Intro to Power Amps - AudioTech

TheGospelGuitarist
1 follower
Mar 31, 2026
An introduction to audio power amplifiers.
Hi, Gospel Guitars here with another installment of Audio Tech.
Today we're going to discuss a little bit about power amplifiers.
After showing you the house rack in the last video, I just thought I'd bring
out this rack. I keep running into more pieces of
equipment to show and talk about. Every time I think I'm done, I go, oh
forgot to do this. So power amps. They're very simple on
the front, and this is my rack setup. I use the
Behringer 15 band, as I mentioned in my video earlier,
for EQing the monitors on stage. So as you can see, I can have two
separate monitor systems. And then I have one
power amp at the moment.
It always would be helpful to have more than one of these
available in case one goes down. You can just
move the cables and you've got a backup in your rack.
But be mindful, these things weigh a ton, okay.
Today they're coming out with the newer models. They are dropping
weight quickly, and I would advise saving up for a
newer model by some of these companies out there
where their power amps are very powerful and yet they're very lightweight.
The older amps just are really heavy. This one's not
too bad, but it does weigh. It will work you out
if you've got to carry it for any distance. So you're going to want to have
some proper carts to transport your equipment on.
Now you can run it where your front of house is running left and right
for each side of the amplifier, but more often than not,
a lot of people run it the way I'm running mine,
where I just daisy chain the front of house speakers. I don't run a stereo
setup. I run a mono setup. It's a lot easier to deal with
and everybody hears everything. So this side is running the front of
house. So when I turn, usually you basically want to run them
wide open anyway so the amp can breathe and you've got plenty of headroom.
But if you find it's just overpowering for your situation, you can always back
it off. I almost never run them past
the nine o'clock or three o'clock position on mine
for anything I've done, and I've done shows up to 300 people.
This side I'm using for the monitors, and it also powers two monitors.
And also on the front of your amps, you're going to find clip lights,
signal lights, and any other extras on mine.
I have a special processing system that Yamaha makes for Yamaha speaker systems,
and that lights on when it's engaged. But that's pretty much it, on and off
switch. So basically, you know, protect lights
and temperature lights. There's all kinds of warning lights on the front of your
amps, so that's pretty straightforward.
Okay, why don't we swing it around and take a look at the back.
Okay, on the back of the amp you're going to find a lot of options for
inputs and outputs. All amp manufacturers
generally will give you quarter inch and
mic line inputs. They will usually give you quarter inch
and these twist lock connectors, okay, for your outputs.
Now this amp has a couple other options which are nice,
but another thing that you'll find on the back of your power amps is your,
most of them are set up for bridging. You can run them in stereo, or you can
run them in parallel. So my way of looking at it is bridge is
just running all the power of both amps, so you have a
really high output, but it's in mono. When you run it in stereo, it's your
typical left and right division of the power amp, and in parallel you're
actually using the two power amps separate from
each other, so they're running independently.
On this power amp, it actually has a low cut
and a frequency where you can select where you want it cut off. So if you have
a lot of standing low frequencies in a room,
I can actually, you know, dial off like at 110 or so.
If I'm having standing waves at 80 or 90, you know,
hertz, I can dial them out of the system right here without even touching my EQ.
It has a subwoofer setting and an off setting
as well. Not all of them have that, and then I have my YS processing on
and off on the Yamaha system, which is designed for your Yamaha
systems. I have Yamaha speakers, so I leave that on all the time. Gives them a
little bit more response. So as you can see, you have
different types of speaker connections that you're going to want to take into
account when you're building your sound system.
Some other things you need to consider is the actual
output power of your amplifier. You want to know what you're going to be
doing. What are you covering? Are you a rock band?
Are you just an acoustic ensemble?
I cover basically acoustic ensemble type stuff
and speakers, so you have, you know, someone
evangelizing, and that's what I do with it. I don't cover any,
you know, rock band type scenarios. This would probably be just used for
the monitors alone if it was a rock setup, and I'd have
another big huge power amp with a whole lot more power than this thing gives
to power the front of house, plus I'd have subwoofers
and power amps for those. So you really need to design your system based on what
it is that you're doing,
and then buy the appropriate speakers and power amps so that they match. So the
output and the ohm ratings on your outputs of your amplifier will match up
to the specifications of your speakers. And you want to be careful, as I was
mentioning earlier, I'm running two speakers on the A output for the
front of house, and I'm running two speakers on the B output to run my
monitors. So I have to know what this thing will
handle before it blows up on me, as far as how many ohms, what the ohm
ratings are on the power amp, and what the ohm
ratings are on my speakers, not just individually, but when I pair them
up. So when I take, all my speakers are eight
ohms, so if I run two eight ohm speakers on front of house,
chained together in series, so I have one speaker here on one side, one
over here, and the cable goes from the power amp
to the left speaker, from the left speaker over to the right speaker. That
would be in series. In parallel, we'd be running this output
to the left speaker and this output to the right speaker.
In series, what you do is you take the eight ohm speakers and you divide it by
two, so that'll give me a four ohm load on this amplifier, and that's as low as
this amplifier will go. But if I had two four ohm speakers,
I could not line them up in series, because then I would have a two ohm
load, and this will shut down. It will go into protect mode
and quit. It won't power it. Two 16 ohm speakers will run at eight ohms,
so you have to look into all of the different
mathematics that are involved in it. There's a million sites out there
that can go in detail with all of those types of wiring schematics, but you want
to read up on the power amps that you're
interested in buying, and once you decide on how much power
you actually need, how big of a house are you planning to
work in, and then match the speaker systems
appropriate, or vice versa. If you're going to do a
big house, you're going to need a lot of big speakers,
so you're going to need a lot of big power amps.
If you're running smaller venues like I do, you can go with
a smaller speaker system and a smaller power amp,
and you can even get away with one like I am here. I'm running
four speaker systems on two sides of one power amp,
and it serves me very well. I have no problems with level
at all. Matter of fact, I never have maxed the system out.
But that's just a little bit of things that you need to think about
when it comes to designing your sound system and
what you may come across on the back of a power amp. If your power amp is built
into your mixing board, then you will find these types of outputs
and connections on the back of your mixer, and they will
look like these. These would be your speak-on connectors for your speakers
and quarter-inch connectors. These inputs would not be there because
they're internal. They're already inside the mixer,
but you may have some bass roll-off and some subwoofer connections on the back
of your mixer, and you'll probably have a fader just
dedicated strictly for your subwoofer.
So it would power that as well, and then you have to look into how your
mixer will handle what kind of speaker systems you need
to buy for your mixer and match it that way.
But just keep these things in mind and keep them aware.
Be aware of them. So that covers the power amp section.
I hope you found it helpful, and be real mindful of these things because
you don't want to blow up speaker systems by using the wrong power
outputs, and it's not bad to have more power here than your speakers can handle.
People always think you're going to blow up speaker systems if you have
something that's more powerful than your speaker.
All that's going to do is give you headroom so you have less clipping.
The clipping will destroy your speaker. It's not the amount of power that's going
into a clean. You can run a speaker pretty hot
if it's clean power, but once it starts distorting on you,
now you're going to burn out speakers and power amps. So it's
it's not a bad idea. Actually, from what I understand, it's worse to have an
underpowered speaker system because then you will push it into...
you're trying to get more power out of your sound system, and you're distorting
the power amp, which is distorting your speakers, and then things melt down.
People are like, I fried my speaker system and my power amp was
underpowered. How'd I do that? It was because of the distortion in the
wire. You just got it too hot. Distortion equals heat,
and heat melts things, so we don't want to do that. So make sure you have a power
amp that's way more than sufficient for your sound
system, and be willing to spend the extra money
on these guys, and don't go cheap because your whole
sound, your whole gig depends on your power amps.
So you really want to make sure you got quality there.
So that's it. Thanks for watching, and have fun building your system.
