I Recreated a Traditional Ojibwe Bow

The Saga of Past Longbows
6 followers
5 Video Views·Apr 20, 2026
In this video, I recreate a traditional Ojibwe-style hunting bow — this time for fellow YouTuber North02.
The Ojibwe (Chippewa) people were known for practical woodland hunting bows built for survival and efficiency. My goal was to stay true to the historic design while crafting something functional and worthy of being used.
In this build:
• Wood selection and layout
• Shaping and floor tillering
• Final tiller and weight
• Shooting test
Building a bow for another creator adds pressure — it has to perform.
Let me know what historical bow you want me to recreate next.
Here’s another video similar to this one!!
making a Cherokee war bow(start to finish)
What's up everybody? Today we're going to take a log just like this one and recreate a fully functional replica from ancient history.
I'm going to be using this example from the Encyclopedia of Native American Bows and Arrows.
It's a 56 inch long ash flat bow with a single knock on one side and a diamond knock on the other.
It was also painted with red, blue, green, and white on the back, belly, and sides.
The bark was removed from this log a while back.
I'm going to use these wedges and a hammer to split this to get it closer to the dimensions that I want to get started with.
This stave is split very straight, which means that it has the quality that we need in the grain to make a good self bow.
I then use a pencil to draw the rough outlines of the bow.
These are just kind of guidelines to go by.
Here I use a bandsaw to get it a little bit closer to the dimensions that I drew on it.
I normally would just take it out with a draw knife for this, but I was having a bit of back issues, so I decided to take it a little bit easy on myself.
But once I get it close, I switch to the old draw knife and chisel.
This chisel is for the handle section, if you notice.
I sawed a little curve right there down to where I want the handle to be, and then I just chisel it out from each side.
If you look closely, you'll see some minor cracks in the limbs.
As long as they don't go off the edge, they'll be fine.
The limb that I'm steaming had a slight amount of deflex towards the tip and a little bit of a twist.
So you see me applying downward pressure in a twisting motion to fix that once the wood has been heated by the steam.
And once it cools, the wood stays.
We got enough wood removed now. We're starting to bend very slightly.
I'm going to draw another guideline so I don't go too far when I keep removing wood.
But for right now, I'm going to go ahead and do the nocks.
Now we can really begin to tiller this thing.
You can see the stiff spots, and I marked them using a pencil.
So now I know I need to remove wood where the pencil is to make the bow bend more evenly.
And since the bow is too heavy to draw, I need to remove wood from the entire limb as well, on both sides.
With a 32 grit belt, this thing's basically a rasp on wheels. It removes wood pretty quickly.
Our left limb's bending pretty good.
Right limb's a little stiff in the mid.
We're almost to brace.
That's a lot better. We're getting there now.
Well, she's ready to be braced.
With the brace, it appears that this limb is slightly stronger.
So let's take this limb down, and then we'll brace it a little bit higher.
Let's put it on the tiller entry.
So after putting it on the tiller entry, I think it's pretty obvious where it needs to be.
You don't even really need to pull it that much.
So on this limb, on the left limb, it needs to go down right there.
On the right limb, it's about the opposite.
It needs to go down right there.
So I did some wood removal, which looks like this.
There's 22 inches of draw.
It's not terrible.
A little tricky on this. 23 inches of draw.
Let's exercise these limbs.
Looks like my handle's finally starting to bend a little bit.
We're hitting 24 inches now.
Get that handle bending a little bit more.
I can get some more out of it.
I think 25 was the goal, and 25 is what we're going to get.
Man, we're getting close.
Okay, so off camera, I have made a white bowstring out of modern material.
I made it white so it would look like sinew, which is what it would have been made out of back in the day.
But I don't know if North02 has the experience with real sinew bowstrings with a lot of maintenance.
So I just made them a modern bowstring with material that looks like sinew,
and it'll grab great performance with way less maintenance.
Yeah, it looks good.
Now for some final shaping on the old handle.
Although the tiller's looking pretty good, the weight of the bow overall needs to come down so I'm still.
So here I'm just going to take a bunch of scrapes off of each limb using a knife,
being sure to count exactly how many scrapes I take off so I can do an even amount on both limbs.
Let's see how she looks.
56 pounds.
Now we've got to shoot it in and make sure the tiller don't change.
Sorry, you've got Batiste to bottom there.
I had to turn the camera around because it kept falling, but you'll have to forgive my poor shooting.
This draw length is about four inches shorter than mine, so I can't even reach anchor.
So I'm just kind of shooting blind here.
But don't worry where I'm hitting, just look at the speed of the arrow.
And it is quick.
Just a little speed test with a 530 grain arrow.
It's no speed demon, but it's definitely enough to take deer.
This is just my maker's mark and a little thing saying that it's 55 pounds at 25 inch pull.
I'm no artist, but now it's time to make my best attempt at matching the paint job from the book.
Traditionally, pigments from rocks or plants would have been mashed up and mixed with animal fat and used to paint and seal the bow.
Although I have used animal fat to seal bows before, I've never made primitive paint.
So I'm just going to use acrylic paint and then seal it with a satin finish polyurethane.
I know that's not primitive, guys, but I'm out here doing my best. Come on, give me some slack now.
And after a few coats of this, it's time to shoot it.
Overall, I'm really happy with how this bow turned out.
I'm excited to see what he's going to do with it.
If you want to see more videos like this, check out my channel.
Thanks guys for watching.
