180° SKID TURNS LESSON - Fast Slide-Pivot U-Turn Technique - On Heavy Adventure Bikes

Adventure Ride Experience
9 followers
44 Video Views·Mar 7, 2026
Learn how to turn your motorcycle around fast! Works especially well on low-traction road surfaces. Take your time and practice. Bret demonstrates in detail with his R1200GS and a DCT Africa Twin.
End of the road!
All right, here's my options.
I could slow down and I could u-turn.
That's not a lot of fun.
I could stop, get off the bike and wrestle it around.
That sounds like way too much work.
I can put on a side stand and try to do a pivot.
I think the ground might be too soft.
Or I could use the momentum of the bike
and the lay of the land and let that do the work for me.
So I'm going to do a slide and pivot.
So the slide and pivot is just what it sounds like.
It's a combination of using the rear brake
to slide the back end of the bike around about 90 degrees.
And then you're using the power in the clutch to pivot
by spinning the back tire to pivot the other 90 degrees.
So you end up with a 180 degree turn.
When you do this u-turn, the idea is to find the right environment.
The places where you're going to find this most advantageous
is going to be in slippery surfaces where the bike already wants to slide.
If you're making a u-turn to go up a hill,
so if you're already going down the hill
and you need to u-turn to go back up the hill,
again, the bike is much more likely to slide naturally.
It makes it easy.
Or if you have very flat ground without big ruts in it
and you can get a nice momentum in and get the bike spun around.
When you choose to do a slide and pivot,
you've got to make the decision
before you get to the point you actually need it.
You've got to have enough momentum to start the slide in a straight line
and then get the bike kicked out sideways.
So during the approach, you'll disengage the power,
pull that clutch in,
and then you've got to stomp on that back brake,
get it locked up so you're in an in-line straight slide.
Then you kick the handlebars left and right.
That'll kick the bike out sideways
and the bike will start to slide out with the back end
trying to go beyond the front.
As the back end slides around,
you need to steer the front to continue going in that same direction.
It's almost like driving in the snow.
If you're sliding sideways, you steer the direction you want to go.
You carry that slide all the way into the 90 degree.
If the back end starts to go too far,
if it gets in front of you,
you apply just a little bit of front brake
and that controls the back slide
so it doesn't walk all the way around
and you don't have the back end slide out from underneath you.
Once you get that rear brake locked up
and that bike starts to slide sideways,
the bike's going to want to start to angle
and slide out from underneath you.
You need to move your body
and stay on top of the bike while it's sliding.
If you stay vertical and the bike leans and moves away from you,
it's going to slide out from you
and you're going to low side the bike.
That's not such a big deal,
but it's not what you're trying to do.
The worst case scenario is that bike starts to lean
and you get nervous and you let go of the rear brake.
If you do that, it can hook up traction
and then it'll high side you and catapult you off in front
and then the bike will come tumbling after you
and that's considered bad.
So once you start this, you're committed.
Either you slide the bike until it falls into the ground
or you do it until it's done right,
but you cannot let off the brake once you begin the rear brake slide.
Once you come to a 90 degree, come to a complete stop.
Now it's time to do the pivot.
We do this with power.
So once that bike comes to a complete stop,
turn the handlebars full lock in the direction you want to go
and then lean the motorcycle in that direction.
If you're not tall enough or strong enough to lean the motorcycle,
you can't do this part of the technique.
Crank it over full lock, lean it the direction you want to go,
get the revs up, throw the clutch,
the back of the bike begins to spin
and it pivots all the way around that front wheel.
Make sure you keep that handlebar full lock.
Once the bike's pointed in the new direction,
pull the clutch back in to get back in control of the bike,
stand it up and then ride off in the new direction.
When you get very good at this,
the slide and the pivot will be almost seamless.
You won't see yourself come to a stop.
But when you're first learning,
go ahead and put a little pause in there.
Don't expect to get this right the first time you do it.
If you're going to try this technique,
expect you're going to drop your bike at some point.
So take off the panniers,
make sure you're not going to damage things or injure yourself.
But also make sure you're on soft ground or mud
or someplace where when the bike drops,
you're not breaking things.
Now, if you are a shorter rider,
I mentioned that if you're short,
you've got to be able to get that bike leaned over.
There are still environments where you as a shorter rider
can really make use of this.
And I mentioned one of the places is going downhill
and making a U-turn to go back up the hill.
And the reason this works is that when you do the slide turn,
the bike's going to slide down the hill.
You're going to drop your foot on the high side of the hill.
That means that you're that much taller.
The bike is naturally leaned over
and you can do the slide and you can do the pivot.
If you've got a bike with ABS and traction control,
you're going to need to make sure your ABS is turned off
so you can get the brake slide
and you need to turn off your traction control
so you can get that back wheel spinning.
For those of you that run auto clutches or ride DCTs,
have no fear, you get to do this technique as well.
The only difference is instead of adding throttle
and throwing a clutch, you just add throttle.
If you really think you've got the slide and pivot down good,
you can do it to the right.
But no, you're not going to be able to drop the inside foot
and you cannot let go of the rear brake.
This is a technique that's really common in the dirt bike world.
We do it all the time.
But on a big, heavy adventure bike, it's not as common.
The slide turn or the braking portion
is a very easy technique to use all the time.
But the pivot requires things to be just right.
You need to have flat ground.
You need to be able to get slide on it.
And if you're heavily loaded, that's not going to work either
because if you have the traction,
the bike's just going to launch in a new direction.
This is the same reason why if you can't get the bike leaned over,
if you don't have the height or strength to lean it
and the bike is too vertical,
it will also go off in a straight line.
So it's a very unique technique for just the right environment
for just the right riders.
