Most Common Mirror Installation Mistakes

Auto Retech
2 followers
AI Generated·May contain errors
In this video, we're going over some common mistakes that you can do installing mirrors.
We're going to break this down into four different categories, wiring, seals, fasteners,
and the glass. If you're replacing a mirror assembly and not just the glass,
you have a wiring harness coming out of the mirror assembly. It doesn't connect right there.
For the most part, on all vehicles, you're going to have to remove the door panel.
Before you even take the mirror apart, it's a good idea to check your connectors and make
sure they line up with your old ones. If they don't line up, don't even replace it.
Don't try to cheat and not take the door panel off. If you have that wiring harness there,
don't come over here and just try to cut these wires when you put the new mirror on
and try to splice in the new wires. You're just going to end up with a headache.
When you have the door panel off, take a look at the wiring harness. It goes behind the vapor
barrier. Keep that in mind. If there's any fasteners, you want to make sure you
re-secure the wiring harness exactly the way it was when you took it off. This one has some wire
ties in some certain areas. If there was fasteners there and your new mirror doesn't have fasteners,
you can always use wire ties. When you have your new mirror, you want to make sure you send the
wiring harness through the same way that it came out. Then also make sure all the wires pulled out
of the mirror itself. If there's a little too much slack in there, it might get wrapped around
the wrong way or you could get it wrapped around a stud. When you go to tighten it down, you're
going to squish the wires. When you're putting this back together, it's important to have that
wiring harness in that same location. You don't want it around any moving components. Let's say
you wrap the wire around this way and went down right there. Then if you went to put the window
up and it was wired wrong, you're going to pinch the wire. You can eventually break the wire or
your window is not going to go all the way up. Even when those wires are routed wrong and it's
tightened down, you can't even tell that it's installed wrong. Don't forget to connect the
wires or you're going to be pulling your door panel apart afterwards. Make sure you plug them
in to the right locations. Most mirrors have a gasket or a seal to keep out the elements.
If the gasket stays with the vehicle when you go to put the new mirror on, if it has a gasket,
you don't want to double gasket it. Or if you don't have a gasket at all, even on the new mirror,
you're going to end up with water getting into the vehicle. Don't forget if you have extra
insulation that's supposed to go in here, make sure you put that back. If anything,
you probably just get a little extra wind noise or a draft when it's cold.
Now let's talk about fasteners. The nuts or bolts that actually hold the mirror on. Now,
when you're taking the mirror apart, make sure you support the mirror when you're taking the last
fastener out. This has a nut right here. Pull that last nut out and I'm supporting the mirror.
Otherwise, the mirror could just fall. When you get a new mirror, there may already be nuts
on here. You want to take those off. Otherwise, the mirror's not going to fit on properly.
And some mirrors have a type of retainer that's going to hold the mirror a little bit so that it
doesn't fall. Don't forget to put the nuts on or the bolts. Some people forget to tighten the
bolts down or nuts down and then the mirror's going to be extremely loose. You're going to
notice right away when you're going over bumps. You definitely don't want to over tighten it or
you're going to strip something out or break something. Now we're going to talk about mirror
glass. If you just wanted to replace the glass and not the whole assembly. Sometimes it's going
to be a lot cheaper for you just to do that, but sometimes it's extremely tricky. A good tip for
when you're taking the glass off, whether it's cracked or anything, take some masking tape
and put it over the glass. You can coat this whole thing in masking tape.
Then if you break the glass any more than it's already broken,
it probably won't get or probably will not harm you. Then also it's a lot easier to clean it up.
Nothing was going to spill on the ground or anything. Make sure you wear safety glasses
just in case. Now these all come off different. Sometimes they pry off just like that using a
screwdriver or sometimes they actually slide up with the connectors. You always want to be careful.
You don't want to ruin the terminal, so just lightly pry those up. Keep in mind where the
wires went. If the orange one was on top, make sure you put that one on the top. Don't switch
them. If you're unsure of how you remove it, take a look at the back of the new one.
This one has clips on it, so this is where you would want to pry in between here. Either get
a pick or a screwdriver and just try to pry around here. Whereas something like this one,
this one actually has little fingers that go in here that the mirror would actually slide up.
When you're going to install the new mirror, take a look at the back. There should be some tabs
like this, depending on the type of mirror it is. Those tabs are going to sit on the outside
of this bar right here. This happens to be a GM mirror. Some other vehicles may be a little bit
different, but pay attention to little things like that. You could do the same with the tape
on the new mirror if you choose. If you don't want to break it, it's not necessary. Then just
wherever the clips were, that's where you want to push on the mirror. Find the center of the mirror
and just give it a good push. Make sure you push on the center of the glass like that until it
locks down. Do not push like this. Some important things to know is if you have power folding
mirrors, don't just fold them in manually. When you fold them back, they're probably going to be
loose and the best thing to do is just cycle them through. If you do it by accident once or twice,
it's probably not a big deal, but you don't want to be doing it that much. Then if you have mirrors
that have motors where the mirrors move, you don't want to do this too much. Don't do this.
Don't glue your mirror on. Then in the future, no one's going to be able to get it off or get
it off very easily. I've also seen people using duct tape or sheet metal screws. Don't do any of
that. There's our mirror install mistakes. If there's anything that you think I missed or you
have a story of something that you messed up, leave me a comment below. If you enjoyed this
video or it helped you out, make sure you subscribe to our channel, ring the bell,
turn on all notifications so you don't miss any of our videos.
