Lionel Trains revolutionized the operation of O gauge toy trains in 1936 when they introduced remote electronic uncoupling. Early uncouplers used a special 5-rail track section that could activate a solenoid inside the coupler itself, releasing the knuckle with a spring.
By 1948, Lionel had introduced a new magnetic coupler system using a magnet placed between the rails. The magnet pulled a plunger in the coupler, releasing the knuckle.
The O gauge UCS track section and the O27 #6019 section utilized both rails and magnets so they could operate both types of couplers as well as various operating accessories.
From the late 1960s onward, Lionel’s O27 uncoupling sections lost their activating rails and used only an offset magnet for uncoupling and unloading. The O gauge UCS section continued production until as late as 2017.
But regardless of type - rail, magnets, or both, Lionel’s uncoupling sections were ALWAYS full sections of O or O27 gauge track, and the firm NEVER made an uncoupler for curved track. This, we must do ourselves. coupler itself, releasing the knuckle with a spring.
By 1948, Lionel had introduced a new magnetic coupler system using a magnet placed between the rails. The magnet pulled a plunger in the coupler, releasing the knuckle.
The O gauge UCS track section and the O27 #6019 section utilized both rails and magnets so they could operate both types of couplers as well as various operating accessories.
From the late 1960s onward, Lionel’s O27 uncoupling sections lost their activating rails and used only an offset magnet for uncoupling and unloading. The O gauge UCS section continued production until as late as 2017.
But regardless of type - rail, magnets, or both, Lionel’s uncoupling sections were ALWAYS full sections of O or O27 gauge track, and the firm NEVER made an uncoupler for curved track. This, we must do ourselves.
**As an Amazon Associate and a member of other affiliate networks, We may receive commissions on qualifying sales generated from the links on this channel.***
Toy Train Tips And Tricks is a channel devoted to the operation, repair, history, and collecting of classic 3-rail O and O27 gauge trains made by Lionel, Marx, K-Line, Menards, and other manufacturers.
Uncouple your trains almost anywhere on this episode of Toy Train Tips and Tricks.
Hello again, this is Mike with Toy Train Tips and Tricks, and today I've got a little conundrum
on my layout. Those of you who have been longtime viewers know that in addition to
just running the trains around the layout, I like to operate. I like to do switching,
and in this case, in order to do the proper operation I intend to do with my power plant,
I need to be able to uncouple cars here so that I can then cut loose from them and then drop them
off in the siding and vice versa. But this is a curved section of track. Lionel did not make any
uncouplers for curved sections of track. Now luckily, this is a wider radius. This is an O42,
which is going to make this easier, but basically what I'm going to have to do
here is I'm going to have to perform a little bit of surgery. So I'm going to take this 6019,
and I'm going to do a little surgery, cut the magnet out, insert it here, and have a magnet
here. You'll be able to use this process to put uncoupled wing magnets anywhere on your layout.
I have another one, which I'll also show in this video, which is a straight piece of track. However,
it is a short piece of straight track, less than a half section, and the track has already
been ballasted and I need to install an uncoupler there. So we'll show that process as well. By the
way, this will work not just with the 6019, but also with the later design with the single magnet
off to one end as well. So let's get to the workbench and let's get started. Lionel revolutionized
the operation of toy trains in 1936 when they introduced remote electronic uncoupling. Early
uncouplers use a special five rail track section that could activate a solenoid inside the coupler
itself, releasing the knuckle with a spring. By 1948, Lionel had introduced a new magnetic coupler
system using a magnet placed between the rails. The magnet pulled a plunger in the coupler,
releasing the knuckle. The O gauge UCS track section and the 027 number 6019 section utilize
both rails and magnets so they could operate both types of couplers as well as various operating
accessories. From the late 1960s onward, Lionel's 027 uncoupling sections lost their activating
rails and used only the offset magnet for uncoupling and unloading. The O gauge UCS
section continued production until as late as 2017. But regardless of type, rail, magnets, or both,
Lionel's uncoupling sections were always full sections of O and 027 gauge track,
and the firm never made an uncoupler for curved track. This we must do ourselves.
While I'm using 027 uncouplers in this video, the concept would also work for regular O track
and UCS sections. Also, I'm unsure whether this will work on curves tighter than 042,
as the severe curvature of the rail may place the uncoupling magnet out of alignment
with the activating plungers on many cars. And yes, Lionel does make uncoupling and
activation sections for their fast track system today as well.
Okay, so now I'm going to take my rotary tool, and I'm going to cut right here where the track
starts to flare out for the magnet. Right here, and right here. And with the rotary tool, safety
first, make sure you're wearing your safety glasses, and let's begin. Using a screwdriver,
I'm going to pry this middle section out. Okay, hold on to that, you're going to need it later.
And now I'm going to disconnect the wires underneath, and then I should be able to pull
the magnet right out. Leave yourself as much wire as you can. To leave myself as much wire
as possible, instead of cutting this wire, I'm going to unsolder it. Go! Alright, salvaged a good
length of wire. Now let's remove the electromagnet. Okay, so there's the guts. Then we're going to
reinstall and rewire this in our new piece of track. Okay, and before I go any farther, I am
going to save myself some headache later. I'm going to extend these wire leads to make it easier on
myself later on. Meanwhile, back at the layout, I'm going to take the metal piece that I had cut off,
I'm going to lay it here on the center rail where I want to install my magnet, and take a sharpie,
and I'm going to mark the outside of this, but I'm actually going to cut the center rail about a
quarter inch closer to the middle on each end. And the reason for that is I'm going to use these
little wings to crimp on to the existing center rail to help hold everything in place.
So, back to our rotary tool, and again, safety first! Get those masses on.
Oop, and that's why you wear safety masks. Remove that piece of rail, and let's test fit.
Right like that. We'll have our magnet here, and we're going to crimp
our sides down over the existing rail to hold everything in place. Next, let's drill a hole
for our wires, and clean up my mess with the shop vac. Feed the wires. I might have cut the rails
just a little bit too short, but I'll make it work. Okay, that's the general idea. Now, to hold
everything in place, I'm probably going to put just a little dab of some glue on there to hold
everything where it's supposed to go, but that will work nice. Okay, I've got a generic silicone
based glue here. I'm just going to go around the edges. There we go. Everything's kind of in place.
I'm going to let this dry for about an hour until it sets up a little bit, and then I'll come back
and crimp my tabs onto the center rail. So, it is now dry. I'm going to position
on the center rail, and I'm going to get ready to crimp it into place, and then I'll use my
end nippers to complete the process. Okay, you may find that you need to put a little shim
underneath this to keep it from dropping down, but this seems to be in good position. All right,
some additional things that I've done. I did add some solder to both ends, both to ensure
electrical continuity through the center rail, and also just to make sure that this thing is
not going to slide back and forth as the train rows over it. Also, I added some ties to help
support the rail since this was a cut piece and we're missing some stuff, and I did add a small
thin wood shim underneath the magnet to get it up to the proper height. So, now everything's
secure. We're not going anywhere, and it works. Now, on this side, even though it is a straight
section that I'm putting the uncoupler in, it does present its own challenges. First of all,
it is shorter than a half section. I had gotten impatient and had already done some ballasting
here, so I want to disturb this as little as possible. So, the easy way would be to take one
of this style with the single magnet offset and just cut it to length and insert it, but again,
probably will disturb quite a bit of ballast. So, I'm going to try to minimize that by just
dealing again with the center rail, and I could cut up one of these, but I have a bunch of 6019s
that I got for dirt cheap at a show last year because nobody wants to rewire these things.
So, I'm going to be using a 6019 instead, just like I did on the curve, and so here we go. This time,
I cut it out a little wider, keeping these retaining clips that hold the original piece
into the mounting bracket. I can use these to better clip on to the center rail, giving myself
a better both mechanical and electrical connection.
That's the fit. Good. The wire's down inside. Okay, we're now all crimped into place.
All right, and we have an uncoupler on a short section now as well. By leaving myself these extra
crimp sections, I was able to get it down without having to use any adhesive on this one. This one
is all mechanically held in place. It is good and firm. So, go a little bit wider, leave those
tabs in place, and those will help you crimp the track into place. And the most important question,
does it work? It does! I hope you enjoyed this video as much as I enjoyed making it, and if so,
please do the usual like, subscribe, and comment. But before we go, this channel has reached two
impressive milestones this week. Six thousand channel subscribers and one million total channel
views. That's not bad for an old guy playing with trains in his basement. Seriously though, I thank
all of you for your support and your willingness to spend your precious time with this channel.
Many of you have commented about my lack of personal appearances on these videos that
I've never shown my face. Well, in celebration of these milestones, by popular request,
I will now show my face. But I think you're gonna regret it. Okay, here goes. Three. Two. One. Ta-da!
That's me on the left. On my right is my uncle, who some of you Florida residents may know as
Tamoka Joe. In the background is Reading Class T1484 number 2101, then in service as AFT number
one on the American Freedom Train. So thanks again everyone for watching. I can't wait to
see the comments on this one. Until next time, keep the trains running, and we'll catch you next time
on Toy Train Tips and Tricks.