Kids DIY Shield Kit Tutorial Featuring a Special Guest!

Shield of Antiquity
8 followers
2 Video Views·Mar 14, 2026
AI Generated·May contain errors
Oh, hey Virtuals friends. Welcome to the workshop. If you're here visiting today, it probably means
you have one of these, and so do I. Hey, I have a great idea. Let's build this together,
and I can show you how it's done. Come on. All right, let's get to the fun part first,
and that is designing and painting our shield. But before we do, let's talk a little bit about
how Vikings painted their shields. Now, Viking Age shields used very simple designs,
like the ones here, for example. In fact, some Viking shields were painted just a single color,
like the ones that were found at Gokstad. They were painted either black or yellow.
Speaking of colors, Vikings used simple colors, and thanks to researchers, you can see what those
colors are on this chart right here. So you can paint a simple design using those colors,
and you'll have a pretty historically accurate Viking shield. But this is your shield,
so you can paint it as wild or as cool as you want. Now, speaking of painting our shields as
we're talking about it, let's talk about how to actually paint our shields. You'll notice on your
shield there is a wood side, and there's a white side. We are going to paint the white side of the
shield. Now, you can use whatever paints you want. I am using simple acrylic paints. You'll want to
make sure that your design stays towards the middle of the shield. You notice you have an
outer ring of holes and an inner ring of holes, and this is where our leather edge is going to go
and our shield boss. The shield boss is that black dome that you should have with your kit,
and it'll go right in the middle. If you paint your design too close to the edges, it could get
covered up by that boss or by that leather edge. So we want to kind of just keep it towards the
center of our ring. Now, one last thing, and that is on your Viking shield, on the back of it,
one of the holes should have a letter, and that letter shows you where the top of the shield is.
So when you're painting your design, make sure that the top of your design lines up with that
letter that's on the back, so that when you're holding it, you're holding the top of your design
upward. All right, that was a lot of information about paints, so let's get to painting.
Time out. You want a pro tip? Would you like to make nice, clean, straight lines on your shield?
You could do that by using masking tape once some of your paint has dried,
and you can just simply put it across your shield, and you'll get nice, even,
straight lines. All right, let's get back to painting. Our shields are painted. Let's give
them a little time to dry. Are we all dry? Let's find out. Yeah, excellent. All right,
next, we're going to put on our leather rim. Now, Viking Age shields, real ones, had a rawhide edge
that held the shield together. It reinforced the shield. It kept splinters from flying off when
the shield was struck by things like swords and spears and axes, and just like a real Viking Age
shield, we are going to sew our leather rim onto the shield. So, what you'll need is your
leather rim. That's that piece with the little holes in it. You'll need your sinew with your
little needle, and you'll need a pair of scissors, and the first thing we're going to do is unravel
the sinew. So, you'll just unhook it, and you'll start to unravel it. Now, we gave you a lot of
sinew, so you have plenty of string to work with. So, this may take a while. Two hours later.
All right, now that we have it unraveled, we're going to thread our needle. Simply just put the
sinew into the little hole in your needle. Now, after you've done this, we're going to pull the
needle to the middle of the string, and we're going to want to have two equal sides. You may
need an adult to help you with it. I may need an adult to help me with it. Let's find out.
Oh, pretty close. I need to bring this one out more. Make sure you don't get yourself knotted up.
We want two equal sides. Ah, I got pretty close there. All right, when you have two equal sides
on either side, we are going to just take these two loose ends, and we're going to tie them
together. We're gonna make a knot. So, loop them, pass them through, just like you're gonna start
tying a shoe, and like so. Now, I like to do this a couple times. I like to do this two or three times
so I get a nice big knot, and the reason we're going to do that is so that the knot doesn't
pass through the holes as we sew the shield together. I'm gonna do it three times. I think
these holes seem like they're kind of big, just like... All right, now, you can start sewing
on any part of the shield, but we want to do two things. One, we will start from the back of the
shield, the wood side of the shield, and the reason we do that is so that when we pull through, that
knot, that kind of ugly knot, is going to be on the back side shield, not on the front where
everybody can see it. It'll only be on the back, and when we go to do this, we're going to put this over.
Like I said, you can start anywhere, but most importantly, we're not going to work on the
first set of holes. We're going to pass through the second set, and the reason we're going to
pass through the second set of holes is, eventually, this is going to overlap itself, and so
we're going to want to connect those two pieces together. So, start anywhere on the shield, second
set of holes, and through the back, we're going to put our needle through, find a hole, pass it through,
and pass it through the other side here, just like that. Pull it through, and you're going to pull
all the way through until we get to that knot, and ta-da! You can see the knot back there, and like
I said, that ugly knot is now on the back side of the shield. Now that we've come through, now we're
going to go through the front of the shield. Next hole, so the next hole in the leather, the next hole
in the shield, through the front, and just like we did before, we're going to pull through, and what we
should have is this bit of string, just like this. So, we went through the front, that means now we
got to go through the back. So, we go back and forth, back and forth, through the leather, through the next
hole, every time, through the next hole. Pulling through, all right, went through the back, we'll go
through the front, and pull it all the way through. All right, so we're going to go back and forth, or front to back,
front to back, front to back, and just going to the next hole over, and we're going to do that until we get
to the last hole. So, I'll catch up with you in just a moment. All right, we're on last hole, and we're
back where we started. Now, remember I said we're going to overlap these, so whether you're on the front or
back, you're going to go the direction that you last went, and we'll go through the hole of the first leather,
through the hole of the second leather, through the last hole, through the hole of the first leather,
on the other side, through the hole of the new leather, on the other side, and let's pull it tight,
like so. All right, now we have this little flap here that's left over. We don't need this, so what
we can do is just cut that off, and our shield is half sewn. Now, you notice that the strings here
are only sewn every other set of holes. We want to fill those in, so to do that, we are now going to do
exactly what we've been doing, but going the other direction. So, I came through the front.
I'm going to go through the back, but now instead of going to the next hole, I'm going to go
back to the last hole I did, this hole. I'm going to needle through like that. I'm going to pull through,
and now look. Oh, not yet. Next hole, but remember going backwards through, and notice, remember we
have this gap here between the stitches we made, but because we're going back the opposite direction,
that's going to fill in. So, just like we did before, one more time, going back the way we came,
going backwards, and filling in the gaps of our string. All right, let's keep going.
Now, when you've come all the way back around, you may notice on the back side of your shield,
there is a gap left over. So, all we're going to do is go back one last time the direction we came from.
So, back through the way we came, now going the opposite direction that we've been coming,
pull it through, and we're going to fill in that gap, just like so. But now, uh-oh, strings on the front.
We don't want to put the knot on the front, remember? So, we're going to come back through. This is the last
one we're going to do. Back through, getting tangled here. I'll make a knot, and one last time.
Now, our shield is completely sewn all along the front, and completely sewn all along the back.
Now, with this little bit extra string we have, what we're going to do is we're going to slip it through
one of these, uh, stitches we've made. So, we have a loop. Hold that loop, bring the needle through,
and pull tight. We are going to clip the, we're going to clip the needle off, set that aside,
and take your string and make a couple knots, just like so. Just like you're about to tie your shoes.
Now, I like to do two or three. We'll go ahead and do three, so we have extra
reinforcement there, and we're going to cut off these tails. We're going to leave a little bit
of, uh, just a little tail behind, but we're going to cut off all this excess.
That's all gone, and you should have something on the back that looks like this.
And dude, that is pretty cool. So, let's get finishing this, and what you'll need to finish
this is your shield boss, your handle. You should have two long screws and two short screws,
and four of these little nuts, these little black nuts that are going to go on the back of your
shield. So, what is a shield boss? This black domed piece. Well, viking shields are held,
real viking shields were held by a single handle that sat on the back, and to make room for the
hand, a central hole would have to be cut. Now, obviously, this kind of leaves your hand exposed,
and lets somebody come in and hit you, hit you in the hand with a sword or a spear or something.
So, they had a, an iron dome that sat on the center of the shield that would protect the hand.
So, to put on our boss, and put on our handle, uh, we are going to screw it all together.
A real viking shield is riveted together. That means a bit of, uh, metal bowl or nail
goes through the front, and then the metal is pounded until it, uh, uh, rivets the whole
shield together. So, on the back of your shield, remember that letter? Well, that's really important
because on the back of your handle is a letter, and those two letters match up. So, we're going
to put the letter to the letter. We're going to take one of our long screws, put it through our
boss, put it through the top of our, uh, shield here, and you may have to kind of push it in. You
may have to kind of twist it in, like I'm having to do right now. There it is. Push through just
like that. We'll do, we'll start with the letter hole. So, the screw goes through the boss,
through the front of the shield, right where the letter hole is, and we're going to use the
hole on the handle that has the letter, matching the letter pieces together. Now, we're going to
want one of these nuts. Now, something I don't have with me is a screwdriver, which is part
of what you'll need. So, let's grab a screwdriver. Perfect. And you may want to have an adult help
you with this. So, you're going to put your screwdriver into your screw, and that's going
to hold it in place. And using your fingers, you're going to twist the nut onto the screw.
It may take you a second to get it.
And we've got it. All right. Perfect. And we're going to do the same thing
on the bottom. Find the holes, and get it all together here. You may have to twist it on. You
may have to screw it on if need be. There it is. Push that right through. And just like we did for
the top, we're going to twist on that nut. Use a screwdriver to hold it in place. And these little
nuts are small for my big old hands. Now, you can hold the nut in place with your hand, and then
screw that screwdriver so it goes all the way through. I'm going to hold that nut in place.
All right. Now, like I said, if you have a pair of pliers at home, you can grab the nut with a pair of pliers
and really twist it on there so it's nice and sturdy. Let's get up close and look at what I'm
doing as we do the other two sides of the boss. We're going to use our small screws for that,
but it's going to be the same technique for all the holes. So, here is a close-up of what
we're doing. Here's our hole, and we have our screw. We're just going to put that screw
right through the hole. Now, you may need to twist it in. You may be able to push it in,
but you might have to twist it in too, and that's okay. Just like so. All right. Let's look at the
back side. We can see the screw sticking through the back side, and we have our little piece here,
and that is going to thread right onto the screw bit. Take your screwdriver,
and you're going to hold the screw or hold the nut and screw that all together. Make sure it's
nice and tight, holding that nut in place and screwing the screw into it. You can also take a
set of pliers and hold that nut in place as you screw with the screwdriver. Let's do it one more
time.
And done. Now, when your shield's finished, make sure to give it a shake and make sure that it
doesn't rattle. If it does, it means one of the screws is kind of loose, and so you'll want to
find which one and tighten it up so that it's nice and tight. And we are done. What a cool shield.
You are ready for your next quest. Before you go, if you have an adult, send a photo of your finished
shield to our email address right here. We will feature your shield on our Facebook page, as well
as react to it right here on our YouTube channel. Thank you so much for building with me today. I had
a blast, and I hope you did too. Hold up. I have one more surprise for you. Our good friend, Jerry
Burke, who runs the Swordsmanship Museum and Academy, is going to teach you a little bit about
Viking Age combat and Viking Age shields. So, I'm going to turn it over to Jerry. Hey gang, Jerry from
the Swordsmanship Museum and Academy here, making this video for our friends at Birch House Woodcrafts.
Birch House has made so many high quality shields and replicas for us, including two phenomenally
made replica archaeological finds of Viking shields. And the amount of effort and detail
that they have put into the construction of these shields is mind-blowing. And so, because of that,
I wanted to put together a little video describing how we use archaeological research
in order to recreate Viking Age combat. This shield, by the way, is a replica of one of the
shield finds, but I will be using our original and my favorite Littrenborg shield recreation.
Now, we don't use these ones for combat, but Birch House has made sure that they are robust enough
in order to survive the combat that both modern-day Vikings and historical raiders
would be going through. So, just like what we have done with Birch House in order to read
archaeological papers and analyze the statistics and specifications given to us by historians and
archaeologists in order to best recreate the shield according to the surviving archaeological
finds, we use surviving depictions of Viking Age combat supplemented by archaeological finds
and descriptions in order to best recreate Viking Age combat. Now, I want to confirm,
there's a million different Viking combat groups and styles out there. Viking reenactment combat,
fighters within the SCA, there's Western martial art fighters that try to use the shape and size
of Viking weapons to recreate a practical martial arts system. All of these are phenomenal,
and every single one of them has massive benefits, skills, and athleticism involved with it.
Here at the Swordsmanship Museum and Academy, we try to create a historical-based sword fighting
system, and with that, we have put together something that works hand-in-hand with these
well-researched and well-made archaeological recreations. Now, the most important thing that
you can know if you want to begin getting into Viking Age combat is to know that the shield
does not fit our modern-day ideas of how shield combat works. Instead, these Viking Age shields
are incredibly thin and incredibly light, and combined with the ability to hold it in the center
rather than having it strapped to your forearm, creates a very mobile and active defense that can
be used both in conjunction with your sword or as a separate piece to knock aside opponent's weapons,
creating openings that you can then take advantage of with your blade. In addition to that,
because you're holding it in the center, the shield itself can act as a weapon, as a massive
amount of weight when compared to the weight of an average human fist. With an additional foot and a
half of length in front of it, the shield itself, being cocked back and held next to the head in a
horizontal manner, can be used to punch forward and knock your opponent in whatever vital spot you
want. One last thing to note is that these Viking shields are, in fact, very thin. Incredibly thin
when you look at it from this perspective. They would, of course, be able to block against arrows
or sword cuts or possibly even some spear thrusts, but when you look at surviving depictions of
Viking-age combat, you'll frequently see that the Vikings are not holding their shield all the time
this way, but frequently holding it this way. This turns what otherwise would be a really small shield,
sometimes only a few millimeters thick in spots, into a shield that might be thin, but it's about
foot and a half deep, taking sword hits on the rim that have no hope of getting through to your vitals.
All in all, the Viking shield is a very active and mobile defense used both in conjunction with the
sword or sometimes independently. There's a whole world of interpretation out there, and I encourage
you, with the help of Birch House Woodcrafts, to go and explore it on your own. Thank you,
Birch House Woodcrafts. You guys have been fantastic, and we're really excited to see
what other cool historical products you're going to pump out in the future. Take care.
