's
nothing that a ruffly corset cover can't hide. I am particularly pleased
with the quilting, and the flossing, and the lace.
I think those are details that really make this corset.
Plus the va-va-voom shape, of course. I do feel really comfortable and
supported. The waist is sitting nicely, and then
there's the support from the corset under the bust, and the chemise at the
top. So overall, I am very happy and excited
to get on with more 1860s garments. Thank you very much for watching. I hope
you'll join me again next time. Goodbye.
