Only One Of These Will Ever Exist

Make Handmade Furniture
3 followers
1 Video View·Apr 1, 2026
AI Generated·May contain errors
Hey everyone, this is Nick from Padula Studio based in Sydney, Australia.
And in this video I'm going to show you how to sculpt a piece of furniture and why this
simple technique is almost impossible to get right.
So the piece of furniture I'll be making is a custom designed coffee table.
And like with every project, the first step is board selection.
Now you always want to choose your best boards for the areas that will be seen the most.
And in this case, because it's a table, the tabletop is the area that I want to focus
on here.
The 3mm MDF template is the exact shape of the top I'm after.
And although this template's main use will come later on when it comes time to shape
the top itself, it's now going to come in handy while I pick the best part of the grain
to show off on the tabletop.
So this amazing looking wood is an Australian native called Tasmanian Blackwood and has
been supplied by Britain Timbers.
I'll leave a link below to their website if you're keen to check out a list of timbers
including more Australian species.
Now the machine you just saw me using is a machine I get asked the most about, which
is fair.
It's not a standard machine you see in workshops.
This is what you call a slab master.
It's made by a company here in Australia and I am quite apprehensive when it comes to talking
about this machine as it is quite dangerous.
But I'm sure you can Google it and find out more for yourself.
Now as we go through this video you'll find out that this sculpting technique is a great
way to use your offcuts as it uses a process called stacked lamination, where you basically
stack wood on top of one another, similar to laying a brick wall.
Then simply carve away the laminations creating your shape.
But this will all come to life later on in the video.
The glue that you see me using here is a polyurethane glue.
Now you're going to see me using a combination of glues in this video and even though I normally
use polyurethane glue in my tabletop glue-ups, it's imperative to carefully select your glue
when using Tasmanian Blackwood as the acid catalyst in some glues turn the Blackwood
green, making it very difficult to sand out.
Type 1-3, which is my usual go-to glue, is one of those glues that don't respond well
to Blackwood, but this polyurethane glue as well as type 1 original work well.
So one of the questions I get asked the most about over on my Patreon account is my process
from design to construction.
Do I have a plan or do I make changes as I go or do I just wing it?
And the answer to that is I have a plan from the very beginning.
I always work out the final design in Sketchup before I order my materials and in some cases
I'll build a model and from here I will strictly work according to that plan, at least within
reason as sculpted furniture tends to have a mind of its own.
But I always do my best to work out the proper sizes and designs of my pieces to help minimize
mistakes during the building process.
This also helps to create less waste.
Now in most cases I'll make multiple iterations of my designs to ensure I have the best version
possible.
But because I've been asked this question so many times, it got me thinking maybe I
should try and wing it and go with the flow.
I am someone that likes a challenge, why not just wing it, yeah, go with the flow.
That sounds exciting and spontaneous.
Man I can actually see the red flags as I'm saying that.
Needless to say this didn't go quite as according to plan or lack thereof and to be honest I
feel like I've proven to myself why I like a plan to stick to but we'll get to that shortly.
So Tasmanian Blackwood can range in colours from dark brown to a lighter pinkish tone
and in my opinion a stacked laminated piece like this can look a bit disorientating if
these colours are scattered around.
So I decided to create a gradient or an ombre pattern to help transition each colour into
one another, hopefully creating an even pattern.
Now I know I said I was going to wing it on this one but when I came up with this gradient
idea I just couldn't help myself.
In order to get the best yield out of my material I had to create a simple profile of how this
ombre pattern would work as you can see here.
Like I said earlier this process of laying boards on top of one another is called stacked
lamination.
This is a technique made popular by a furniture designer named Wendell Castle.
Now I remember seeing a photo of his work years ago which absolutely blew me away.
My entire view of furniture changed in that moment.
It was almost as if someone had handed me the key to an entirely new world of furniture
making.
I strongly suggest checking out his work.
By stacking boards on top of one another you are able to create an endless form which will
allow you to sculpt whatever you want.
So now I'm at the point where I need to glue each row together and of course it's important
to ensure that each join is dead flush with one another.
So I'm going to use a piece of toughened glass to help keep the boards flat.
As well as some salt, believe it or not.
Normally you would use biscuits or dominoes to line the joins up but because I'm carving
into the piece I don't want to run the risk of carving into the connectors.
Now I'm sure you would know that when you glue two pieces of wood together the glue
makes them slide around.
Adding a small amount of salt to the join at each end stops the boards from sliding
making this entire glue up process much easier.
Now you're not salting your fries here, you only need a tiny amount of salt at each end.
Like I said earlier I'm using Titebond original as it doesn't turn the black wood green and
the reason why I'm using this glue instead of the polyurethane glue is because I want
to clean the glue up before it dries.
Polyurethane glue foams up making it harder to keep the joins flat whereas I can simply
wipe away the Titebond with a damp cloth.
I mentioned my Patreon account in my last video and since then another 100 patrons have
signed up which is absolutely mind-blowing.
So a big thank you to all of you.
I'm a firm believer in providing value for your money.
After all I build furniture for clients that pay a lot of money for their pieces and I
feel the same way about my Patreon account.
If you're going to spend your hard-earned money then you need to get something of value
in return.
The content is free from algorithms and the extra behind the scenes and monthly woodworking
videos give an insight into my 20 years experience in the industry.
I've just started posting regular tips and tricks videos where you can get an insight
to builds like this coffee table in real time as I'm building it.
Plus you can get the extended 50 minute version of this video with no voiceover or music just
shop sounds.
And I've just posted a video about how to start a woodworking business.
So if you'd like to support my work and get a heap of extra woodworking content check
out the link below.
One of the things I love most about this design and this style of furniture in general is
the fact that it's made from wood and glue only.
There's no screws or hardware.
In fact this was an important lesson I learned during COVID.
Because of the supply chain issue and the ridiculous back order for hardware it meant
that I had to design pieces that didn't rely so much on other hardware and materials and
allowed me to focus more on the wood itself.
You of course can't always get away with this but this lesson was certainly a valuable insight
into creating more natural designs.
Now you may notice here that I'm back to polyurethane glue and once again this is for two specific
reasons.
One because it has a longer oven time than Titebond original and two because in this
instance I want the glue to foam up unlike earlier when I wanted to wipe away the glue.
You can see the amount of squeeze out and drips here.
The reason why this is an issue is because I'm about to use some carving discs and I'm
concerned the squeeze out from the dried Titebond which is a PVA glue would clog up the glue.
Especially because the discs may generate some heat.
This isn't an issue with polyurethane glue.
So I mentioned earlier that this simple technique is impossible to get right and my explanation
for this may come across a little strange but it's quite obvious that sculpting furniture
is an artistic endeavor and of course art is subjective but a lot of sculpture tends
to represent an identifiable object like an animal or a person.
These are things with features that can be recognized.
They can be measured for the most part.
But sculpting furniture tends to be more abstract.
Other than the basic measurements of height, width and length everything in between is
whatever you want it to be.
Which sounds great.
I mean as makers we all dream of being able to create whatever we want but when it comes
to an abstract sculpture such as this coffee table every carved curve that I'm creating
looks good but I know it can be better.
So I remove a little bit more but I still wonder if it can be improved.
I continue to remove more material always knowing in the back of my mind that it will
get to a point where I've taken too much off and the piece is completely ruined.
I feel like every sculpted piece I've ever made is a balancing act of pushing forward
without screwing it up.
Basically what I'm trying to say here is that I find it impossible to create a perfectly
sculpted piece of furniture as I always wonder can it be better?
I use specific tools when it comes to sculpting the stacked laminations.
I always start with the Arbotech Turbo Plane which allows me to remove the bulk of the
material.
Here is where I'll get my rough shape.
Then I'll go through the different grits of my carbide discs to help smooth out the aggressive
machine marks left by the Turbo Plane.
Now it's very difficult to get a smooth flowing curve when carving with discs because of the
small surface area on the disc.
So what I like to do when smoothing out wide curves is to use a sander with a flat surface
like this belt sander.
The flat area of the belt sander helps to smooth out the large curves and my saw rasp
helps to smooth out the tighter curves that the belt sander won't fit into.
Then of course I use my random orbital sander with a soft pad to help smooth out the entire
surface.
I'll leave some links below if you're interested in any of these tools.
Now unfortunately it was at this point where I began to see the issue of not planning ahead
as earlier I had no idea on how long I needed to make each board which now results in having
to remove a ton of material.
Even though I'm winging it, I do have an image in my head of how I want this piece to turn
out and it consists of a flowing curve that's deeper at one end and thinner at the other.
But that's the only reference I have and now I realize how wasteful this go-with-the-flow
style of building can be.
I'm always very careful with the amount of material I order as I don't like to waste
anything and this amount of waste isn't accessible.
Granted I do have a bunch of offcuts that I'll be able to use for something in the future
but all this sawdust is from grinding away material that could have been saved if I'd
planned ahead.
This is certainly a lesson learned.
I wanted to introduce some extra features so I decided to add a textured detail to the
inside of the coffee table.
This is a technique I've used on other projects and I'll leave some links in the top corner
if you want to check those videos out.
But generally I'll use a gouge chisel to achieve the look that I'm after.
But with such a large end grain surface I thought I'd try creating the texture with
my angle grinder and a carbide disc.
Now to be honest I do prefer the look of the texture from my gouge chisel but let's be
honest I'd probably still be carving if I did it by hand.
Now this is a detail that will most likely go unnoticed.
After all this is a coffee table that sits low to the ground but I've always been a fan
of designing furniture with hidden details.
It's like a well-written song.
You can still discover new notes even after your hundredth listen.
Hopefully this coffee table will continue to surprise people in the years to come.
So now that the top has been glued to the base it's time to transfer the template shape
to the top.
Now this template is only 3mm thick so it's a little concerning to go straight to a large
router with a giant flush cut bit.
So I'm going to transfer the template shape to the table with a small pattern bit, then
I'll run my large router using the tabletop as a guide.
Now you may notice that I'm going the wrong way with my router but that's because the
grain is running in a different direction and Tasmanian Blackwood is notorious for chip
out with routers.
This is called climb cutting and if you're not well experienced with routers then please
do not do this as it is very dangerous.
Originally I was thinking to just chamfer the top edge of the tabletop but after taking
a step back and having a good look at the near finished piece I realized that the top
needed to be rounded over to suit the curves of the table.
The only issue I have with this idea is that I really like the shape of the top and wanted
to keep a hard line around the edge.
You see when you add a round over to an edge you now lose the definition of that edge which
takes away from the overall shape.
This is great in some scenarios but like I said I wanted to keep the shape of the tabletop
so I did both.
By not setting my router to the full radius of this giant round over bit I'm able to have
a round edge that blends in with the rest of the table while also keeping a sharp line
for the shape of the tabletop.
So I'm going to be doing something a little different when finishing this Tasmanian Blackwood.
Oil finishes tend to add an amber colour to wood.
Now this can be very appealing in some woods like walnuts but for me using oil on Blackwood
can look a little intense.
So I'm going to add a white finish from Fitties before applying the oil.
This is a standard process when oiling light woods like white oak as it stops the oak from
going yellow but it's not as common with darker woods primarily because the white pigment
can show up in the grain.
The trick here is to sand the piece perfectly, apply the white and then wipe it off.
Once dried I then apply the hard wax oil as per usual.
The white finish stops the top coat from turning the wood yellow and if done correctly this
method looks incredible on Tasmanian Blackwood.
