BEEREAL V3 Bow Build

Exploring Ancient Crossbows
3 followers
4 Video Views·Apr 26, 2026
BEEREAL V3 Bow Build
Comments are disabled for this video.
What's going on everyone and welcome to today's video. We are doing a bow build
on this brand new v331 and this is like the be real 31 black and yellow. I made
some like be real bows in the past and I really think this is gonna be it for the
v3 and this bow is gonna be my tinker, tinkerer bow. I'm hoping to do a lot of
shooting with it, messing around, probably won't end up hunting with this bow. Maybe
we'll give this bow away down the road, I don't know, but we're gonna get it set up
today, get it shooting, kind of see, see how it shoots. I haven't shot the 31
version in a little while. I've been shooting my 27 a ton, so see how it goes.
That is flat. That's funny, that was not like that. Okay, fun fact is a lot of people
think that when Matthews does a Proving Ground video and like how they send
bows out ahead of time that nothing actually happens, nothing actually
changes in the bows from when they go into full development, but that's not
true. Actually, this is just by chance, I don't know more people talked about it
or not, but this is my Proving Ground v3 which is in retirement now, but right
here on the lower mounting hole there, this, I'm explaining this badly, on the
sidebar adjustment this has a flat mounting surface, so on this one when you
mount it, it lines up 100% flat. Well on this one you can see, let me spin this
around, you can see it, it doesn't line up flat. There's this little bump right
here and I was, you know, I was just like hey is there any way we could just like
make that level and flat so that the sherd mount can go line up right
against it and they did that. So kind of funny, one little simple thing, but when
you, until you actually go out in the field and test it and shoot it and set
bows up, little things like that you don't think about and that is one cool
thing that Matthews does is the Proving Grounds instead of just sending it right
to Marfil. Alright so we're putting on the Ultra Rest Integrate MX. A lot of
people are wondering why I've been shooting like Hamsky, QAD, going back and
forth. Well this QAD system is just so dang easy to work on with these Matthews.
Like if you guys watch the 34 bow build, I literally set it up and the first
arrow was a bolt hole and I did not touch it. It was, we watched it even in
slow-mo afterwards and it was just like bullets, laser beams down there. They,
Matthews has like a pre-etched little marker. All you do is line up, line the
QAD arrow up with it a hundred percent and it gets you pretty dang close. Like
I'm gonna see how close we can get it without having to move the rest
hopefully when we paper tune. Alright here was our two beautiful holes out of
our 34. Let's see if I did as good of a job this time. I did everything exactly
the same so it should be close, should be real close. Alright not quite, we got a
little bit of a right tear. So what I might do this time is actually probably
gonna swap the top hats on the bottom this time because I know my rest is dead
center in the middle and that's really close. Like we should probably shoot it one
more time. Shoot it one more time for a little farther away. Yeah that's not bad at all
we can fix that. So I'm gonna swap the top hats just like that, super easy. You do
need a bow press to do this. You cannot do this if you don't have a bow press. You
can't really, I guess you could maybe do this if you had like one of those quick
bow presses. I wouldn't do it, it would be pretty sketch and I've done some sketchy
things. So let's do this with bows I should say. So you need two little tiny
allen wrenches. This is one thing I wish that they did was had some bigger allen
wrenches. Okay so the one side is just to just to keep it in place because it's a
rod in the center and there's like two screws on each side to keep it in place.
So you don't want to lose those. There's this little washer on the end, don't want
to lose that either. And then you take an allen wrench and there's a little lip
on the end and you take an oversized allen wrench so it's like bigger than the axle
hole. You just kind of bump it right out and boom there's your axle right there. So
you don't want to lose that either. Put your allen wrench out and then your cam slides
down and just kind of keep it, keep it right there. That's why a bow press is so important.
So now all you do is, there's another little lip right here and you just take your allen
wrench and tap it and it slides right out. So this little part, section, this lip is
the spacer. So why Matthews is really awesome is instead of messing around with little tiny
spacers it's called a top hat. You put it in each inner side and there's different spacers
and you do that to mess with your left and right adjustment of your string. Super neat
little tool that not a lot of people mess with but it's a great tuning tool. So all
I'm doing, there was a skinny one on the left, fat one on the right. So I'm going to put,
I'm just going to switch them essentially and I'm going to bump, that's going to bump
the cam to the right which I think will help with my right tear. I think. I always get
the mind game messed up when dealing with this so sometimes it takes a couple times.
A couple love taps with a screwdriver. You see I just shoved it in the opposite way that I put
it in. It really doesn't matter which way. It does have yellow loctite on this so if you're
worried about these ever backing out you could always replace with a little or put some fresh
loctite on that. And these screws you do not want to tighten down super hard. Like I never
change them from this position, like the long position. And all I'll do is just finger tight
those down. And that's it. We just bumped our string alignment slightly to the right. And you
only, you can do them the same, you can do one, you can not do the other. There's no wrong way
to do it. You could change them and mess them all around and you'd be fine. So let's see. Okay,
I think that's a little bit better. We're gonna take a step back. Nice. That's really close.
Really really close. But we are gonna bump the rest. We're gonna bump the rest slightly to the
left and shoot one more time. There we go. I might still have a little bit of a right there.
And just a smug, I might do a couple more clicks. That looks pretty dang good. I'm using this paper
that's a little bit thicker than I'm liking. So what I've been doing every now and again is
getting a finer piece of paper, like wax paper, and you can see every little thing. Like that's
a bullet hole. But if you were being really nitty gritty, you can maybe get that a little bit
cleaner. But you won't, you really wouldn't be able to tell if you had a lighted nock and shot
that a hundred. You really wouldn't see anything in it. Let's get a weight on this real quick.
Came straight from factory. 75 pound limbs. They always run a little high, but it's 76.3. So that's
good. I'm gonna leave this one just like this. But we're gonna go run inside and eat dinner,
and then we're gonna come back out. The winds gonna die down a little bit, but we're gonna
shoot this thing and see what it can do. Alright, welcome back everyone. I'm really excited to
shoot because it's a super calm day. Just inside, I got my left and rights. You can get your left
and rights aiming at a very close target because no matter if you're five yards or a hundred yards,
your left and rights is, you can get it dialed in. It just shows more at longer distances. But
we are, we are at about 30 yards right here, and I'm hoping we can walk back. I'm hoping to get
maybe 80 or something with this setup and see what type of groups we can get.
The V3, it's after shooting the TRX-34, which I'm very impressed by that bow. But
this bow is just a true hunting bow. It's quieter. It's a little bit faster. I can tell. Oh,
we could shoot it through the chrono before we're done. It is a little bit shorter Axial Axial M34,
but it's got that long Axial Axial feel because of the giant cams. But I'm not going to talk
about the V3 because I've already done a ton of videos on it. It's a killer bow. We're just
going to shoot it. So I'm going to walk back, shot a little high, so it should be good.
Nice. This bow might be over 300 feet per second. That's really fast. I don't have to move it very
far, but let's go pull them and then try to squeeze back here and get to 80 and just see
what type of groups we can get. I'm holding really steady on the target. So I think this
thing is going to be a pretty good shooter. Okay. So it is 80 yards and that last one,
I'm actually super impressed with that last one. All four were in a group about like that.
So we're going to shoot one more time. It's getting dark on us, but this bow so far set up,
it's been super good. I'm super impressed with that grouping 80 and it, how it's holding and
shooting makes me feel like I can do a little bit better, especially putting some time behind
this bow, breaking it in a little bit. It'll definitely be a shooter. Hi everyone. Not a
bad group. 80 yards. These three for sure a good group. Maybe I was just, my sights a little low.
This one kind of felt that one shanked out to the left, but this is like my fifth end, I think
fourth or fifth end, a couple ends getting, getting sighted in, but off to a really good
start. V3 31 definitely is a shooter. And I know I talked about like the 27 is such like a compact
white tail saddle hunter tree stand bow. If you're under like that 29 and a half inch draw,
it's like money and it still shoots super good long distance. And 34 is kind of like that. If
long draw hybrid type hunter, but this one, this one, if you're drawing is anywhere from 27 and a
half and up and you like to target shoot, you like to hunt, or you just like a longer axle,
axle bow, you really can't go wrong with this one. It's definitely going to be my tinkerer
and my fun shooting bow this summer. Probably will take it to a total orchard challenge.
So we'll, we'll just get dialed a little bit in the next few weeks and she'll be good to go. Get
a sight tape that actually works and fletching the arrows and literally probably won't touch
anything on this bow. Just run it exactly how it is. So thank you all for watching so much. I
appreciate every single one of you. If you want a hat, we got a bunch of new hats in stock and
most of them are in stock. Check them out at b-rollmerch.com. Make sure to subscribe,
like this video, leave a comment, and we will talk to you guys next time.
