Sanding a drywall quickset patch

VideoJoeKnows
63 followers
2 Video Views·May 9, 2026
http://www.VideoJoeKnows.com Sanding a drywall quickset patch is a good idea, before applying the finish coats of all purpose joint compound. Is it really necessary to sand the quickset drywall patch?....After watching "joe", I'll let you be the judge of that. Quickset is the perfect material to use, for a drywall patch. Just make sure you don't just use quickset, then directly paint over your drywall patch.....that's a no no. Let's watch, as "joe" shows & explains a little bit on why he sands a drywall quickset patch. When you get done with sanding the drywall quickset patch....is it time to apply the finish mud? Ah.....one more quick task to do first....or you'll be sorry!
http://www.VideoJoeKnows.com
AI Generated·May contain errors
After that second coat of Kwikset, you'll notice it's already drying really nice.
I'm just going to go around the edge again and lightly scrape anything I see. That's another
reason why I like to drop my construction light because I can have it at an angle like that. If I
didn't have that in here and I was just using the kitchen light, man, I'd be a little concerned
because there'd be lots of things that I wouldn't have seen, you know, and I think this is almost
ready to sand too. I'm just lightly testing it out to see if I'm ready to sand. I think I am.
Let it go just a little bit longer. I think it's okay right now, but here's what I've learned.
Sometimes when I think it's okay and it's about this shape and I get ready to sand it, if this
Kwikset is not dry enough, you're going to start dragging that material. Then you're going to be
like, oh shoot, now what do I do? Do I put some more Kwikset on there and get the Kwikset back
out, mix that up, put some more on or do I leave the long gashes I just made with the sander
sanding pad and then do I put the all-purpose joint compound and I hope it doesn't shrink too
much and all that, you know. So if you're questioning it at all, you can do a little
light sanding, but I just let it sit for a little bit longer then before I get my sander up here.
I got a little sanding paddle. I'll show you that in a minute.
Let it dry a few more minutes. I'll be right back to you. Now here's something I want to point out.
Why am I going to sand this? Now technically I don't have to sand the middle. This is Kwikset
and I'm going to go over that again. As long as the Kwikset is smooth, you don't need to sand over
that to put on your all-purpose joint compound. The only places I do want to sand and it's dry
enough is any overs that I got beyond my patch area. So because this was indentated, you know,
where I pulled the tape out, I can sand from there over and there's a little bit of dusting
of Kwikset from here over to there, from here over to there and that portion's dry. You can't
even see that because it's so thin. That's why that little section's dry. It's deeper in here.
That's why this is still discolored. Even though this is hard, it's still drying. Okay, so I'm going
to go around this and I'm going to lightly sand. I'm going to sand the outside edge. I'm going to
sand that so that when I put my all-purpose joint compound, I don't have to put as much beyond this
point over. If I left this other Kwikset up here and the ridges to the Kwikset, then I'd have
to bridge over the ridge over this far. So if I sand that little bit nice and smooth, then when I
put my all-purpose joint compound on here, I don't have to bridge it over as far. Okay, that's why I'm
going to sand this right now. So I'm trying to keep my patch to a minimum up here. Now if this
was on a wall or if I was doing more, you know, I could leave it exactly like this and I could
bridge way out here from here to here with my all-purpose, you know. But because I have that
nice little groove in there, I'm going to sand a little bit of that and be ready for my all-purpose
joint compound. Like I said at the beginning of this video, not all patches I do the same.
It just depends what the existing conditions are as to what I'm going to do with the patch. So it's to
your best interest to watch all the different videos I do because I'm doing them for a reason
that maybe you'll pick up something that you're watching me here above and beyond what you watched
when I did another sheet rock patch on a wall or on a ceiling or something else. Okay, that's what
it's all about, continuing to learn. Okay, so here's my paddle sander, just a sanding pad on a little
plastic holder. I folded those up, tighten that down. I even push the sides up in case I want to go
in an inside corner or something. In this case, I don't and this was only like $10. Okay, so now I'm
going to sand that just slightly around the edges just so when I get ready for my all-purpose it's
going to blend in there nice and smooth to the existing. Okay, so I don't even have to hit the
middle. I'm just going around the edges because I have my light on. I'm tapering it as I go.
I probably should get on my ladder and reach over so it's not in my face or anything.
When you're doing this on your own, you probably should have some eye goggles on or maybe even a
dust mask. I don't have either one. I want you to hear what I'm saying and this dust is all in the
air now. That's why you've got to have your windows closed, fans off. Most of it wants to go straight
down if the air is not moving around, but if the air was moving, this would fill this entire room
and you have it everywhere. I can see exactly where to sand this because of the light.
Tapering it in. You don't have to do it really super hard. I can see where I need to sand a
little bit more than other areas. Just move my ladder along. Now, there's nothing tricky
about these patches. If I can do it, you can do it. No doubt about it.
Just a little know-how, a few tools, a little Joe in your brain. You'll be able to do it.
You'll be able to do it. I know it and you'll just get better with each patch you do. That's
ready. There's one more important thing I need to do before I put the all-purpose joint compound
up there. Do you have any guesses what that is? It's going to make that all-purpose joint compound
stick better. What is it? If you said you've got to sweep that down or wipe it down, you're right.
I want to get the dust off of here. I don't have to do it too much. I just want
where I sanded. I want that to be nice and clean. When I put the all-purpose joint compound up there,
it's not landing on a layer of dust because then it might not bond properly. You might not even
know it until after you get the paint up there. Because the coat of all-purpose joint compound
wasn't up there nice, it flaked off or cracked. Caroline cracks in it or whatever.
That's all you got to do with that. Now we're ready with the all-purpose joint compound.
