Four years ago I started an epic DIY wardrobe build. Today I look back at how good the design was and how well the wardrobe has stood up to wear and tear.
I would be so grateful if you Joined my Channel: DIYte PATRON / charliediyte for exclusive behind the scenes content and access to my Discord chat forum; or
BUY ME A COFFEE https://bit.ly/3xuQ3zb if you fancy buying me a coffee to help me keep making this free content - you can also join my Discord here too, if you don't like Patreon :)
0:00 Introduction 0:43 Patreon Link 1:17 Wardrobe Construction 3:37 The Big Reveal 4:56 Potential Issues 5:09 Doors Bowing 7:00 Wardrobe Ceiling Bowing 7:45 Damp & Mould 8:30 Lighting 9:28 Paint Durability 13:03 Subscribe to Me!
This video provides a four-year retrospective on a professional-grade DIY wardrobe build. The creator evaluates the durability of the materials and hardware used, discusses the success of specific construction techniques, and identifies key mistakes to help others avoid similar pitfalls in their own woodworking projects.
Three years ago I embarked on a wardrobe build. The idea was to build a professional grade wardrobe
with basic tools, with all the cutting and a little bit of constructing done in a pop-up
workshop, because that's generally how I roll. Seven videos followed, watched by more than two
and a half million of you, so I can't thank you enough for that. And links to all those videos
will be in the description below this one. Now Darren got in touch last week to say he'd
overcome his fears of taking on a project like this by watching the videos multiple times and
planning, planning, planning, designing everything on SketchUp. I wish I was using SketchUp. With the
Open Cutlist add-on built in, he finally bit the bullet and has the plinth and three carcasses
constructed. And he's now kindly become a patron and uploaded these images to my Discord channel
where I and everyone else can now support him with the rest of his build. So after reading his
comments I thought actually it'd be quite useful to do an update video, so that if any of you after
watching those videos are planning a build of your own, you can find out how this wardrobe system
has fared over the last three years. So today's video is a quick update to remind you how I built
it, what's worked well, and the improvements, if any, I'd make if I was building it again.
Now you can obviously delve into each video for the details, but let's have a quick run-through
of how I put this together. For a start we had a pine plinth, then moisture-resistant MDF,
five carcasses of 18mm construction with a 12mm back piece. We then have these top boxes
that sit on top of the carcasses obviously, and as you can see here the light wiring was hidden
in channels that ran between these two sections. All the lighting had to be installed before the
top boxes could be fixed in place. And for these wide cupboards, a steel plate strengthening this
front section so that if there's anything heavy in the box above, it's not going to bow down. Also
with all the weight of the clothes hanging. These fascias were cut from, again, planks of pine
with a routed decorative front edge. I think this fascia makes the wardrobe look more professional
and from a practical point of view hides those cut edges of the 80mm MDF carcasses. And each
cupboard has a light activated sensor, which unfortunately Sensio have since discontinued.
And whilst the main cupboards have got the light just running along the inside top edge, which is
also angled backwards. I routed a strip into the underside of the carcass so you can't see the LEDs.
It was following the advice of one of you lot to actually put an additional strip down this
cupboard so that the LEDs illuminated each individual shelf. Cunning, eh? And in fact the
company I bought the lights and sensors from has sadly got bust too. The drawers are a really simple
design that's simply glued and screwed together with these black soft close heavy duty runners
and the black finish I chose so that they literally blend in. I never even noticed
they're there to be honest with you. And the doors, perhaps rather controversially, are this really
simple 12mm back panel with 12mm rails and stiles glued to the front. What I call a faker
shaker design. We'll talk about those a little bit more in a minute. With these blum soft close,
oh a bit of dust there, with these blum soft close hinges. Now I was so exhausted and relieved to finally
get that seven part video series finished. I never did a proper reveal at the end and a few of you
pointed that out. Crazy really if you think about it. So let's start this video with a little summary
of everything we've got here. So as per the original drawings we've got the five wardrobe
units. The two on the outside with full length hanging. The two immediately inside that one for
me. The other on the far right for DIYife with four large drawers and hanging above in each.
And then DIYife has an extra cupboard in the middle with four shelves and four more drawers.
The top boxes above provide additional storage and I'm particularly chuffed with these triangular
corner cupboards which really maximise the space available for storage. The drawers have a massive
full length extension amounting to 450 millimetres past the front of the carcass. I put two dividers
in the top drawer to separate the pants from the socks from the bouts etc. I've taken the pants out
because you don't want to see my pants. And also the unmatching mess of socks in the middle divider.
And I'm so pleased I fitted soft close runners because whilst tricky to install you can't put
value on something you can just push and walk away from. For the same reason I simply love the soft
close doors. A feature you wouldn't get with traditional butt hinges whilst concealed hinges
are so much stronger than butt hinges particularly given the MDF material they're being fixed into.
And if you're wondering what the difference was between soft close and normal hinges here's this
door with the soft close switched off. And if you're a butt hinge fanatic you could only dream
of this sort of adjustment once the doors are hung. So that was a big plan and it all worked
rather well but what I couldn't predict was how durable it was going to be, how well it was going
to age. So let's run through the potential issues that I saw at the time and what has actually
happened in those three years. Now first up when you make doors in this slightly dodgy DIY way I
love making them like this because by making them with a flat back panel rather than having to
indulge in mortise and tenons or buying a, I don't know, Festool domino machine,
you really can keep things very simple and it makes it very accessible for people of all skills
levels. But there is that potential issue of the door bowing. Now and I have had this happen to me
a couple of times in the past when a door that I just finished making bent like a banana. Now
I didn't have this issue here and I did a couple of things to make sure that wouldn't happen.
Firstly by putting packers underneath my workbench I made sure on day one that the workbench was
absolutely flat because the danger making doors like this if you're making them on an uneven
surface when you nail your rails and stiles onto the back plate you're fixing the shape that the
back plate was in when you put them onto it. Secondly in gluing the rails and stiles to that
base piece I made sure that the glue was consistently spread. I don't know whether this
helps but again one of the doors that bowed in the past I made by using a gap filling adhesive
which I just put in wavy lines around the back. Thirdly once all the doors were constructed I
laid them in a big pile in the garage on a completely flat base until I was ready to paint
them. And fourthly this door is well supported it's got four hinges up the back which I think
will help it lock in place. And finally I put door stops at the top and the bottom just in case when
the door was in its shut position if there was a mismatch the door could naturally warp over time.
So all things considered the doors literally haven't moved an iota since I installed them.
I was also quite worried about this wide cupboard bowing down along the top edge because of the
weight partly of the shirts wave you've got hanging in here pulling it down but also the
weight from things bearing down on it from up above. But again there has been absolutely no
evidence of any sagging down of this cupboard and I think that is almost entirely due to the
metal banding that I put along the front because MDF as we all know is pretty unstable even when
you've got two 18 millimeter sheets like I have screwed to each other. I was a bit worried about
the drawer runners giving me problems particularly the soft close element which has a pin that clips
into a sort of guide at the back but I would say that once I set them up and align them correctly
they've worked faultlessly ever since. Now at the time of the original video I had quite a lot of
people saying to me aren't you worried about damp and mold inside the cupboards and my response was
firstly no because I've got quite well insulated walls in here Kingspan K118 and also PIR behind
that but secondly if you've watched any of my recent videos you'll know just how ridiculously
fixated I am with ventilation. Somebody said recently this guy's obsessed with damp and mold
so the relative humidity levels are quite low in here anyway and actually if you look in here
that's the fuse spur for the lighting. An ethernet cable that's currently unconnected. You can see
there isn't a single speck of mold or condensation. The one potentially weak link we've got here is
with those lights. Now on one hand the light strips the led strips themselves can be quite
easily replaced should they fail because the connectors are accessible here in the cupboard.
After all I did actually put the led strips in after everything was installed. The problem we've
got though is with those sensors. Firstly they've been discontinued possibly because of this
ridiculous situation where I had to paint a white spot on the door for the sensor to activate because
it didn't like my paint colour. And secondly even if they hadn't been discontinued and I wanted to
replace them that is going to be very difficult because I pressed them into the cupboard from
below. There isn't any slack on the cable for me to pull them out and replace them which in hindsight
was a mistake because I could easily have made it long enough to pull it out entirely. So I have got
a bit of a problem if I ever have any problems with them. I just hope they are so basic there
isn't much that could possibly fail. And so we come to the final section of this video paint
durability. Now I painted this entire wardrobe system with this Johnston acrylic durable edge
shell and in fact I've used up basically the whole tin. There's a little bit left hopefully
of this 4.6 litres. So that's how much it took to paint all of these wardrobes. And it's worth
pointing out that Johnston's about a year ago brought this out. Aqua Guard Durable in a matte
finish this particular one. They do different sheens and I'm actually going to use this this
afternoon on the new bonkett seating I've been working on. So watch this space to see how we get
on with that. I didn't go oil-based because it would have taken too long to dry particularly
given I was painting most of this back in February 2021 which has made me realise that these
wardrobes are four years old not three. There's my maths coming to play again. But all things
considered it's fared pretty well. We've had the odd scuff where the top boxes had sanked a bit.
You're not really meant to install top boxes with this width to height ratio just because it puts a
bit of strain on the hinges but these are fine because they're blum. And a little bit of adjustment
on those top boxes and they're working beautifully again in readiness for the repainting. Also we've
got this one here where the top box door had clashed with the frame and taken a bit of the
corner off. And finally there are these scuff marks on pretty much every drawer every door where
we've got drawers because accidentally the drawer has the door has sprung back a bit we haven't
realised and we've pulled the drawer open which has smashed the drawer into the door and scuffed
it. My advice to you when you're making these drawers is put a rounded edge, route a rounded
edge on the corner so if this happens which is pretty unavoidable for a design like this,
the drawer is more likely to sort of glance the door away rather than bash straight into it and
scuff the surface. I'm tempted to protect those inner surfaces and also the drawer fronts which
have got sort of fingerprints on them with I don't know a protective varnish like minwax or blockade
or actually sort of rock top not blockade. Maybe let me know in the comments if you've done a
similar thing and how effective it's been. I'm just a bit sceptical because I painted our kitchen
table with something similar and when I did have to come and repaint it I had to scrape off all of
that varnish. So we're really interested to hear from you how you got on with these sort of
protective coatings. But anyway I filled that damaged corner with two-part wood filler and
luckily have, as I said, have a small amount of the acrylic paint left. So a quick run over those
scuffed areas taking care to paint the whole area to prevent the problem of flashing. I did
some spot touch-ups as well but looking at this in the light I reckon the whole front could probably
do with a bit of a repaint to get rid of finger marks and the like which brings again back into
focus that whole idea of putting some sort of a protective finish over the front. Let's have
a discussion about that in the comments. But anyway considering it's just over four years old
I think it's looking pretty good and I promised myself some sort of a shoe rack but I still
haven't got round to making it. So that's it for today. I hope you found that useful. Massive thanks
again for watching. Don't forget details of everything I've talked about including links to
all those seven videos will be in the description below this video and let's carry on those comments
on things like protective finishes and anything else you can think of mentioning. Finally if you're
new to my channel it would literally mean the world to me to have you subscribe. You can do
that by clicking on the link here and don't forget to click the bell notification icon so you get
notified of all my future uploads. Thanks again for watching and I'll see you next week when I
promise you I'll be doing bonkettes!