PG Diploma in Piping Design Engineering: Complete Guide (Full Course 2026)

Welcome to this course. This course is designed to provide you entry-level knowledge of Piping Designing. You can find even more syllabus, is covered in this course than the standard PG Diploma in Piping Design Engineering. And if compare the cost, it cost you nothing as compared to a standard course.

This Course is a perfect combination of theoretical study as well as practical work. You will Learn the use of your knowledge in practical work by some examples of exercises. Module 7 is coming soon.

🎬 TIMESTAMPS
SECTION 0: COURSE INTRODUCTION
0:00:00 - Introduction
0:01:37 - Course Syllabus
0:07:02 - 0.0 Module Introduction

SECTION 1: PIPING FUNDAMENTALS & COMPONENTS
0:08:09 - 1.1 Piping System
0:10:13 - 1.2 Plants Type-1
0:15:35 - 1.2 Plants Type-2
0:20:04 - 1.2 Plants Type-3
0:22:14 - 1.2 Plants Type-4
0:25:44 - 1.2 Plants Type-5
0:29:25 - 1.3 Plant Designing Type
0:31:36 - 1.4 Phases of Plant Designing
0:36:51 - 1.5 Types of Design Companies
0:39:40 - 1.6 Knowledge Requirement
0:46:10 - 1.7 Piping & Other Departments
0:51:26 - 1.8 Codes and Standards
0:57:05 - 1.9 Piping Components
0:58:08 - 1.10 Pipe
1:00:09 - 1.11 Pipe Designation
1:07:02 - 1.12 Pipe Manufacturing
1:14:08 - 1.13 Pipe Fittings-1
1:16:37 - 1.13 Pipe Fittings-2
1:19:08 - 1.13 Pipe Fittings-3
1:22:44 - 1.14 Pipe Flanges-1
1:25:57 - 1.14 Pipe Flanges-2
1:29:26 - 1.13 Pipe Fittings-4
1:33:56 - 1.14 Pipe Flanges-3
1:36:28 - 1.15 Flange Gaskets
1:39:59 - 1.16 Valves
1:41:25 - 1.17 Valves Types-1
1:50:34 - 1.17 Valves Types-2

SECTION 2: EQUIPMENT TYPES
1:57:28 - Module Intro
1:58:18 - 0.0 Equipments
1:59:21 - 1.1 Static Equipment
2:00:13 - 1.2 Tanks
2:06:52 - 1.3 Heat Exchangers
2:11:38 - 1.4 Heater & Boilers-1
2:14:26 - 1.4 Heater & Boilers-2
2:19:22 - 1.5 Columns
2:21:51 - 1.6 Reactors
2:23:40 - 1.7 Separators
2:27:28 - 1.8 Strainers
2:28:47 - 1.9 Air Vents
2:31:26 - 1.10 PIG Launchers
2:34:35 - 2.1 Rotary Equipments
2:35:18 - 2.2 Pumps
2:40:04 - 2.3 Compressor
2:43:55 - 2.4 Agitator
2:47:24 - 2.5 Turbines
2:49:23 - 2.6 Turbo Expanders
2:50:40 - 2.7 Engines
2:54:28 - 2.8 Fans & Blowers

SECTION 3: PROCESS DESIGN & DOCUMENTATION
2:58:38 - 0.0 Module Intro
2:59:60 - 1.1 Project Documentation
3:02:45 - 1.2 Chemical Process Selection
3:09:15 - 1.3 Anatomy of a Chemical Process
3:14:19 - 1.4 Material Balance
3:18:56 - 1.5 Energy Balance
3:24:37 - 2.1 Plot Planning
3:34:15 - 2.2 Equipment Layout
3:40:15 - 3.1 Symbols
3:51:46 - 3.2 PFD & UFD
3:54:52 - 3.3 P&ID Exercise-1 (Tank)
3:58:50 - 3.4 P&ID Exercise-2 (Heat Exchanger)
4:03:14 - 3.5 P&ID Exercise-3 (Separator)
4:07:05 - 3.6 P&ID Exercise-4 (Column)
4:14:58 - 3.7 P&ID Exercise-5 (Complex)
4:26:18 - 4.0 Section Intro (GA, ISO DWG, Linelist)
4:28:02 - 4.1 GA DWG Ex-1 (Part-1)
4:36:25 - 4.1 GA DWG Ex-1 (Part-2)
5:09:25 - 4.1 ISO DWG Ex-1
5:26:14 - 4.1 Line-List

SECTION 4: FLUID MECHANICS & CALCULATIONS
5:29:23 - 0.0 Module Intro
5:30:26 - 1.1 Fluid & Its Properties
5:37:02 - 1.2 Types of Fluids
5:40:06 - 1.3 Fluid at Rest
5:42:43 - 1.4 Fluid in Motion
5:45:32 - 1.5 Continuity Equation
5:51:04 - 1.6 Bernoulli's Theorem-1
5:55:18 - 1.6 Bernoulli's Theorem-2
5:59:13 - 1.7 Pipe Size Calculation
6:07:49 - 1.8 Pipe Thickness Calculation
6:12:55 - 1.9 Pump Selection
6:18:39 - 1.10 Insulation Thickness Calculation
6:24:00 - 1.11 Mitre Bend Calculation
6:30:27 - 1.12 Dyke Wall Calculations

SECTION 5: FABRICATION & SUPPORTS
6:35:50 - 0.0 Module Intro
6:37:34 - 1.1 Fabrication Activities
6:40:58 - 1.2 Types of Welding
6:45:46 - 1.3 Piping Lining
6:51:33 - 1.4 Piping Insulation
6:56:42 - 2.1 Supports Introduction
6:58:02 - 2.2 Types of supports
7:00:43 - 2.3 Hanger Supports
7:05:59 - 2.4 Clamp Supports
7:10:41 - 2.5 Strap Supports
7:14:46 - 2.6 Saddle Supports
7:18:59 - 2.7 Slide Supports

SECTION 6: STRESS ANALYSIS & TESTING
7:21:18 - 0.0 Module Introduction
7:22:49 - 1.1 Types of Stresses
7:26:23 - 1.2 Static Loads
7:30:28 - 1.3 Dynamic Loads
7:35:56 - 2.1 Visual Inspection
7:38:18 - 2.2 Liquid Penetration Test
7:40:27 - 2.3 Magnetic Particle Test
7:44:41 - 2.4 Radiographic Testing
7:48:15 - 2.5 Ultra-Sonic Testing
7:49:48 - 2.6 Hydrostatic Pressure Testing
7:52:29 - 2.7 Pneumatic Pressure Testing
7:55:37 - End of Course