Second Floor Ep. 10 Building Our Earthen Home

FFG - Food Forest Garden
176 followers
17 Video Views·Feb 25, 2026
How to build second floor for earthen hose.
When we build the wall up to the level that we need, it can be 270 centimeters or 300
centimeters up to each person, how do you like it. And after that, the top of the wall may be not even,
it may be up and down like a wave, but it doesn't matter because we are about to put the
beam on top of it. If we build the first floor, this beam can be the base of the roof. But if we
going to build second floor, this beam is going to be the second floor, the beam for the second
floor. So the technique is quite simple. This is the top view of the wall of the house. It's about
12 meters by 12 meters. This is the side of the house. This is our first beam. The beam has to be
on top of the wall as much as we can. If it can be in the middle of the wall, that is the best.
And in this beam, we stick out one meter at least each side. That side is one meter. And if
we stick out more than one and a half meters, we need to have the pillar to support it. If not,
it can sag. This is the first beam. And then the second beam is going to be far apart from the
first beam, not more than three meters. Normally, it can be closer than that, but it should not be
further than three meters. This is the second beam. And the third beam, we try the second beam
and the third beam quite close together because we try to put the beam on the wall as much as
we can. That's the reason why the second beam and the third beam are quite close together.
So, the first layer of the beam, we have four beams for this house. And then the end of each
beam will stick out one meter each side. And this is the first layer of the beam. The next thing we
have to do is the second layer. The second layer, we will start with the end of the wall each side
like this one. So, we want to make it square as much as we can. So, the first one,
the first beam will be at the end of each side. The beam of the second layer, we will have many
of them. And each of them will be about 40 centimeters far apart. But at the beginning,
we put only two at each end like this. We put two because we can check the corner. We need to make
the corner 90 degrees exactly. And at the end of each beam, need to stick out one meter at least
also. Sometimes, if we want to make it overhang wider, we can stick out more. But we need to have
more pillars to support it. When we put the second layer of the beam on top of the first layer of the
beam, we need to check these four corners to make it 90 degrees before we weld together. So, every
corner, four corners, have to be 90 degrees exactly like this. It will be easier when we go
to the next step. And after we check with the 90 degrees like this, next time, next thing we need
to do is pull the string to check, diagnose like this. If it's equal, that means every corner is
exactly 90 degrees. This is the way we check, recheck it again if it's 90 degrees or not.
We normally use the long measuring tape to check across the corner to recheck again
if it's exactly 90 degrees or not. And then after that, we will check the top of the beam
is even or not. So, if it's too low, we use brick to support it or use wood or anything
raise it up high to the level that we need. After we check four corners,
make it even. It can be 300 centimeters from the bottom or to 70 to 50 is up to each house.
And then the next thing is we put the second layers of beam. Each piece will be about 40
centimeters far apart because we will put one kind of board we call smart board. It's a mixture of
cement and paper or some kind of fiber. It's quite strong. If the board is thick,
we can make the beam wider. But if the board is thin, we can make the beam closer.
If there's some corner that the floor sticks out from the wall more than one meter, we always
put some beam to support it. That will help to make it strong. In this case, we use temporary
pillars first and then we put the real pillars later. After we check all the beams even, the
top of the beam is very even, we can put the rest of the second layer of beams on top of it. This
second layer of beams is going to be the beam that carries the floor. The floor can be cement,
can be wood, can be anything that we want to have. It depends on each house.
After we finish the beam, we need to fill up the gap between the wall and the beam and cover the
beam with mud. So we don't have anything to connect the beam and the wall together. We just
cover with mud. This is some part of bricks that we support the beam to make it even.
Sometimes we have a lot of them. And then before we put the floor, we need to cover
with the beam with mud. And any part of the metal beam that has to be in the mud, we always
cover with plastic like this. Because sometimes when it's exposed to the mud,
sometimes it can rust even we paint over it. In the past, most all the houses that we built,
we never covered with plastic like this. But when we took down some of the houses,
we found that some part of it was rusty. So this time we want to experiment to cover with
plastic first before we cover the whole beam with mud. And then after that, we just build up to cover
the beam, make it even to the top of the beam. And then we can put the floor on top of it evenly.
It will be easy. This is the smart board that we are going to use. It's the same size with plywood,
but it's thicker, about 16 millimeters. It's a mixture of cement and some kind of fiber. I don't
know. It can be paper. So we paint one side of it. That side is going to be our ceiling. So this
side is what we paint. We have to be careful when we move it up. So it will be nice and clean. We
don't need to clean a lot after that. But the top side of it is rough. This side will pour concrete
over this area. So we don't need to worry much about this side. Then we seal the gap between
each smart board with sealant. It can be cement or can be grout. Whatever. We can use it. And then
where we will have the overhang far, it's good to have the pillars ready for that area. This pillar
will be finished before we pour the concrete. And then after that, we use two by four to make the
edge before we pour the concrete. Because the layer of the concrete will be about two inches
thick. That's why we use two by four. And after that, we will pull the string to see where is
going to be the wall. And then we can know where is going to be our bedroom. And then we can
make a hole for the septic tank, for water, for drainage pipe. So this part,
we need to do it before we pour the concrete. That will make things a lot easier.
Before we pour the concrete, we put the wire on top. So this is what we call wire mate. It will
help to hold the cement together. This is very convenient for us. After we put wire mate all over,
we can support the bottom. If the wall too far apart from each other, we need to support it
to prevent sagging. Because when we pour concrete, it's quite heavy. If we don't support it, it can
sag maybe a few centimeters or more than that. It depends on how far it is. To support it is
worth it. It's important to do that because when it sags, we cannot fix it anymore after it dries.
And then we use two by four as a level. When we pour the concrete, we prepare a long piece of
metal, two by four, and then level it. Second floor, if we can have crane, it will help a lot.
It makes things a lot easier. Crane will help to lift the cement from the bottom up to the top.
That's very convenient for us. When we use two by four to level the whole thing, it makes it very
easy and make it even in the big area. It's very convenient with the long two by four like this.
Two people maybe need to help each other to pull it to level it. This is 10 hours later after we
pour the floor. It's quite strong and nice. You can see this is the bedroom. We're gonna be here
and you can see the septic pipe, drainage pipe, everything's ready. The next step is we need to
water the whole thing and use plastic to cover to edge it. To make it harder, slower, it'll be
stronger, better if we can edge it. That is all about the floor for the second floor. For
the one stories house, it can be the roof if we do one story. But if you want to make second floor,
wait for the next episode. It will be how to start the second floor. That's quite fun and easy. We
can do it ourselves easily like this. If you want to have a book, we have Living with Earth.
It's about how to build earthen house on Amazon too.
