Building a Budget DIY Container Shop (Full Build)

Design Ideas
29 followers
In this video we build a budget minded workshop from two 40' shipping containers, a set of used trusses, and lumber we milled ourselves for less than $15,000.
#diyhome
Courtney and I love building things
with shipping containers.
From our shipping container home that we lived in
to our buried off-grid power system,
we love them for their portability
and instant weather-tight storage.
So when we set off to build
our budget-minded equipment storage shed,
I knew I wanted to incorporate containers into the design.
With a set of secondhand roof trusses,
used shipping containers,
and lumber that we milled ourselves,
I'm hoping to be into this project for less than $15,000.
Step one was to prep the building site.
Our property is steep and rocky,
so I had my work cut out for me.
After roughing in the pad
with a massive 30-ton excavator we rented over the summer,
it was time to get things level and flat.
I was able to get a bunch of fill dirt from behind our shop
while simultaneously digging our shallow well.
Go check that video out
when you're done watching this one.
As usual, our army dump truck was the star of the show,
and I moved literal tons of dirt to get things level.
It was really neat getting to use the water
from our new shallow well to help with compaction.
I used the vibratory roller on the skids here
to get things nice and flat,
and then it was finally time to take delivery
of our first shipping container.
With how difficult it was in the past
to get a 20-foot container delivered,
I was pretty worried about what it was going to be like
to get this 40-foot high cube up here.
But our massive road project from the summer paid off,
and he was able to drive it all the way to our house.
I cannot believe that we just got
a 40-foot container up to our house.
The delivery driver backed it most of the way down the hill,
and then it was up to Courtney and I
to get it the rest of the way there.
We were able to use the skids here
and the excavator to drag it into place.
Then we took delivery of the second container
and drug it into place as well.
That's when this project really started to feel real,
and it was the motivation that I needed
to double down and get this thing cranking.
Once the containers were perfectly leveled and spaced,
I welded some rebar in between to help hold them in place.
I wanted to add some natural light to the containers,
so I decided to add some windows.
I started welding up metal window frames
made out of square tubing.
The windows will then slide into these frames.
Once the window frames were done,
it was time to cut the openings into the containers.
I used an angle grinder, measured twice,
and I hoped that I only needed to cut once.
My plan totally worked, that was awesome.
On our shipping container house,
I fully welded the window frames, but that took forever.
So on this project, I decided to just stitch weld
around the perimeter.
In hindsight, this was a mistake
because we did end up with a few small leaks.
I sprayed the frames with a bare metal primer
and then caulked the perimeter to seal the gap
between the frame and the container.
Then I pressure washed the containers to prep them for paint.
And once it was dry, it was time to install the windows.
I caulked the perimeter and inserted the windows
from the inside.
To save money, we used in stock new construction windows
from our local hardware store.
This isn't how windows are typically installed,
but it means that I didn't have to add any additional trim
on the outside to cover the window flange.
The downside is that we're relying on a caulk joint now
for waterproofing, so again, not ideal for a home,
but for a workshop, it should be fine.
And man, does it look good.
Then I called Courtney in for help to paint the containers.
We decided to try painting the window frames
to help make things look a little more custom.
She started by taping off the glass on the windows.
Then she sprayed a special vinyl primer on the frames
to help prep the windows for paint.
We're using a water-based, direct to metal exterior paint
intended for metal surfaces in the color suitable brown.
In the past, we've had good luck spraying this paint
through an airless sprayer,
and so that's what we decided to do again.
It's pretty crazy how quickly this process happens.
You just drop the pickup in a can of paint
and start spraying.
Faster than I can keep up with Courtney,
she sprays the paint on the containers,
and before we know it, we're done.
These containers weren't perfect,
but we did ask for ones with minimal dents and working doors.
This was important to us because painting them
will showcase every single dent and blemish.
Spraying the windows actually went really well.
Courtney was careful to not spray too thick of a coat
to try to avoid runs.
Six gallons of paint later, and what a transformation.
The results were incredible,
and we now had two matching containers.
Painting the windows seems like it was a success,
and it looks so awesome to have them color matched
to the building rather than white.
Next up, it was time to finally get started
on the roof structure.
We ended up with one extra roof truss,
so I thought it would be cool
to add a front overhang section.
This is gonna prevent the snow from piling up
in front of the container doors
and give us a little more covered parking space.
I headed back up to the shop and got to work
making some metal brackets to support that overhang.
Then I welded those brackets directly to the container roof.
During our milling project, we had a few large trees
that made some beautiful beams,
and it's so rewarding to be putting those to good use.
Courtney hoisted them up into place,
and I was relieved to see
that they actually fit in my brackets.
I threw both of the beams to the brackets
and sucked everything tight.
Then we got to do the really satisfying task
of removing the plastic from the windows,
and wow, did it turn out great.
We'll see how well they hold up in the long term,
but it was a really inexpensive way
to make the workshop look a little more custom.
If this project wasn't already a little unconventional,
things really take a turn here.
I wanted to space the center roof structure up
to get a little taller clear span inside of the building.
That meant building a small pony wall
that the trusses will sit on top of to raise them up.
I built the wall in smaller sections
to make things more manageable.
As I studied section up,
I through-bolted it into the container roof.
I didn't have washers,
so I had to go back and add those later.
The second section of the pony wall
got bolted to our roof beam extensions,
and the first half of our framing was done.
Once we had the second container pony wall built,
it was time to start setting trusses.
Whoa!
We've only hung trusses one other time in our lives,
and we were a little nervous.
It feels like there's a lot that can go wrong.
But with Courtney in the excavator and me on ground duty,
we got to work hoisting the first truss into place.
I used a rope to help guide and steer it
while Courtney swung it around.
On that pony wall we built, I used a double stud design,
but I left one stud taller than the other.
That leaves a ledge for the truss to sit on
and a taller stud to attach the heel of the truss to.
It's sort of like a modified post frame style.
That meant that Courtney could set each truss down,
and I could quickly attach it to the pony wall
to secure it into place.
After setting four of the trusses,
I decided that it was time to square everything off
and brace it before placing any more.
And so I built a questionable work platform
for the skid steer and put all of my trusses
into Courtney to shuttle me around.
It's a good thing that she's a great equipment operator.
I added the first roof purlin
and attached each truss to it at the proper spacing.
Then I worked my way down and added a few more purlins.
That locked the top of the trusses in at the right spacing,
but the bottom still had a twist going on,
so we added a rat run.
The rat run then locked the bottom of the trusses
into the proper spacing.
At this point, things were looking better,
but the whole section was not square or plumb.
I used ratchet straps to pull everything into place
and then added diagonal bracing to lock it down.
Then we got to work setting the next set of trusses.
At this point, we had the hang of things
and we really started cruising.
It was such a fun transformation
seeing the roof come to life.
The last two trusses were more difficult to attach
because I didn't have that pony wall stud sticking up.
Courtney held the truss steady,
and I added a couple of roof purlins
from the previously attached truss
to hold the new truss into place.
And before we knew it, we had 12 trusses set and secured.
It was really starting to look like a building,
but at this point, I was starting to feel like
we might lose the race to beat winter,
so we called in some reinforcements to help with the roof.
We added fascia and some stained cedar boards
to the front truss to dress things up
and make the entire building look a lot more finished.
At this point, it was time to conquer my fear of heights
and start putting the metal roof on.
We used the skid steer to get things as close as possible
and try to minimize the number of times
we have to go up and down the ladders.
I harnessed up and headed onto the roof.
I squared off my leading edge
and started screwing down the first sheet of metal.
Working one section at a time,
we would square off the sheet,
then mark each hole before attaching it
with self-tapping screws.
I personally don't like pre-drilling the stack of metal.
It does save time,
but I find that as we slide each sheet off,
the metal from drilling the holes scratches the sheet below.
And to my surprise,
even though we're on a 5'12 pitch roof,
a level actually works great
to make a straight line to mark the screw holes.
And then a discovery.
It turns out that I actually squared off our first sheet
to a fascia board that wasn't square.
Whoops.
And that meant that we had to cheat each sheet down
a little bit to get things back straight.
Having the containers to walk on
are like permanent scaffolding,
and it made this entire process so much easier and safer.
Then we ran out of a container to stand on,
so it was up to me to get the last two sheets up.
We ripped the last sheet width-wise with metal shears.
The exposed edge doesn't need to be perfect
because it will get covered with gable cap.
Now we really had a system down,
and the second half of the roof metal went up
in just a few hours.
I couldn't believe that in one day
we went from rough framing to a functional covered space.
The original plan was to add secondary roof structures
over both of the containers.
But then in the middle of the night,
I woke up realizing that we needed a roof deck.
With the aid team around for a few more days,
we got to work framing out our rooftop deck.
During our lumber milling project,
we mostly made two by six boards,
but some of the larger trees were turned into two by eights,
and these would make perfect floor joists for the deck.
I attached a toe plate directly to the roof container
with screws and adhesive.
On the opposite side, we attached a ledger board
to the pony wall that holds up the main roof.
This gave us a really convenient way
to attach deck joists to the container.
I like to use screws for construction projects like this.
These are structural framing screws
that are rated for this application.
Screwing every deck board down took a long time,
but I think it was worth it to lock everything down solid.
It was so satisfying to watch the deck boards
go down on our rooftop deck.
These deck boards were a waste material
during our lumber milling project
that we decided to turn into random length
and width one by boards.
Perfect for a DIY deck.
To add some dimension and to make the best use
of some longer two by eights that I had,
I decided to cantilever out the center section of the deck.
I also ran the boards at a diagonal.
This just gave it some more dimension and character
because after all, this is a fun project.
On the diagonal section, I was struggling
to cut the boards to the right length.
Then I realized that I could just leave the boards long.
I drew a straight line and I cut them all at once
with the miter saw.
Courtney was able to help me on the last section,
and before we knew it, our deck was done.
I've got some big plans for this deck
that include a bridge, mountain bike jumps,
and maybe even a train?
With the deck done, it was time to do the last roof section.
I really wanted to use up our milled lumber,
but that meant getting a little creative with the framing.
I laminated two by sixes,
cutted our 312 roof pitch onto the pony wall
to create a vertical load path for our rafters to sit on.
Ideally, the rafters would have been two by eights,
but since I used all of those up on the deck,
I made mini roof trusses out of two by sixes,
and they should be plenty for our snow load requirements.
While I worked on the roof purlins and fascia,
Courtney put the last row of screws
onto our upper roof metal.
We definitely should have stained the fascia
before putting it up,
but I was way too excited to stop working,
and Courtney had to pay the price for that one.
Thanks, Courtney.
Before I covered up my convenient scaffolding,
also known as the container roof,
I had to stop procrastinating
and finish the metal trim on the main roof structure.
Equipped with dry shoes and all the courage I could muster,
I headed up onto the roof for hopefully the last time.
After screwing in my fall protection,
I got to work installing the gable trim.
The metal trim gets expensive fast on a building like this,
so we were really trying to optimize cost
versus finished look.
I think the gable trim really finished out
the front of the building
and made things look a lot more polished.
The last step on the main roof was a ridge cap.
That went on without any hassle
and, man, things were looking really good up here.
Reflecting on my design and the use of the scissor trusses,
I was concerned about the possibility
of the containers moving outward
and splitting the trusses apart.
I decided to add a metal cross brace
to the back of the building to prevent this from happening,
and I was feeling much better about my design.
The only thing left to do at this point
was the metal on the secondary roof.
After a few hairy moments of getting the metal up there,
it was time to lay out the sheets.
We've heard some contradicting advice
about whether the roofing screws
should be on the peak or on the flat.
Our metal manufacturer specifies
that screws should be on the flat.
It's the only way to ensure
that the screw is installed tight,
and with the neoprene washer under the screw head,
there are no concerns with leaks.
I'm really glad that we went with two roof pitches
instead of one large one.
It meant a taller clear span in the center.
It made the shorter roof metal pieces
way easier to work with.
It gave us that permanent scaffolding
over the top of the containers when we did the tall roof,
and I think that the taller roof
stepping down onto the shorter one looks really nice.
With the cherry on top,
it was officially time to call this building done.
One month and $15,000 later,
we had ourselves a 1,760 square foot
covered equipment storage shed
that would keep everything we own
out of the weather this winter.
I am thrilled at how this turned out,
and I can't wait to transform the inside of the containers
into my O8.
That's a secret for now.
Thanks for watching, and I'll see you next time.
