Are you tired of seeing your ceiling fan wobble? Did you know it’s a simple process to get that wobble to go away? DirtFarmer Jay will walk you through the steps to get that fan running smoothly and looking great again!
Not only is it annoying to see a ceiling fan wobble, but it’s hard on the motor as well, introducing unnecessary wear that leads to premature failure of the fan. Those of us that JUST DO IT YOURSELF are too “thrifty” to have to spend money on replacing something before you have to!
You can buy a very inexpensive fan balancing kit ($2 or $3), or you can make your own using a common office binder clip and some washers and glue. If you go the DIY route, you’ll also need some double sticky tape for temporary weight placement.
There are four things that you must look for when balancing a fan: 1.) what speed is the wobble the worst? 2.) Are the fan blades all attached the same way to the blade holders? 3.) Are the fan blades all the same angle and the same distance from the ceiling? And finally, 4.) Are any of the blades heavier than the others?
Fortunately, determining all these things are easy to do by measurement or by a simple sequence of trial and error. You can invest 10 to 15 minutes and eliminate that wobble and the hassle that goes with it! Quit avoiding certain speeds on your fan, listening to clinking pull chains, or just putting up with it. With what you will learn, you can get rid of the aggravation and when someone asks how they can take care of the problem on their fan, you can say, “You can JUST DO IT YOURSELF!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Do you have a wobbly fan like this one?
Well, you don't have to live with it.
Stick with me, and in four easy steps,
I'll show you how to never live with this again.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
You know, a wobbly fan can drive you crazy,
but it's not good on the fan either.
It's hard on the motor, it wears things out prematurely,
and why replace things sooner than you have to?
Let's make longer use,
better economics of the things we've got.
But if you've got a fan that's doing this,
there's some easy steps you can follow
to get it taken care of.
So the first step you've gotta do
is determine when it's behaving the worst.
Well, I had set this fan on all three speeds,
low, medium, and high,
and the wobble you see right here
developed the most strongly
and was the most pronounced on low speed.
So let the fan run at whatever speed it is
where you're gonna do
all of your other testing and adjustments,
because if you can get it solved there,
it'll even out on everything else.
So step number one,
find out when the wobble is the worst, what speed.
Step number two,
what you have to determine is whether or not
each of the individual fan blades are in the same plane.
Are they tilted up a little bit?
Are they level all together?
Is one down?
And the way you're going to do that
is you use a fixed point.
In this case, we're gonna go to the ceiling.
I'm gonna put a tape measure
and bring it up close to the center point of the fan blade.
And we can see in this one,
it's right at about 12 1⁄4.
Let's go ahead and bring another one around,
see what we get, and let it settle.
And that one's close enough.
Again, at 12 1⁄4.
Notice that when you come around,
the motor is suspended.
Whoa, whoa.
Look at here.
This is most likely one of the big issues.
So here we have a 11 1⁄2-er.
So we'll keep note of that.
It's a third blade.
And you can use a silver.
So here we got 11 1⁄2, all right?
And then we'll do one more just for grins.
And we're back at 12.
So it was probably these two right here
are the most problematic.
Yep, that's a high blade and so forth.
So what you're going to do at this point
is check to make sure that all the screws
that are tightening the blades on are all tightened together.
See if that takes an issue.
If it's been running for a while,
and we've had this fan for maybe 15 years,
it's likely they've come loose a little bit.
And if they are tightened,
then you're going to look at the bracket itself,
which you can see right here,
these brackets to see if they're mounted correctly
or if they're bent slightly,
and you can kind of adjust this.
So let's go ahead and check the tightness of these.
This particular blade was the one that's problematic.
So I'm going to take a Sharpie pen.
If you have a silver one,
that's even better for these dark colors.
And I'm going to put an X up here
or a little reference mark on the back edge too,
just so I can see which blade it was that was there.
And we'll go ahead and stow that and get ready.
Now, the next thing we're going to do
is go up here and look at these screws
and sure enough,
we've got some of these screws that work loose.
So I'm going to go ahead and tighten this all down again,
to just take out the slop and the blades.
And we're going to do that with all five blades.
Let's go ahead and check our blade height to the ceiling
from the same point.
And here we are, we're going to let that settle again.
All right, we're close to 12.
We're pretty doggone close to 12.
Let that settle in again.
That one's drooping just a bit.
We'll see if it causes a problem.
All right.
And these are all,
you're probably not going to get exactly the same thing
every time, but we're pretty close.
All right, let's go ahead and turn it on
and just see how much we've improved our situation.
You saw the wobble at the beginning.
Let's look and see what we've got now.
All right, as you can see,
there's very slight improvement.
We've actually made a dent in it, but not enough.
And I would imagine if we turn this to higher speeds,
it would probably get more pronounced as well.
But we're going to go ahead and adjust from here.
So what have we got?
We most likely have a weight distribution problem.
One of the fan blades is weighted differently,
needs a balance or a weight put on it.
This is where the majority of your time
is going to be invested in adjustments
because there's trial and error in this.
And you'll need to shut on and off the fan
as you put the weight on different places.
I will tell you this, when you shut off a fan,
don't be tempted because of the wind down time
to just grab a blade and stop it
because you'll probably unbalance it more, okay?
So be patient, let it wind down,
and then we're going to place that.
So let's go ahead, shut this off.
We're going to pick a fan blade
and we're going to use this little kit,
which you can purchase from any home improvement store.
This one happens to come from Home Depot, just over $2.
And what you've got in is two sticky back weights
plus a trial weight or a clip
to put onto the edge of it and move it around.
It's repositionable until you can find out
where you're getting the improvement.
So let's go ahead and shut off the fan.
Earlier on, one of the blades that was the most off
and was up, I went ahead and marked.
And so we're just going to try using that one to begin with.
Here's a little clip-on repositional weight.
And so what I'm going to do is I'm going to take this
and put it up on the fan
and just to throw a little bit of a different weight on it.
And we're going to turn it on
and see if things get worse or better.
Here we go.
Well, that clearly wasn't it.
The method I like to use is to go diagonally
or across from where I last weighted it.
So the weight is out over there.
I'm going to put it on one of these blades here,
closer to you.
Let's just try it over here and see what we get.
We tried here and we did a skip.
We're going to go ahead and turn it back on
and we'll see, did we get better?
Did we get worse?
Nope, it isn't that one,
but we are seeing a little bit of improvement.
Let's keep trying.
We now found the best balance point.
If you look over here, this is hanging just beautifully.
Hardly any movement at all.
Just very, very slight, but certainly acceptable.
Well, let's go ahead and stop the fan.
I'm going to show you where that weight ended up.
All right, where it ended up,
this was the blade that gave us the most improvement
when we put the weight here.
Now we experimented up and down the length of the blade.
And once we've placed that sample weight
all the way out here, everything came into balance.
So now what we're going to do is replace that
with a sticky pad with a little weight on it
on the backside of this, and we'll test it one more time.
Let's do that.
All right, let's go ahead
and put one of these sticky back weights.
I've gone ahead and peeled off the backing on it.
We're just going to put it out here near the tip,
press it in place, remove the temporary weight,
and let's go ahead and test it
and see if our efforts paid off.
So after putting that weight where you saw us place it,
this is the results.
Very little movement, nice balance.
We've solved our issue.
Well, if you have a technique that has served you well
in balancing these kinds of devices,
won't you share it in the comments below
and we'll help get the word out.
If you found this video to be helpful, won't you like it?
And better yet, subscribe to our channel.
And when you do, press the bell or ring the bell
and that'll immediately inform you
approximately every Friday when we publish a new video
about home skills like this out in the shop,
the garden, the kitchen, truck life,
or just great product reviews for hands-on living.
Until the next time, this is Dirt Farmer Jay.