http://www.VideoJoeKnows.com Drywall patches: applying a 2nd coat of quickset?....is it really necessary? "Joe" always applies 2 coats of quickset to his drywall patches.....they just come out better when you apply a 2nd coat, plain & simple. If the first coat of quickset, over your drywall patch, is not even, lumpy, or a nice full coat, &/or smooth, you're looking for trouble if you don't apply a 2nd coat. Especially over drywall patches, "joe" uses a self adhesive webbing tape before applying the quickset. If "joe" only applies one coat of quickset, then the webbing tape usually does not get nicely coated as well as "joe" would like, without applying a 2nd coat. For that reason alone, "joe's" patches come out looking good.....time after time after time. Let's watch as "joe" applies a 2nd coat of quickset over his drywall ceiling patch. The more you watch....the more you learn! http://www.VideoJoeKnows.com
AI Generated·May contain errors
Now your next question might be do you have to put two coats of Kwikset on here?
Could you put the all-purpose general all-purpose joint compound on next after this dries? Yeah you
could do that but I'd like to put a second coat over this of Kwikset because then it fills up
the voids and you can't really see them from there but I see one here one here uh maybe a little bit
in there right there over in here a little bit so I like to get a little bit more mud up there
the second coat's not I'm it's not going to be very much but I want to get it in there
because if I put the all-purpose joint compound in there now after this dries it might have a
tendency to shrink a little bit more and I might have to put a couple coats on there because what
I want to do after I get the next coat of Kwikset on here I'm going to let that dry
today too and then I'll be able to uh scrape that a little bit and put the first coat of all-purpose
joint compound over that and I don't want it the all-purpose joint compound I don't want to put
too many thick coats of that on there because it's going to shrink I want all the back surface
the first and second build up coats of Kwikset then I don't have to put as much
all-purpose joint compound over that okay that's just how I do patches my patches come out looking
good too so will yours I've got a four inch broad knife and it barely covers so if you're good
you can just use your four inch wiping off any excess as you go now the more patches you do the
better you're going to get with them now if you want to use a six inch I got a six inch here
might be a little bit easier to use now because it'll cover all the way I'm going to try to keep
most of it off of the rest of the surrounding patch and it's okay if I get over here as long
as I wipe it off because then I'm going to sand that when it all dries okay so I can use a six
inch here too for that easier to put it on because it covers the entire patch area where I need I
don't have to be as careful you know like I said because we had the groove I'm just going from
groove to groove filling that in I'm not tapering it over to the existing of both sides like I would
normally on a patch because I didn't have that type of condition here trying to backhand it up here
wipe off my edges and I'm seeing some little lines in here and I might have mixed it up
and got just a little bit of dry spit in there I'm getting it up off I could have mixed it a
little bit more as I was getting it mixed up in the pan I want to wipe off any excesses that I
I was going for my face
drop the excess around the patch there it is could maybe put a little bit more right in there
got a line in there I'm going to try to use some different mud out of my pan
just keep going until I get it off of there okay that's better I think I'm going to leave
leave it at that for now let that that dry that's all I have to do with my quick set
now see if this was a different patch let's say I had tape up there and I didn't have a nice
groove to fit it in I would have had to have bridged it over a little bit further the patch
because if that if you can imagine a piece of tape just on a on sheetrock let's say there
are two seams butted straight up together some butt seams or something you had to put a
piece of tape over there well now you're building up the uh the overall surface so each time you
put more mud on you have to bridge that over so that eventually a patch becomes this wide
well because we already pulled that tape off all I had to do was fill up that inside bit you know
what I mean once this dries then I'll be able to put the all-purpose joint compound on there
and then I'm going to make it I'm going to bridge it out a little bit further because what you want
to do is is that all purpose even if I could get even if I got this perfect and I thought okay I
don't have to do anything because it's quick set the primer and the paint's not going to
adhere properly and it's not going to blend well it's going to adhere but it's not going to blend
in to the rest of the ceiling you're going to see exactly where this patch is because no matter how
smooth you get quick set it's a porous material and the paint takes differently than it does
with the all-purpose joint compound which means this joint would stick out like a sore thumb
and look like who did that patch and you say man I got it perfect what's happening how come it
didn't blend in well it didn't blend in because you didn't put a coat of all-purpose joint compound
over this when I put that over this I've got to bridge it out this way a little bit
because it needs to be thick enough to cover this okay you'll see