I Hand Sew Historical Princess Sleeves | Ever After 1490s Italian Renaissance - Part 4

Pre-modern Women's Fashion
182 followers
15 Video Views·Mar 14, 2026
Hey everyone, it's Abbey.
Today I want to continue my historically accurate Disney princess dress.
I'm recreating the court dress that Danielle wears in Ever After, A Cinderella Story from
1998, but with all of the 1490s Italian Renaissance layers that would have gone into dresses at
that time.
I'm working on the sleeves today.
I'll be using the same blog post that I used for the Gamora or Underdress.
They have a section on sleeves.
The link to the blog that I used will be in the description.
So let's get sewing!
I took measurements according to the blog post that I'm following for drafting the
sleeve pattern.
I start with a centerline and place all my measurements along the line.
I use my floppy measuring tape to create the shoulder curve that I need.
I then connect the measurements to create a straight line, and I label the initial pattern
and also add the measurements on it.
I fold in half and cut out the sleeve pattern I just created.
I now need to create the two separate patterns for the two sleeve parts on the Ever After
dress.
I trace the bottom half of the sleeve onto a new piece of paper.
I now have to create the lower sleeve part that lets the camicia show through.
I estimate where I want those to be and mark some measurements onto the sleeve pattern.
I also remove a few inches from the top because of the gap in the upper and lower sleeve.
I connect the lines with a curve to match the Ever After sleeve.
I label the pattern, fold in half, and cut out the lower sleeve pattern piece.
I try the piece on my own arm and realize some edits that I need to make.
I tape on some scrap pieces so I can extend the pattern a little bit.
I fold in half and cut my edits out.
I try it on and then cut off a little more to make it fit better.
I think it'll work!
Now it's time to create the top sleeve.
I unroll my pattern paper to trace the top half of the sleeve pattern.
I add a little extra to this pattern right off the bat.
I fold in half and cut out the pattern.
I try it on to see what I need to edit.
I remove some length from the bottom.
Now I want to create that sleeve shape at the top.
It's very similar to an inverted bottom sleeve,
so I use the bottom sleeve to kind of trace and have a similar shape, but with rounded corners.
I connect the lines with a curve.
I cut along the lines and label the pattern.
And there we go!
The sleeve patterns are drafted.
I get out my linen for the interlining layer.
I double the fabric and pin the pattern pieces in place.
I trace the seam allowance and cut out the pieces,
half inch for most and one inch for the sides.
I got out my poly olive velvet that I found at the fabric store.
I got real lucky with the color.
I didn't want to spend the money on the silk belt.
It was really expensive.
I figured out which way the pile was facing.
I want it to go down the arm.
I double the fabric, pile on the inside.
I place the linen pieces so the pile will flow correctly.
And I pin in place.
I cut out the velvet pieces.
This is the gold trim that I will be using.
I found it at Joann's.
I use a sharpie and the pattern pieces to trace onto the velvet pieces.
I clip curves and fold the fabric.
I fold and pin the velvet fabric in place to prepare to hand stitch it down.
I don't fold along the inside pieces.
I get some matching poly thread and whip stitch along the inside with invisible stitches.
I realized that the linen was going to be the interlining at this point,
so I needed a lining.
I have just enough of the cream silk from the skirt to use for this.
This will make the sleeves reversible.
I trace around the pattern, then I trace the seam allowance on.
I cut out the pieces.
The linen will interline the silk to create more structure to the sleeve.
I pin the pattern onto the linen interlining to cut off the seam allowances.
This will help the seams be thinner.
I pin the linen to the silk.
I clip the curves and fold and pin the silk over the top of the linen.
I mark the edges of the pattern on the linen.
Using white poly thread, I whip stitch the inside raw edges down invisibly.
I pin the gold trim in place along the olive green velvet sleeve.
I use matching thread and sew the trim on.
I fold the silk layer right sides to right sides and pin the inner sides together.
I use double thread and a hand backstitch to sew along the seam line.
I cut off the extra fabric to a half inch and finger press that down.
I sew those raw edges down with a whip stitch as well.
I'm using chainmail aluminum rings for my connecting rings.
I place three with hand stitches on each top sleeve.
I place corresponding rings on the bodice shoulder where they will attach with ties.
I also place three rings at the bottom of those sleeves, equal distance from each other.
I also place two rings on the bottom of the lower sleeve.
I pin the olive green velvet layer to the silk layer.
I use matching thread and a ladder stitch along the edges to attach the sleeve pieces together.
I hand top stitch with white thread on the silk side of the sleeve to make everything lay flatter.
And there we have it, the completed sleeves.
I have some gold ties that I'm using for attaching the rings to each other and to the bodice shoulders.
Thank you for joining me today as I made the sleeves for my ever after Italian Renaissance
princess dress. Stay tuned for the making of my snood and the giornia or overdress.
If you liked this video and want to see more sewing and costume videos,
remember to subscribe to my channel.
If you have any questions, let me know in the comments below.
Happy sewing!
