Making a lapped seam corset, late Victorian, early Edwardian

Pre-modern Women's Fashion
182 followers
8 Video Views·May 4, 2026
This is a video I made several months ago when I was learning how to use Premiere pro. It is clunky and awkward, no captions, I mumble a lot - and since it was a learning piece and I didn't like it, I didn't plan to post it.
But then I realised that the techniques presented can still be useful for people wanting to have a go at a lapped seam corsetry and they might not mind the presentation much, but enjoy the details of construction.
So there you do!
A learning piece But i hope it will be useful to some budding corset makers!
Hello, Isabella from Friar Attire here. Today we are looking at this faucet. It's very late
Victorian, beginning of Edwardian one. It's one of our standard sizes and I'll be taking
you through the steps how to make one. Enjoy! Your fabric. Here's a rose splash couture,
very thin, very thick as well, very light. So it can be any kind of couture, a brush will do,
including cambric. That's it. You will need a busk, you will need boning,
both flat and spiral or you can use just flat, up to you really what you want to go for.
You will need eyelets. I'll get an eyelet press, I don't need an eyelet
insert tool but you can get these as well. You will need any cutting implements which can be a
rotary cutter, can be scissors. You will need an awl for making holes. You will need some
lacing for the back, obviously a bit less than that. You will need some bias binding or you can
make bias binding out of the self fabric as well, a very pure solution. Apart from that you will
need some tape for the channels. I've got some nice vintage tape here but any cotton tape will
do as long as it's strong and not stretchy. Lace if you plan to decorate it. Any kind of tools to
draw on your fabric really. A variety of different tools are available nowadays.
I usually go for a simple pencil to be honest. As you can see the seam allowances are quite
generous. I will mark them now on the other side but you will need that for your flat felt seams.
The outside does not really need a lot of precision, it all will be folded out as long
as you have enough fabric there it should be fine. Right let's continue cutting.
The busk is inserted as usual really. You've got your part one and the facing to enclose the busk
in. That's the left side, you align the seam allowances, align it and just mark where the slots
need to be. Dip it out and we have to stitch it the same way on the other side but because this
has just slats you actually don't need to worry too much about anything else. Just make sure
you pin it together and just stitch alongside that edge. Let's go and do it. For the busk you
will need a zip and a machine or a straight stitch and a zipper foot actually. And we need more.
Time to have a look at the backs. I like two of these. I just fold it over. The first thing
I'll just run a very simple stitch just next to the edge. It will prevent the bones from
twisting in their channels. There you go. Now unless I'm going to go over there and
although the fabric is quite sturdy I usually like to reinforce it with another strip of fabric
sandwiched in between. It keeps the eyelets a little bit more to grab onto.
Right let's go to the first channel and the second. There we go. Back channels are stitched.
Obviously if you're new to corsetry do mark your channels first. Make sure they correspond to the
width of your bones. After having made several ones you will just know it by heart. Right do
the other one the same way. I'm ready to start assembly. The knapped seam method is very different
from the usual assembly. We have the busk and we have the bust gusset. You can see the seam allowances.
I'm just going to stitch them together. I'm just aligning the gusset with the piece
making sure the curve is maintained. Now you can stitch this way all through the corset first and
then flatten the seams and lap the seams. I prefer to do it one by one mostly because I've got a bit
more control over that. So the next step is enclosing that seam. Trim this one and this
one has to go over, fold and stitch. But for that we need to press it first. So the seam is pressed
and I simply stitch it first very near the first seam.
Outside and you repeat through all the other pieces.
You can pin those two pieces together or you can use
the clips. I simply find that it's much easier for me to maneuver them on the curve by hand.
If you are in a hurry you can just fold and stitch without pressing.
Now the assembly is done we move on to putting some boning channels in. The waist state is put
first. This is just a nice cotton herringbone tape and after much deliberation between these two
I've decided to save the orange for a more contrasting corset and go with the white
cotton herringbone tape for the channels. Now traditionally in earlier models the channels
are usually placed over the seams. Obviously with those swooping seams you cannot really put channels
over there and because the straight front started to be fashionable at that time the channels go
straight all over the seams.
The amount of channels you want to place on it really depends on you and on your needs.
If you need lots of support put more, if you need a little bit less don't worry too much.
This is our standard 12 corset so some like that just like this.
Right so we have five channels each will contain two bones. You can actually start getting,
you can put one bone over here as well which I think I'm going to do it for.
I'm going to put this one first here. All I do I just pin the channels. Now the shape
is created by the cut of the corset not by the boning. The boning just supports the shape so in
this particular case it really does not matter much whether that tape is an inch here or an
inch there it just supports the shape provided by the cut of the corset. I'm not looking forward
to flossing it will be really hard I guess. Obviously the back already has its channels
so yeah so that's our boning ready for the stitching but just to just to show you
this is unboned corset that's what the shapes are. You don't need boning to create a shape you just
need boning to support it. Right let's stitch all the channels on.
So what we have here is a stitch channel of spacing for two bones
and let's do the same for the rest of them. Binding the lower edge. So we've got our corset
ready for boning really. Binding is on on the lower edge. Let us put the bones in. I've already
put the bones the correct length. You can either bone the corset completely with flat bones with
flat steel like these. Plastic so they're still quite nice over the hip. You can pre-bend it if
necessary. I do actually prefer to use spiral steels at the side and back just sake of comfort
and so let's get going. You can use artificial or synthetic wire bone for that as well.
It will work pretty pretty well too. You will need to file them individually but also as the century
20th century progressed you see more and more useful steel boned corsetry so that's it and last
There we go. All boned. Definitely heavy now. Right I just need to add
binding at the top and do the same one on the other side.
When you find out that your standard size 12 corset is a bit too big for you and you have
to make do with other things. Hands and hips. Literally. Just cheating.
