Can Bacteria Survive in Highly Acidic (or Basic) Water. - Science Project

Terrific Physics
40 followers
Mar 14, 2026
This is a hydrothermal vent, a crack in the deep ocean floor where hot water and energy-rich
chemicals flow out, as you can see here. Many different types of microorganisms and animals
live here. It's thought that life on Earth, and possibly life on other planets, or possibly on
some of Jupiter's moons, may have begun at vents like this one. In this science project, you will
investigate whether there are microbes in a natural water source near you that could have
survived some of these early Earth conditions, including very basic and acidic waters. You will
attempt to culture these microbes on auger plates, which are also known as petri dishes, and on at
least some of your plates, you will likely end up growing some microbes like the ones you see here.
So you want to find a good water source that probably has a diversity of microbes,
so you can take your jar and just go ahead and fill it up. There you go, so we have a nice sample
of the water. All right, so you've got your water sample, and what you want to do next is fill up
each of your containers with the same amount of that sample. So here we are going to use about 100
milliliters, which is about the same as 0.4 cups, so the important thing is just to fill them all
the same amount. You want to mix up your sample a little first in case things settle to the bottom,
and then remove the lid and carefully pour out to 100 milliliters. All right, so we have our 100
milliliters of pond sample, and you're going to take it and put it into the first container that
we're going to use to eventually put on our auger plates. So we have just a baby food container that
has been cleaned and sterilized it with 70% isopropyl alcohol too. So, and similarly, you want to repeat
this with the next jars that you're going to be adjusting the pH in. So next we're going to test
the pH of just the normal pond sample, and so you can use these pH strips to do this. Always read the
instructions for whatever pH strips you're using. So these ones say to just put it in the test sample
for half a second, then shake the strip to remove excess solution, and compare it to the color chart.
So we're going to go ahead and take one of these out. All right, put it in here all the way down,
half a second, shaking the excess. So it looks like our pH here is right around 7, which is
what we would expect for this sample. So using a sterilized eyedropper that has been sterilized
with 70% isopropyl alcohol, and then let to air dry, we're going to add just two drops of the
distilled white vinegar to the pond sample and see how this adjusts the pH. It will probably end up
being around 6. So just two drops, one, two. So you'll want to repeat this process with the distilled
vinegar to create jars with pH of 4, 5, and 6, and then with an adult's help, you'll create a jar
using bleach with pH 8 and 9. And be sure to always follow all safety precautions when
handling bleach. After you have created these six jars, you will let them sit for 30 minutes
so that the different pHs will have time to affect the microbes. All right, so after you let the pond
sample sit at the correct pH for 30 minutes, then you are ready to go ahead and put it on the plate.
So to do that, we've got our auger plate here, all right, and we have these sterile applicators,
or they look like big Q-tips. So what you want to do is carefully open this end here
so that you're away from the part that you will spread on the plate.
And you only need one to start, so let's take one out. Make sure this doesn't touch anything.
You can dip it into your samples, swirl it around so it's nice and mixed. Don't let it
drip too much. And then we're just going to do a simple zigzag pattern on the plate.
I'm going to tilt it so you can see, but you do not want to touch the auger of the plate.
So we're just going to go back and forth in a zigzag pattern. I'm going to go all the edge,
all the way top and bottom, like that. There we go. Now it's ready to sit for a few days.
After you are done preparing all six auger plates with your water samples,
place them somewhere out of the way at room temperature, upside down, and check on them
each day for three days. So you should end up with little colonies of microbes growing on
your control plate. So the control plate is going to be the same pH as the pond sample,
probably right around pH 7. As you can see here, we've got lots of colonies which are
kind of whitish in color growing on this plate. So it successfully cultured those microbes from
the pond. Check on your other plates each day too, for three days, to see if they're growing
colonies that are similar to or different to the control plate. If you do see colonies on
other plates, that suggests that those microbes are able to survive the acidic or basic conditions
that they were treated with. There are many other things you can try for this experiment.
So for more ideas and written instructions, make sure you check out the link in the video
description. For over a thousand other projects in all areas of science and engineering,
check out our website at www.sciencebuddies.org.
