A few years ago, I bought the ugliest home in my neighborhood. The Curb Appeal, in particular, was horrible - so I decided to do something about it. In this video, I am going to show you how I transformed the curb appeal of this fixer-upper with various DIY projects.
Please note that I have detailed videos for all of the projects included in this DIY Curb Appeal Transformation video and I will link them down below.
This curb appeal transformation started off with a handful of cosmetic upgrades. First, I power washed the entire home and I replaced all of the broken pieces of siding. Next, I removed the old abandoned metal chimney and painted the entire house using a paint sprayer. Once the house was painted, I replaced the shutters and switched out the old front door with a new one. These cosmetic projects definitely improved the look of the home, but there was still a ton of work needed.
Next, I decided to completely revamp the front entryway. I started by removing the old metal railing and then I resurfaced the concrete steps using a concrete resurfacing product. After that, I demolished the old entry sidewalk and I poured a new concrete landing and curved sidewalk that connected the driveway to the steps leading up to the house. I then replaced the old railing with a new wire railing system.
Once the front entryway projects were completed, I turned my attention to the garden and landscaping. I decided to build a concrete landscaping edging to help separate my lawn from my garden. I build the forms using 2"x6" lumber and poured all of the concrete by hand. Next, I installed weed barrier fabric, planted a few evergreen shrubs, and filled the new garden area with black mulch. Once the concrete garden curb was complete, I applied topsoil to the lawn and planted new grass seed. Unfortunately, however, the grass did not grow in nearly as well as I would have liked. And for the final project in my Curb Appeal Transformation, I decided to build a gable porch overhang over the front door. Although this architectural improvement was pretty involved for a DIY project, I think it had (by far) the most dramatic effect on the overall transformation of my home.
Please let me know what you think of the DIY Curb Appeal Transformation! I would love to get your feedback on your favorite project, your least favorite project, etc.
My name's Andrew and a few years ago I bought the ugliest house in my neighborhood both
inside and out. In this video I'm going to show you how by pouring a ton of sweat equity into
these four categories of projects I was able to completely transform the curb appeal of this house.
Let's get this party started with the cosmetic upgrades. To kick off this curb appeal transformation
I started by power washing the entire house from top to bottom and as I was washing this asbestos
siding I noticed a few of the tiles were cracked so I removed those and I replaced them with some
fiber cement siding that you can buy from Home Depot and some people will say you really shouldn't
work with asbestos due to like health reasons and breathing in the fibers but I'm really doing just
fine. Just wear a respirator. And the house also had this abandoned metal chimney attached to the
side of it so I removed that and after cutting out the attachment where it actually connected
to the house I was left with this 18 inch crater in my foundation which I filled in with some rapid
setting concrete. In hindsight I probably should have used some reinforcement but fingers crossed
it holds up. Then I just removed the brackets filled the holes with caulk and then we taped
off all the windows and doors so I could paint the siding in the soffit using this airless paint
sprayer. And after the paint dried we removed the paper and tape and my brother and I put up some
new shutters. And at this point I did a little Mickey Mouse project and made some new custom
house numbers for the home so that I could actually receive mail. And for the last little
cosmetic project here I had to remove the front door because it was cracked in a few locations and
it was in desperate need of replacement. So I started by removing the brick mold on the exterior
and you're also going to want to pull off the trim on the inside of the door as well. You're likely
going to find a few screws attaching the door frame to the house and I recommend you just cut
through those using a sawzall. And after cutting through the screws I removed the entire door and
the frame from my home. So here's how we look in full summer jeep mode but I vacuumed out the dust
and debris from underneath the door measured the length for the sill plate and then I put some
construction adhesive down glued that pvc sill plate in place that's going to direct any water
away from the home. Then I flashed the perimeter of the door frame caulked around the backside of
the brick mold lifted the new door into place and got it positioned properly. And after shimming
everything out checking for level and screwing the door frame to the house I took some spray foam
insulation and I applied that all the way around the perimeter between the door frame and the home
and then cut off the excess. Then I painted the door this smurf blue color which you're going to
see throughout the rest of the video. And for the last cosmetic project I built this custom mailbox
which I think looks pretty good. Now let me show you how I completely transformed the front entry
way of the home. I started by removing the old flimsy metal railings by unscrewing them where
they attach to the house and then cutting them off where they were embedded into the concrete steps.
And after getting those removed it was time to power wash that existing staircase and I don't
know what it is guys but there's just something oddly satisfying about a good power wash. But
these stairs still look like crap so I decided to resurface them using this newcrete product and
I gotta be honest with you guys hindsight is always 20-20 but I really think I should have
just demolished this entire staircase and started from scratch. This is kind of lipstick I don't
want to say lipstick on a pig but it kind of is lipstick on a pig. It's just an ugly staircase
and regardless if it looks perfect or it looks crappy it's just going to be kind of unimpressive.
So I wish I did something different but if you stick around till the end you'll see that I think
I made the best of a bad situation. As the final step here I applied a sealer to prevent it from
staining and I'd love to get your feedback on all of these projects down in the comments. Now let's
get rid of this sidewalk leading up to the steps. So typically for a small sidewalk like this you
would just rent a jackhammer but I was able to get a killer deal for this guy online so we're
This was my first time using a jackhammer and after almost jackhammering both my feet
I got the hang of it. With my front walkway turned to rubble let's start thinking about how we're
going to repair it. So this is going to be two parts it's going to be the concrete landing and
then this curved sidewalk. I started by marking the outline of the concrete landing with some
spray paint and then you're going to go ahead and excavate down around eight inches. Four inches for
the gravel sub base and then four inches or so for the concrete sidewalk and I dug out some deep
footers that were below the frost depth in each corner to serve as the foundation for the porch
overhang I'm going to build at the end of the video. And after compacting the soil adding the
stone compacting the stone I built the concrete forms using some two by six and one by six lumber
staked it in place made sure it was square and then filled the entire form area up with some
concrete. We mixed all the concrete by hand using a drum mixer which was if I'm being honest a
nightmare but eventually we got it done. We finished the surface using a hand trowel and
then we gave it a broom finish. After letting it dry we removed the forms and I started prepping
the area for the curved sidewalk and to build the curved forms I had the guys at Home Depot
rip down four inch strips of hardboard so that I could get the curvature I wanted
and after getting everything level I compacted the stone installed the steel wire mesh reinforcement
and then I applied some WD-40 as a form release agent to the form. Now because I had a bunch of
issues with that initial pour and the mechanical mixer binding up I almost broke down and ordered
concrete to be delivered but I came across this product called the mud mixer which we used for
this pour and although lifting 40 pound bags of concrete over and over again still wasn't fun
this was a lot smoother than the drum mixer so we filled the entire form area with concrete
screeded everything smooth used an edging trowel around the edges to give us a rounded edge and
then finish the surface using a finishing trowel and then gave it the final broom finish before
adding a couple control joints to hopefully control where the concrete cracks in the future
if it ever does and I know that I'm going fast here but I have dedicated videos for all of these
projects on my channel and I also have this blog link down below that goes through everything in
detail and after letting the concrete dry I just removed the forms. Now if you remember that railing
we removed a few minutes ago now it's time to replace it so I used a laser level to mark the
post locations for the new railing and then I marked the locations for the bolts using a sharpie
after drilling the holes using a hammer drill and a carbide tip masonry bit I positioned the railing
posts in place inserted the expansion anchors and tightened them down preliminarily then I used a
post level to make sure everything was level and plumb used shims as necessary then tightened
everything down and cut off the excess shims. I had to cut off the excess bolts using a sawzall in
a few locations then I installed the post caps. This is the black cool railing system manufactured
by Musata and I basically just followed the manufacturer's instructions to install it. The
trickiest part was finding the angle there for when the railing starts going down the stairs but
after making that cut I just had to pre-drill the holes and screw everything together and although I
love the look of wire railings installing them is kind of a pain in the butt because you have to
install the hardware and tighten each strand of wire individually which can be pretty tedious but
eventually we got all the wires installed and got the tension just right. With the front entryway
complete let's turn our attention to some gardening and landscaping. Now if we rewind just a bit there
used to be a silver maple in my front yard and because it was rotting out and slightly leaning
towards my house I decided to hire a contractor to come in and remove the tree and then grind up
the stump. They left me with this beautiful patch of dirt which I'm going to fix later but now I want
to focus on the front garden. So here's a look at the front garden before we got started and the
whole idea is that we're going to add a new concrete curb edging as shown in green. I started
by removing all the old mulch and weeds to give myself a clean slate then I established my offset
from the house, marked the boundary and then I excavated down four inches, got the area relatively
level and then I compacted the dirt. After that I picked up my gravel sub base, set my depth and
then I added around four and a half inches of gravel sub base into the curb area. I also added
a weed barrier to hopefully prevent weeds from growing up in the future. After compacting the
stone with a hand tamp it's time to build the concrete forms and just like with the sidewalk
we're using lumber. To set the forms I double checked the offset from the house and then I set
the locations using stakes and I used a six foot level to make sure we were on track. Then I cut
six inch pieces of blocking to give myself a uniform spacing between the two boards of six
inches. That's going to be the width of our concrete curb. Where two boards met I used a
piece of bracing to make sure they were perfectly level and in line. After continuously checking
level I cut the forms to round the corner, used a framing square to make sure we were just that
square and then I completed the form area. In hindsight I wish I would have gone with a rounded
corner but the square corner I guess is what we're going to live with and just like the front entryway
I used rapid set 24-6 concrete mix and the mud mixer to mix all the concrete by hand. I used a
shovel to move the concrete around within the forms and then a finishing trowel to get it relatively
smooth to start. I also used a reciprocating saw without a blade to vibrate the forms to fill up
any air voids and because the mud mixer is on wheels I was literally able to roll down the
entire length of the form area filling it up with concrete. After filling up the forms with concrete
I took my edging trowel to give the edges of the concrete curb a rounded edge and then I went back
and cleaned up any of the hard lines with my finishing trowel. Because concrete will inevitably
crack I added control joints every four feet on center so when it does crack it'll hopefully crack
within that joint. After adding the rest of the control joints I cleaned up any of the rough edges
using a finishing trowel. Here's a look at the finished product right as the sun was setting and
then the next day I went and I removed the concrete forms. If you use a form release agent like WD-40
the form should come off really easy. And for landscaping I kept it simple with some low
maintenance evergreens and some black mulch. Next I turned my attention to the lawn and I started by
filling in the gap around the garden curb with some topsoil and I applied a bunch of topsoil to
the area where that tree was removed previously. Then I rented an aerator and aerated my entire
lawn. After aerating I did a bit of dethatching, removed all the weeds and thatch from the yard and
I planted some grass seeds spreading it around evenly using a seed spreader and applying it by
hand around the garden curb. After applying seed I sprinkled a bit more topsoil and I made sure to
water the grass. And while we wait for the grass to grow let's finalize this curb appeal transformation
with an architectural improvement. Although this house has come a long way from where we started
the haters down in the comments let me know that the house was still pretty ugly. And deep down I
knew that the house was missing something so I did some curb appeal research on Pinterest and then it
hit me. A gable porch overhang over the front door might solve my issue. So I modeled everything in
Sketchup and got to work. Now if I'm being honest with you I always had this idea in the back of my
mind which is why I dug those deep concrete footers at each corner of my concrete landing.
But before we install those vertical support columns we have to demolish the gutters and
remove some of the shingles above the door. I also had to remove that first sheet of plywood so that
I could access the front wall of the home which we're going to use to support our gable porch
overhang. After opening up the roof I determined the location for the vertical support columns and
I pre-drilled the anchor bolt hole using my hammer drill. Then I set the post anchors in place
installed the anchor bolt and tightened everything up. And before we get into the framing I want to
let you know that I have a completely free ebook that you can download. This is going to have a
cost estimate for this entire project as well as all these framing instructions in detail. For the
vertical support columns I went with six by six pressure treated lumber and we cut that to size
and positioned it in place inside the post anchor and then we tacked the horizontal board in place
to hold everything together temporarily. The next step was to cut another six by six to go
horizontally between the vertical six by sixes and we cut that and installed it off camera
unfortunately. After securing everything up top we permanently screwed the vertical support column
to that post anchor in the concrete and after getting that first portion framed we installed
a new piece of plywood roof decking so we had something to walk on. Okay so despite checking
the weather for uh days beforehand and checking the radar we had this blip of rain show up out of
nowhere so now we're at the tarp house. Murphy's law man anything that will go wrong can well
anything that can go wrong will go wrong something like that. Next we cut the angle on the ridge board
to a 4 12 roof pitch since that's the pitch of our roof and again if you want all the details
on how I found my roof pitch and a lot of the details for how we framed this you can check out
my free ebook everything is specified in detail within that. So as you can see there we had to
remove a few more of the asphalt shingles so that we were actually dealing with the roof decking and
then we adjusted the height of that ridge board to give us approximately a 6 12 roof pitch for the
gable and then I tacked the ridge board in place using my framing nailer and at this point I went
back to the front of the gable and I cut off all the overhanging boards to a consistent 18 inch
overhang and after that was done we installed the rafters. Now there was a little bit of math and
cutting involved to cut the rafters but essentially you're going to need to make a plumb cut that
matches the pitch of your gable where it intersects with the ridge board you'll need to
cut a bird's mouth cut where it intersects with the horizontal joist and then you'll have to make
one more plumb cut at the back end for the tail of the rafter. We made these cuts using a circular
saw and a jigsaw and once you cut one rafter you can use it as a template to mark all of your other
cuts and after nailing the rafters in place I cut the fascia board so that the angle would match
the roof where it intersects with the house and then I attached that to the tails of the rafters
and at this point it was time to cut and install the valley plate and the valley rafters and I
don't want to get too technical with this since I have a dedicated video and an ebook showing
exactly how to build this but the main takeaway for these is you have to cut the bottom of the
rafter at a beveled angle so that it sits on the valley plate properly and if you cut all your
angles correct it should look something like that. Here's a look at everything nailed together and
then we installed the plywood roof decking over top. Next up we installed pvc fascia trim on the
guys are getting some kind of value from this video I would really appreciate if you could drop
a like down below and drop a comment all the engagement really helps me out with the youtube
algorithm and I would appreciate it and although I was tempted to do the roofing on the gable myself
my entire roof needed to be replaced so I bit the bullet and just hired a contractor and with the
top of the gable complete I turned my attention to the underside and I first built this cage at
the back so that I could install tongue and groove soffit boards on both the back and the underside
of the gable and I also wanted to spice up the support columns so I decided to wrap the base
with this pillar wrap product that looks like stone. To install it you first have to shim out
the support column to give it a bit of additional thickness and then you glue and screw the panels
in place and you guessed it I have a dedicated video for that as well. Then I simply installed
the post caps and cleaned everything up with some caulk. There are a few more finishing touches with
this gable but I want to tell you guys a story in the meantime. So I rolled the dice and decided
to build this gable porch without getting a permit and I thought I got away with it because
like two or three months after the fact I still hadn't heard anything until one fateful day I saw
this notice on my door saying that this was not in compliance and I had to bring it up to code so
I had to retroactively get everything permitted which was a bit of a pain in the butt but
eventually we got it done and once I finished staining the underside of this gable this curb
appeal transformation is complete. Let's take a quick reminder look at where this project started
and here is a look at the final result. Now at the end of the day this is still a 1,000 square
foot rancher but all things considered I think we made the most lemonade possible out of a lemon
looking house at least initially. I would love to get your feedback on this curb appeal transformation
down in the comments and I'll try to answer every question that you guys have. If you enjoyed this
video please drop a like down below consider subscribing if you like DIY content and thank
you guys so much for watching. I'll catch you on the next one.