Episode 125: In this episode, my sons and I will build a simple but fun Lionel Christmas train display.
Our train village usually circles our Christmas Tree, but the addition of a puppy makes that an unwise choice for this holiday season. Instead, we looked to a Foosball table in the Rec Room to elevate the layout out of harm’s way.
For a base, I picked up two packs of 14.5” x 48” white Styrofoam sheets at Home Depot. These Hand Packs are not only easier to transport in the car, but they are also easy to configure in various shapes for the final layout.
The first step was to trim two sheets to fit inside the play area. These sheets lay across the control rods for the Foosball players, providing basic support for the layout.
Next, I laid out four sheets of foam in a 48” by 58” pattern and taped the edges together - just enough to keep them from separating. I then flipped this panel over so the tape was on the bottom and roughly centered it over the foosball table. The white Styrofoam will provide a “snowy-looking” structural base for the display.
Next, I laid out an oval of standard O-31 tubular track, making sure the track remained - as much as possible - over the wood structure of the foosball table. The outside edges of the foam have no underlying support and are only strong enough to support some light scenery - not trains.
Next, I added two Lionel power lockons - one at the front and one in the back for even power distribution - and poked small holes in the foam to accommodate the wires.
Next, we unpacked our ceramic village and laid out the buildings across the table. We tried several different village configurations before settling on this particular plan. Then, we ran the wires for the building lights. One advantage of the O-31 track is the ties are tall enough to allow the light cords to pass underneath the track.
We decided that we needed a tunnel to add visual interest and to hide much of the oval. We wired the rear track lockon at this point as it would be located inside the tunnel.
To make the mountain, we cut one of the Styrofoam sheets into two 7 ¼” x 48” sections and measured a location for a tunnel portal on each side. To support the walls but keep the construction modular for reuse next year, we inserted wood toothpicks into the wall edge and pushed the wall neatly into the foam underlayment, overlapping the panels to match the table width. We repeated this process - without tunnel portals - for the back wall, and then layed one complete panel and a portion of another across the top securing these in the same manner. Next, commercial snow blanket material - recycled from last year - provided texture for the mountain and concealed the light cords for the village structures.
To add some operating interest, I added an old Marx block signal to the front of the layout and wired it to enable an observer to stop a train at the station by changing the signal from green to red or yellow. The original Marx bulbs were burned out, so I replaced them with my standard E10 screw base LEDs that I use for most Marx projects - headlights, turnout indicators, etc. The bulbs are clear, so my son painted them the appropriate colors with inexpensive Apple Barrel acrylic paints.
Then, I completed the wiring, and we added additional scenic features - people, trees, an ice skating pond, and my son insisted on additional lighting for the display.
And here’s the final product!
**As an Amazon Associate, I may receive commissions on qualifying sales from these links**
Toy Train Tips And Tricks is a channel devoted to the operation, repair, history, and collecting of classic 3-rail O and O27 gauge trains made by Lionel, Marx, K-Line, Menards, and other manufacturers.
Building the annual Christmas train display on this episode of Toy Train Tips & Tricks.
Hello again, this is Mike with Toy Train Tips & Tricks. In this episode, my sons and I will
build a simple but fun Christmas train display in an afternoon. Since we did this construction
as a family project, most of this episode will be in slideshow format. In order to avoid YouTube's
restrictions on minors and videos, and to avoid any copyright complications with the music that
we had playing in the background while we worked, our train village usually circles our Christmas
tree. But the addition of a puppy to the family makes that a very unwise choice for this holiday
season. So instead, we looked to a foosball table in the rec room to elevate the layout
up and out of harm's way. For a base, I picked up two packs of 14 1⁄2 inch by 48 inch white
styrofoam sheets at Home Depot. These handy packs are not only easier to transport in the car,
but they're also easy to reconfigure into various shapes for the final layout.
The first step was to trim two of the sheets to fit inside the foosball play area. These sheets
lay across the control rods for the foosball players, providing some basic support for the
middle of the layout. Next, I laid out four sheets of foam in a 48 inch by 58 inch pattern,
and taped the edges together just enough to keep them from separating. You don't have to use too
much. I then flipped this panel over so that the tape was on the bottom and out of sight,
and roughly centered it over the foosball table. This white styrofoam will provide a snowy looking
structural base for the display, and is modular and can be reused next year. Next, I laid out an
oval of standard 031 tubular track, making sure that the track remained as much as possible over
the wood structure of the foosball table. The outside edges of the foam have no underlying
support, and are only strong enough to support some light scenery, not trains. Next, I added
two Lionel power lock-ons, one at the front of the layout and one at the back, for even power
distribution, and I poked some small holes in the foam to accommodate the wires. Next, we unpacked
our ceramic Christmas village and laid out the buildings across the table. We tried several
different village configurations before settling on this particular plan. Then we ran the wires for
the building lights. One advantage of the 031 track is that the ties are tall enough to allow
for the light cords to pass underneath the track. We decided that we needed a tunnel to add some
visual interest to the layout, and to hide much of the oval. We wired the rear track lock on at this
point, as it was going to be located inside the tunnel. To make the mountain, we cut one of the
styrofoam sheets into two 7 1⁄4 by 48 inch sections, and measured the locations for tunnel
portals on each side. To support the walls, but to keep the construction modular to reuse next year,
we inserted wood toothpicks into the wall edge and just pushed the wall neatly into the foam
underlayment, overlapping the panels to match the table width. We repeated this process,
without tunnel portals, for the back wall, and then laid one complete panel and a portion of
another across the top, securing these in the same manner with toothpicks. It doesn't take much to
hold these things together. Some commercial snow blanket material, recycled from last year's project,
provided texture for the mountain, and concealed the light cords for the village structures.
Then I completed the wiring, and we added some additional scenic features. People, trees, and my
son insisted on adding additional lighting for the display, including inside the tunnel. To add
just a little bit of interaction on the layout, I took this Marks 404 lock signal that was featured
in one of my very earliest videos, and added that to the layout. I replaced the original Marks bulbs
with some LEDs. These are E10 screw mount LEDs. These are the same ones that I used for my Marks
replacement headlights, and the replacement bulbs of my Marks turnouts. They fit the signal
wonderfully. They were white, and we just added some of these apple barrel craft paints to make our
red, yellow, and green indications. And as you move it to green, the power is restored and the
train moves. If you want to see how I wired this up, here is the link up here to the video from about
two years ago now, where I showed you how to do this. Once everything is in place, we've got it all
lighted up, and it's just a matter of adding the decorations, the people, the buildings,
the little scenery items. A lot of this stuff came from dollar stores. Our brick road came from
Dollar Tree this year. Some of our figures as well, some of the trees that we're using.
The Santa and Reindeer is actually a cake topper, and there is a link in the description
to where you can acquire that. For power, right now I'm using a Christmas Beat from Readymade
Trains, based on old Tucson tooling. We swap out, we use some steam locomotives as well.
And for our passenger cars, we have a couple of the Southern Crescent cars that I rewired for
new LED lighting as well. Buildings themselves came from a collection, I believe this was from
Kmart, from oh, 30 years ago now, that my wife purchased at an after Christmas sale. She bought
the whole village at once. They're pretty well sized for O scale. Again, some of the people came
from Dollar Tree this year. Some are old bottle power figures, and some were originally designed
to be Christmas ornaments for small Christmas trees, but you cut the strings off, and then
you have a group of carolers here by our train station. As always, I hope you enjoyed watching
this video as much as I enjoyed making it, and if you did, please like it, subscribe, share it,
and leave a comment about your favorite holiday train traditions. Tell your friends, tell your
neighbors, keep the trains running, and we'll catch you next time on Toy Train Tips and Tricks.