How And Why To Make Insulated Track Sections

Toy Train Tips And Tricks
93 followers
25 Video Views·Mar 2, 2026
Episode 65: Track sections with insulated outside rails can be used to switch turnouts, activate accessories, control train movements, and create many other special effects on your Lionel, Marx, or other toy train layout.
This video shows a simple, cheap, and effective way to make them.
Enjoy!
AI Generated·May contain errors
Hello again, this is Mike with Toy Train Tips and Tricks, and today we're going to talk
about insulated outside rail sections, how to make them, and why to have them.
And we'll start with the first question, why to have them?
Well, one of the advantages of having three rail track is that both the outside rails end up being
part of the common. So you have a redundant rail that's really not needed for the circuit. You
need a hot and a common, but here you have an extra common. And so by insulating part of it,
attaching a wire to it, separating it from the other side, when the metal wheels of the train
come and activate the circuit on that insulated rail to that wire, you can use it as an on-off
switch to throw turnouts, to activate crossings, to activate gate men and other accessories,
or in conjunction with a relay, you can use it as part of a signal system or semaphores.
So this is essentially how the Lionel nonderail feature works. It's already wired in. For most
Lionel switches, it uses the inside rails with insulating pins. That's why you need the insulating
pins. Actually on this one, this is an early version of the N1122, which has it built in and
it uses the outside rails. But in any case, so in this case, from here to here is insulated,
is separated from the rest of the common, but there is a wire that attaches underneath here
that goes to the solenoid. So when the metal wheels of the train hit this, it completes the
circuit from this common to this common and turns on the switch, throwing it the appropriate
direction. Similarly, this side is insulated from here to here. The wheels touch here,
they bring the common from this side to this side, and it activates that side of the switch,
turns it on. So you can use this as part of your nonderail feature. It's built in,
or like I said, you can use it for crossing gates. You can use it for semaphores, any on-off
type activity. Sometimes you can use it to help with automatic train control or in conjunction,
like I said, with a relay, you can use it with signals or really anything you can come up with
where the train activates the on-off action of whatever you're doing. So how do you make one
of these and how does the track work? Well, you see with these metal ties, the tie connects
electrically the two outside rails through the tie, but here on the center rail, there is an
insulating fiber. This electrically isolates the middle rail from the common rails, and that
prevents your short circuit. Incidentally, over time, these can fail. And if you get a piece of
that has a short circuit in it, it's probably these fiber insulators, which are usually
cardboard or a really thin plastic sometimes, depending on the era and the manufacturer.
But over time, these can fail, get small openings in them, and then the electricity can go
and short the circuit. All right. So basically what we want to do is we're going to insulate
this rail from this rail. And to do that, we're going to add this type of insulation to
the outside rail. And then you can run a wire from that, put insulating pins on either end,
and that will make this section of rail electrically independent from this section
of rail. All right. So to do that, get yourself a small flathead screwdriver
and these, these metal, the metal is just simply crimped over the bottom of the rail.
And most of these will slide over without too much effort. If you get one that is really stubborn,
then the fast way to do it is to take your flathead screwdriver, place it in this slot
between the tie where the, the little crimp is and whack it with a hammer that will straighten
it out really fast. But most of them will come across without too much effort. So I'm going to
do it that way. There's the least amount of force possible here. That would be a little stubborn.
Let me try the inside. There we go. And once you get one side, it gives you an angle
to work the other side better. So step one is loosen these so that you can get the piece of
track out. Step two is to actually apply some type of insulator. All right. This one, I'm going to
give a little bit of an encouragement. It's a little better. Fascinating video right here. Okay.
All right. So we can pull, we can separate the rail and let's loosen these up a little bit more.
Grab some needle nose pliers. Let's pull these back. Give us a little bit more clearance.
I like to pull them as vertical as possible. So you see we're doing this in real time. This
has not taken a great deal of time to do this. Okay. So the next step is to add insulation
to these spots. And now you can see where the rail is crimped. That helps as a guide.
So there's a couple of ways you can do that. One, you can steal an insulator from an old
scrap piece of track, which is what this is here. And that can work if you've got enough
scrap pieces and you take the time to take them apart. But again, be very, very careful because
over time, especially here in these creases, you can get a really small hole and that's all it
takes for the electricity to want to jump across. So instead of doing that, I like to do my own.
And so I took part of a three by five note card and I pre-cut these, roughly the same size as
this, which about 16 millimeters square is what that comes out to. And let's put the light side
up. We'll just slide this in here in place. And you see it's big enough to get my fat fingers in
here. You see that's long enough to completely cover the tie, the metal tie. So we don't have to
worry about that. So again, if I can get my fat fingers in there, I'm going to slide this into
place. That one's being stubborn. Get in there. Okay. Give it a little old stay. Okay. Just enough
to hold it in place. Another thing that you can do, another option some people do is they use
electrical tape, which does work. I usually find when I try electrical tape, I get the pieces a
little bit too big. I have to go back and trim them. And the other thing is make sure that you're
using good quality vinyl tape and be very, very careful when you re-crimp the rails that you do
not puncture the tape and create a short circuit. Okay. So I'm going to slide the rail back where
it belongs. Now with the paper added, I might have cut one of them just a little bit too big.
This one also doesn't want to come back far. Let's bring this one a little bit wider. There we go.
Slide everything back into place. One, two, and three. All right. So before I crimp these back in
place, just to check the tie is completely covered. I said, I did cut these a little bit big, so I'm
going to have to go back and trim a little bit. It looks like, and it's also wide enough and placed
so that when I crimp this piece of metal over, it won't make contact with the rail. This one is a
little bit off. I'll redo this one so that I can get it neatly cover that crimp there. That's better.
Okay. So we're in place. Now I'm going to go back to my flathead screwdriver and I'm just going to
go back to these metal tabs and push it back over. That's one side. The other side. Okay.
So it's isolated now. I did cut these. It looks like a little bit big. So what I will do is I will
come back with an X-Acto knife and trim a little bit of this excess paper off on the inside. The
outside's not so important. I mean, I can trim it up to make it look a little better, but as long as
it's below the top of the rail head, it's not going to interfere with operation any at all.
On the inside though, you want it down here below the rail head so it doesn't interfere with the
flanges. And I'm going to tighten that up a little bit more. Let me get a bigger screwdriver.
Apply a little bit more force. There we go. We want this good and tight so that the wheel,
the rail does not wiggle. Okay. There. So I won't take the time to show you the trimming up,
but basically this is now electrically isolated from the other two rails. So what I will now do
is to use this, I will put an insulating fiber pin in this side. I'll pull this pin out and put
insulating fiber pin in this side. Or some folks for insulating pins will use wood toothpicks or
other solutions. But put an insulating pin on each side that keeps this completely isolated.
Then you will attach a wire to this. You can use a lock-on or you can solder a wire,
or I like to take wires with soldered spade connectors on and push them in there for a
solid physical connection. So you take that wire and you run it to whatever accessory you are
trying to activate to the common side. Then the hot side goes to your power pack, your accessory
power, and say you're running a crossing gate. There's two tabs. One tab goes to accessory hot.
The other tab goes here. And when the metal rail, the metal wheels of the train come by,
hit this section of track, the power will go from this rail to this rail to your wire and activate
your accessory. When the train's gone, no power here, no power to the common of the accessory,
the gate goes up and the lights go off and you are set. So that's how you make an insulated
track section for tubular track. Doesn't matter whether it's straight, whether it's curved,
you just peel back the tabs on all of the metal track ties, add insulators, paper, fiber,
or electrical tape, put it back together and run your wire and you're all set and ready to go.
So I hope you found this entertaining and informative. And if you like it,
please subscribe, like it, thumbs up, tell your friends, tell your neighbors, and
keep the trains running. And we'll see you next time on Toy Train Tips and Tricks.
