Ghost MIDI Hexpander Install part 4 "The Controls"

TheGospelGuitarist
1 follower
Mar 29, 2026
Installing the two switches and volume control for the Ghost Midi Hexpander system.
Gospel guitarist here and now we're gonna get to the nitty-gritty the drilling
Marked out where I'm gonna put them and I
double-checked
where they're going and
Make double checking making sure none of the installed wiring is gonna be in the way there
Seems everything is clear
so very carefully
Doesn't take much
thin top
the other one
And that should do it
now what I usually do is
take the
nuts off and
Just kind of stick the switch into the hole
You have to excuse my sniffling nose
And then I see how snug they're gonna go in you know
Making sure that they'll fit
These are a little too tight
So I'm gonna open them up just a little more before I remove the tape
And that should be good
Yep, that'll do it
And as you can see there
There's my two holes
ready for installation of my switches
Okay, and then now I'm going to complete the switch install in this video
And in the book it gives you the color codes
for the two switches
So that when you're up is up and you're down is down on the guitar
for the switch that's
Switching your program up and down
I mean why would you want to pull up if you want the program to go down right so you want to get the switch?
oriented the right way and
For me, it's just yellow is down, so I want the yellow wire
Facing the bottom of the guitar
When I install it so the yellow wire will be
So the yellow wire will be on the bottom
When I install the switch that way when I flip it down
It's gonna mean down, so I'm just gonna feed this through here wire will just be loose the
The boards gonna be mounted in the center of the guitar
Kind of underneath this pickup actually
If there's room, and I won't have to move it so
but to begin with I'm going to go ahead and install the
switch
There's two nuts
For each switch so you can adjust
How much of the switch jack is sticking above?
So that you can adjust them and get them nice and flush
Okay
There we go
Burr from where I had cut off they have these little tabs, and I don't like the tabs
And I don't like these being on the top
Because they don't look as good so I put these on the bottom, and I use these on the outside of the guitar I
Need to file that off, so I'll be right back
Okay
Tighten that up later, so that's one switch
now the next switch is
for the
Switching between the actual MIDI
Switch with a switch towards the red wire. It means the MIDI is being used I
Switch towards the blue wire
It means that whatever this other switch on the guitar is set to
Like if it's set to the acoustic then I'll get the acoustic sound
So the two switches are going to be working together
And when I go in the middle just uses everything
MIDI my acoustic sound
And then if I have this one set in the middle, then I get my MIDI acoustic and electric it sounds all at the same time
Okay, that's a rough install of the switches
they still need to be tightened up and
I'll feed the wires inside
When I'm ready to hook them up well as you can see I've removed the
Magnetic tone control it's inside of the guitar right now
Decide whether I totally desolder it and remove it or just tuck it away
In case I want to revert the guitar back, but I really don't think that's gonna happen so
Now I gotta install the volume control in its place as you can see these are like mini pots
So again small switches and small volume controls
You can squeeze a lot of switches in a small space
This looks a little bit high
So I'm gonna take it back out
And adjust the nut right here so that I can have less thread coming up through the body
Because if you have a lot of threads sticking up then that means the whole knobs gonna be up in the air
I want it as close to the body as possible like to match these
But you don't want to limit yourself too much
Because you need room to get the nut and everything on the washer and the nut so
Wow
Happened easily twice. I
Really thought that was gonna be a problem
always use your
closed end
Wrench which gets a little dicey, but that'll complete the install
for
volume control of the MIDI system
Back on try to get the number 10 lined up with the arrow and it worked just fine
so
So far, that's what I have in the build
Looks good so far now for the hard part
Got to put the switch in or the 13 pin jack in stay tuned
