Slowing Down the Kitchen Ceiling Fans

TV Electric Fan
2 followers
15 Video Views·Feb 25, 2026
I can usually get a good low speed by setting both the wall control and the fan's onboard controls to low. In this case, these fans are such high speed that even the low in that configuration is too fast f or my preference.
Here's the ceiling fan in the dining room. There is an identical ceiling fan in the kitchen
and they're both controlled by these kind of lousy hunter three speed controls.
On most 52 inch fans I can set the fan's onboard controls to low and set this control to low
and get a really good low speed out of it. But with these high rpm 36 inch fans
I have not had such results. Sometimes with these capacitor based controls you can connect two or
three fans to the control as opposed to just one and get an even slower speed out of it.
So we're going to go ahead and try that today. Eventually these are going to be replaced with
infinite range voltage regulating control to solve this. But for now let's see if we can
kind of set up a workaround. I think it should be pretty simple to just
swap the connection from one of these controls onto the other side.
Oh they're common screws. I don't like those. It doesn't fit. It's important to have the right
bit because otherwise you might strip the screw or in this case it just won't work at all. Okay
that's the right bit. Okay so we have fan and light controls here. I don't remember which.
This is one of the reasons why I don't like these controls. You have blue and red or which one is
the light and which one is the fan. I guess we'll just have to find out by taking one off and seeing
what changes. So this is the high side into the controls. Let's take the blue off and let's see
what we get here. Okay so the blue is the fan. So what we're going to do is we're going to take
both of these wires that go to the fans. For now we'll just cap this off. Let's see if that gives
us a better range. Well one of them is working one of them is not. I wonder if the bearings are
just too stiff for it to start up now. Huh that's perfect. I was not really expecting that to
do exactly what I wanted. This is interesting behavior because the one on the left here
was installed first and that has I've put a decent number of hours on that to free up the bearings
and that one usually runs faster whereas this one would run slower because the bearings haven't been
used at all. And now we're noticing the opposite. That one's running faster and this one is barely
able to maintain. Very interesting. So this is on that's or was that on medium? That's high.
So that was able to start by itself so it shouldn't stall out.
Maybe there's a rough spot in the bearings. Hello? Good afternoon my name is Ariana. I'm calling from
the Senior Resource Center. Nailed you about the new state regulated plan that helps with final.
Have you lied today? No this isn't a scam it's just about the new cash borrow update for final
expense insurance lets you access up to 90 percent of the. You smell like rotten eggs.
It's a scam. Well I answered it anyways. That's very interesting. So that one is running a little
bit slower than this one. I'll try to bump it up to medium and see because we you know we have
with nine different permutations we can work with on here. I can always drop this now this one's
going a little too fast. I can drop this one down to medium and see if that kind of gives us the
desired results. Now that one's going a little too fast now. Let's drop this one down to medium.
I'm going to put this one to low now and I'm going to put this one to low as well.
Now that one you can see it's slowing down pretty quick. I think the bearings are not
as good in that one which is odd because that one has more run time on it. I guess low on the
controls and high on the fan was the best option. I'll put this back together now because we'll
keep it like this for now until I get a better control system here.
Whatever that might be. Ah you're working with the power on. Yes yes I am. That one is really
going ridiculously slow now. What I might have to do is put him on high for a little while get the
bearings warmed up and then drop it down again. Does this say what the maximum load is? Oh wow
it's only 1.6 amps. These probably are not more than 0.7 amps a piece I wouldn't think.
Wow this wall is filthy. What the heck? I gotta get this repainted. This is awful.
I never noticed that before. Good grief. This wall looks like it slid down a cliff full of road salt.
You know what the problem is? Why I'm seeing that? Because there's snow on the ground
so it's extremely bright in the house today. Lighting probably just isn't good enough to
show the dirt on a regular basis. These look like new screws. I wonder if this is what it came with.
I don't know why anything would come with these types of screws at this point in time.
It should all be Phillips. All right now we got to see where they have to be aligned
according to the plate here. That's a pretty good speed right there. Maybe a touch too fast. That's
like 30 rpm. I like around 20 to 25. This is a touch too slow. That's probably only about 15 rpm
but this is better than what we had before so this is an improvement.
And this is only a temporary fix. I have the permanent fix. I just need to spend the time to
put it in.
