This video shows how I scraped my way through the old, brittle finish on this mid century dresser, down to the raw walnut and nourished it back to life. This project took approx 2 days to complete.
This piece belonged to Andrea's grandparents; it was purchased by her father in 1962. Canadian made by VicArt, this gorgeous walnut dresser was unfortunately temporarily left in an unheated house for a few years and had mice making their home in the drawers. Luckily, we managed to salvage it and the matching tall dresser, as well as a headboard/footboard.
If you love furniture flipping, vintage wood restoration, or relaxing paint or no-paint makeovers, make sure to subscribe and check out my other channels: ❤️ @TFGUnplugged – Raw, ASMR-style restorations ❤️ @tfgsnacks – Short-form, quick makeovers
Want to support the channel or shop my tools? See below! ✅Social Media Links & Ways to Support the Channel (Buy Me a Coffee, Amazon Wishlist, etc: https://bio.site/tfg 📫 To send mail: Transcend Furniture Gallery, c/o Angie, PO Box 718, Hantsport, NS, Canada, B0P1P0
💡Shop Towels https://urlgeni.us/amzn/TFGShopTowelsCA (Canada) https://urlgeni.us/amzn/TFGShopTowelsUS (US) __________ NOTE: Please be advised that the links provided are affiliate links and I may get a small commission from qualified purchases. This is at absolutely no extra cost to you! Always be sure to read all manufacturers instructions and use appropriate safety equipment when using any of these products, and do so at your own risk. ______________________
Hello everybody, welcome to another video. This piece is a little bit special because this isn't
a piece that I'm flipping to sell. There was a little mouse family living in it and it was
in a house that was unheated so there was a lot of humidity and moisture. My partner and I got
it out just in the nick of time and I'm hoping I can save this. It's not in terrible shape but
it absolutely needs attention. This actually belonged to her grandparents and they were
the only owners of this dresser so there's a matching headboard and another dresser that
I'll get to at some point. It is Canadian made by Vicart and has absolutely beautiful walnut veneer.
I have a ton of scraping to get to so let's get into this video. My name is Angie and I
refinish furniture. Sometimes I paint and sometimes I don't but I always do what I
can to save old pieces from the trash. Welcome to my workroom. This piece and its matching
pieces actually were very well taken care of for the majority of its lifetime. Unfortunately,
after my partner's grandparents passed away, the house, due to multiple family issues, remained
vacant for a couple of years with no heat and as such it was left exposed to a lot of moisture
and unfortunately rodents that were nesting inside the drawers and chewing up some of the wood.
It could have been a lot worse. I think, like I said, we got it out just in time to save it.
We also managed to salvage this really cool 1960s couch. It's a sectional and that little
bit in the corner actually spins for hidden storage. It was really really musty smelling
but we hit it with abyssal a couple of times and it's good to go now. But back to the piece at hand.
It's a very well made piece. The drawers themselves are really well constructed.
You've got double dovetails. You've got a hardwood drawer construction. Pretty much
everything on this piece is wood and wood veneer except for the substrate underneath the top.
Basically it is a walnut veneer and some other type of veneer sandwiching pressed wood. So you
can see there is a slight dip to it. It's a pretty common problem with these older pieces.
I don't see drawer pulls this color very often so that's kind of neat. And what also is a bit
strange is that on the top here if I spin this around you can see there is a machine screw but
at the bottom you can't see anything from the back. That bottom pull is actually screwed in.
I have no idea why but just I don't know it's kind of cool. So back to the wood grain here.
Pretty much every face you see on this piece is walnut veneer so I'm going to be scraping it.
I could have used a chemical stripper. It would have made really quick work of this but it's a
bit messy and the finish itself was a bit brittle so I knew that it would scrape off pretty quickly.
The veneer on the top stops right where it hits this edge so I have to be really careful
scraping here that I'm not catching that lip and pulling it back toward me and splintering
the veneer. A lot of people are a bit afraid of these carbide tip scrapers and while it definitely
does take some practice and finesse as well as determining exactly which way the wood grain is
going because you definitely don't want to scrape against the wood grain, they're not difficult to
use. You just want to make sure you practice on something that maybe isn't a family heirloom first
to kind of get the hang of it and know your limits with it. But on some of these old shellac
and lacquer finishes it just removes the material so quickly and easily and it's fun. It reminds me
of woodworking with one of those old school hand planes. There's something very
physical about it and it's appealing to me. So right up against the edge of the side here you
can see there's still a little bit of finish I couldn't get with this scraper because of the way
the handle is. I can't get right up close to it but this little detail one I can because there's no
obstruction there. Slow and steady wins the race with this for sure. If you saw the video a few
weeks back where I introduced my new surf prep, I actually haven't used this since then and I
haven't used it yet on a full piece, only on part of a piece, so I thought that this would be a good
piece to try it out on on big flat surfaces and just see how it compares with my five inch random
orbit sander. One thing that does give this an edge over my dewalt is that it has four straight edges
and I can butt right up against these edges here. I have to say I was pretty impressed. I used a
fairly fine grit here. I think this is a 220 and I went right to 220 because I had already gotten
most of the finish off. I didn't want to remove too much of the veneer and I wanted to play it safe
because I know that the sanding pads for the surf prep are a little bit different than normal sanding
pads. I was really really impressed with how quickly it worked and also the dust collection
is great. Now I do have a Festool dust collector and they're pretty good on their own but I just
find the way the surf prep is set up, it does really minimize the dust that gets left behind
by the vacuum. I need to take care of that dark stain on the top so I'm using some hot water
and oxalic acid to try to bleach it out. Oxalic acid is basically a wood bleach. It doesn't
work the same as regular household bleach. In most cases regular bleach isn't going to work
but oxalic acid, it's a little bit hard to find locally. At least around here I order mine online.
Basically you just mix it in hot water and you apply it to the surface. You need to apply it to
the entire top surface. For example I couldn't just put it on the stain or it would leave a
very obvious light mark. So you apply it to the whole top and with stubborn stains I like to use
a nylon bristle brush to really get in there and try to loosen that stain up. Basically what the
oxalic acid does is it breaks down organic compounds which essentially breaks up the stains.
While the oxalic acid is drying completely on the top I'm getting to work on scraping the sides.
The oxalic needs to dry completely and then needs to be rinsed off so I'm taking advantage of this
time to work on other areas of the piece. This piece is a bit unique compared to most of what
I work on in that the legs are part of the side. So basically the frame of the side here is
constructed out of solid wood and then they put a walnut veneer on the side. But doing it that way
leaves this piece at the front of the back leg and the rear of the front leg that the solid wood is
exposed and the wood is a different color. So I'm going to need to stain that when it comes time to
finish the piece. Once the oxalic acid has completely dried I'm pretty liberally adding
some water here. I'm technically going to rinse this twice and then use a dry towel to get up as
much of the excess water as possible and let that dry. I am very happy with how this stain came out.
You can see here because these are matching pieces of veneer we've got a great match here
and there is no more dark stain. Time to get to work on the drawers. There are nine drawers in
this piece and they need to be basically scraped, sanded, cleaned out, inside and out, top to bottom.
I'm using that same Baco scraper to remove the finish from the top.
You can see it jumped a little bit here and that is because
my drawer is not perfectly stable. So you can see once I hold it here hold it steady it comes right
off. This scraper worked great on these ledges here on the bottom of the middle drawers. You
get right down into the corner and then when I go to sand it with my surf prep because it does have
those flat edges I'll be able to sand right up to this corner. You want to be really careful when
you're scraping the edges of drawer faces like this because sometimes they will put a band of
veneer along the edge and often when they do that if you're scraping down across the top you can
catch the edge of that edge banding and rip it. But in this case the veneer is actually sitting
flat on top of this solid wood drawer face so I'm able to literally scrape right off the edge and I
don't have to worry about chipping any of the edge banding because there isn't any. The bottom drawers
have beautiful walnut wood grain but it's in a different direction so as you can see here I'm
following the direction of the wood grain with my scraping. If I were to try to pull the scraper
across the length of the drawer like I did on all the other ones I would chew this veneer up in about
two seconds. Now that everything's scraped it is time to clean out the inside of the drawers.
This drawer in particular had the worst mouse nest. Obviously we cleaned a lot of it out when we
picked up the pieces a couple years ago before we put it in storage but it hasn't fully been
cleaned out so that's what I'm doing here. I'm using a bleach cleaner. I don't want to take any
chances with what could be in here. I've got gloves on and I'm using a scotch brite pad to really scrub
into the wood. I'm going to rinse it with some water, dry it out and then set it in the sun to
basically bake for a couple of hours while I work on other drawers. Once I have the insides of the
drawers all cleaned out I'm going to get to work with sanding. I'm using the surf prep again with
a 220 grit sandpaper. For years I referred to this surf prep as a fancy sander that I didn't need
and honestly I did just fine for the first three or four years without it. I had so many people
saying oh you have to try this sander that I finally broke down and bought one and I'm really
glad I did because it does fill some holes and some gaps where my dewalt just isn't as practical.
If this is a sander you're thinking about getting you can actually use my discount code to save
yourself 10% off your order and I will link to that down in the description below as well as
flash it here on the screen for you. For the areas of the drawers that were actually chewed by mice
I just used the sander here to gently round it over. Again this is a piece for us it's going to
be going in our guest room so that is fine with me. I did sand down the drawer bottom as well to
see if that stain would come out. It didn't which doesn't really surprise me so I thought I would
try a little bit of oxalic acid. I wasn't super hopeful but you know I had to give it a go.
Even though these front pieces here aren't actually seen when the drawers are closed I
decided to give them a quick sand and clean up anyway.
And on this side of the dresser I had to round over those mouse teeth marks anyway.
I just decided to sand it all and I will use some General Finishes
gel stain in the color antique walnut to re-stain these boards.
But just before I start staining it is finally time to give the inside of this piece a really
good vacuuming cleaning. You guys know I love my Otis oil so of course that's what I'm choosing
to finish this piece with. I'm not going to be staining any of the walnut the only reason I
stained those boards that separate the drawers is because they're a different type of wood.
I'm using these Merkur Merlon pads and as always I cut a full sheet into four individual sized
pieces and usually one piece is good enough to do a whole dresser. Otis is not a typical oil
like when you think of something like Danish oil or hemp oil it is completely different from those.
It belongs to a family of finishes called hard wax oils and as such needs to be applied a little
bit differently. The reason we use these non-woven pads to apply it is because it has to be really
worked into the wood it has to get into the pores and really coat this wood. I've had quite a few
people say oh it's so expensive and sure it is when you first purchase it but a little goes a
really really long way with it so that little jar even though it may cost you
whatever it costs you where you live you're gonna get a lot more out of that one tiny jar than
sometimes a gallon of normal finishes. One jar of Otis could probably easily do oh my gosh I'd say
seven or eight dressers this size. There are multiple reasons I like Otis oil over traditional
polys. One it's completely food safe it's non-toxic it smells delicious you can get it on your hands
without worrying about it burning your skin off. You don't need to wear a mask while you're
applying it it brings out the natural beauty and depth to the wood like no finish I've ever seen.
Best of all it's extremely easy to touch up if you have a little accident down the road where
you scratch something you don't need to re-coat the entire surface you just re-coat the area that
got scratched. If you're wondering where my tattoos went these aren't my arms Andrea happened to come
home at pretty much the time I was about to start cleaning the hardware so she's helping out with
that and Willie Hatfield who is our other tabby you guys have seen Willow a few times this is
Willie he was just making sure everyone was doing a good job. I usually leave the Otis oil on for
about 45 minutes to an hour before wiping it off so while that is doing its thing I'm going to
stain these little bits I told you about earlier where the actual raw wood of the substrate is
exposed and then finally it is time to wipe off the excess Otis oil the less oil you use
initially the easier this part is. Now with the hardware we actually talked about maybe spray
painting them a matte black I thought it would look really nice with the reddish tones and the
walnut but we opted to leave them original let me know in the comments below what you think if you
think leaving them as is was the right decision or if you would have painted them black just for
some contrast I used this mohawk touch-up marker to just kind of deepen the color in this groove
and put this piece back together this was absolutely a labor of love if this piece and
its matching pieces had stayed in the house much longer they absolutely would have been
trashed I'm so happy to have intervened at the right time don't forget to hit that thumbs up
if you liked this video and please subscribe if you like this sort of content I try to put out a
once a week thank you so much for watching