FIRST START in over 20 Years VW Beetle

Screw Driver
87 followers
#machinery #motorbikes #occupations #career
Today we get this 1962 VW Beetle running again after sitting outside more than 20 years in the desert.
Here guys, check out NEXPOW here:😎😎😎
All right guys we pulled this out of west texas last week and it's been sitting in the desert
out there for a long time. I think this is the original engine to the car which is pretty rare.
There is the number 6972448. Check out this sticker right here. The sticker is from 1973 guys.
First thing we're going to do is check the oil. It's a little dirty but it's got oil.
All right last change in 73.
No we don't know. Let's see if it turns over. It's moving so that's a good sign. All right
let's get the battery hooked up. Let's see what happens. Let's see if the radio works.
Oh that knob is crispy. It's bent. No radio. Let's see if we get any lights.
Nothing. Nothing's happening.
All right I disconnected the battery until we figure out what's going on
and I got this switch here. Let's go ahead and replace the key switch.
We got the key switch there. Look at the dust on everything. Wow there's our fuses.
They got something rigged up there too. Look at that. All right gotta figure out where that wire
is going there. It's a red black and white. We need to get the ashtray out of there.
There's a couple little things in there. No key though. Now we can hold it from that little hole
right there. Yeah nothing. No signs of life at all. That's weird. We got some work ahead of us guys.
All right we got it jacked up. Got the tire off here. Gives us a lot better access to the
starter area. Oh there is a huge nest in there. What is that? There's a couple dead spiders in
here too. There was definitely something living in there. Somehow I got to get in there and figure
out what's going on. The starter is back in there. I can already see there's a loose cable here
amongst all the spider webs. There's another loose cable here. I think I found the problem.
There's a giant nest covering the starter. Should we dig our hands in there and just try to figure
it out? Oh yeah. You can see it right there. This cable. This cable was loose. Okay that's on there
now. So if the starter is good it should turn over now. Let's try it. Come on. All right you guys ready?
Oh nothing. Got some serious wiring issues going on. I think what we need to do is drop the engine.
Let's get these cables off here. We got it. All right let's pull it out of there.
That sucker is seized in there guys. Let's see what we got here. All right.
Yeah perfect use for that thing. All right let's get it out of there.
There it is. They had the wrong bolt in there that's why. Supposed to be a little lip on that.
Yeah this thing's got a little rust on it. All right let's keep going. Let's get that engine out
of there. Got some vise grips on there. I think that's working. Yeah there it is. All right we got
that one. There we go. There it is. That worked. All right we're going back under. Right there.
There's one there. Then there's one up in there. You can barely see it underneath the nest. All
right let's turn it. We got another one. Yes. Let's see if we can get on it. Oh yeah. All right.
There we go. We got it. All right let's get this tin out of here. Oh yeah. All right yeah.
These are usually pretty rusty. There we go. Oh the engine moved. Yeah it's loose. There's
nothing holding it. Those two were really tight for some reason.
Man might have to get the vise grips on that one. There we go. It just broke. That one was
not coming out guys. This should come out now. There we go. All right let's get this oil bath
off. That was easy. Oh there we go. Hopefully it's clean in there. Let's see what the carb looks like.
It's a little dirty down in there but not too bad.
Pieces are coming off. The accelerator cable was getting hung up so I just pushed it into the tube.
All right let's try it again. It's moving. It just needs to be lifted up a little bit.
There it goes. It's coming. I think it's coming. It's kicking my butt.
Ah I need to get in shape. I do like using this table though.
Seems like it's working pretty good. She's just been in there a long time.
We're close. Close.
There it is. All right guys there it is. It is separated from the transmission.
You can kind of see it down in there. You can see the flywheel. Will that do it?
Ah table needs to go a little lower. Ah so close. The exhaust is breaking.
There it is. We did it. I want to get back on the table here.
All right guys the engine is out. That's a huge step just getting the engine out. I don't know
what kind of rats they have in Texas but that sucker was big because these are some giant sticks.
Oh yeah they're on there. There we go. You see the bottom's a little crispy.
You can't really see it but there is one hiding down here. There it is. Oh yeah still got some
Texas hay on there. Okay now we can get the yoke on here. We've got some big nuts as spacers to
take up the space on this bolt. All right guys the yoke is on. Nice and solid. Use some nuts to
create a space there and a washer. Same up here. Put a little bit of grease on here.
Yeah we'll have to modify that and make it electric sometime or hydraulic. We're getting
there. A little bit longer. A little bit more. We can lift this up. There we go.
Don't let it slip out. There we go. We got it. It's looking good. It's staying in place too.
It's got a little lube in there to help move around. All right it's on the stand and secure.
Now we need to get a starter on there and I'm going to try to use the starter setup we have
on here. It's a 12 volt but I think it might work. We'll see but we need this adapter anyway.
So let me get this adapter plate off and the starter and we'll try to see if that'll work.
Let's get this Zalix starter kit on here. Engine stand starter adapter. My buddy Tom over there
at Zalix makes these. Pretty cool. Let's get this. Let's get the bottom part on there.
Ground cable on there. All right guys there it is. Check it out. We got the yoke on. We got the
engine start adapter on there. This thing is so cool. It doesn't come with a starter but it's this
yoke. It's this starter ring right here and they have one for the type 1. He's got one for the
Porsches. I've got one on here too. This type 4 and they are awesome and he also has these
switches that we're going to be using so you can turn it on and off and all that stuff. It's pretty
cool. It checks the oil pressure generator. All right guys it's hooked up. We got the battery
hooked up. It's a 12 volt battery going to a 12 volt starter. The only thing I'm not sure about
is that those teeth are going to connect with that flywheel because this is a 6 volt flywheel.
6 volt system but I think we'll be okay just to turn it over. We're going to try it. We ran power
to the oil pressure switch. We'll see if that works. I did not connect the coil yet. I just
want to see if it turns over. We only need the coil if we need to to get spark so we don't need
spark yet. Let's see if it turns over. Let's try it. All right let's see what happens. We don't
really need to hit run but I guess we can. Yeah we just need to turn it over. Oh yeah it works.
It works. That sucker turned over too quick. That's pretty exciting. Let's try it one more time.
There it goes.
All right guys this thing's gonna start as long as the spark
as long as all the spark things work. Went through my stash and found a nice batch of fuel line.
Oh the barb came out. That is what causes car fires in your old Volkswagens. That thing pops
out when you're cruising down the road and fuel just pumps all over the engine and it catches on
fire. So we'll stick it back in there temporarily while we're testing it but we'll end up putting
we'll rebuild this carburetor. I'll put some JB weld on it. I think that's what I did last time.
There it is.
There we go and there's some junk in the line.
Big piece of something right there. See it? Piece of dirt or something. I'll be surprised if this
works. What we'll do is we'll we'll send a little fuel in here and see if it comes out and then
we'll send it to the carburetor. We got all these little sharp objects in our way here trying to
Oh what's that?
Man I should have put a little lube on there first. Those suckers are on there.
That'll probably be fine for now. It's gonna have to come back off.
All right let's see what happens. We're gonna see if any fuel comes out of here.
If the pump's working. Let's see what happens.
Let's get this fuel pump off of here. Got a short 13 and a swivel and it's working.
Getting right down in there. This should just pop out now. There it is. She's a little dry guys.
Look at their little there's a little number on it. Check it out. Made in Canada. So it says
there's a little tag on it. M60175. Interesting. I've not seen that before. Let me know if you
guys have. That's pretty wild. So here is the the one I rebuilt. Made in Germany. I think this would
be more of the one that would belong to this engine. Let's see if that little push rod's
moving first. Yep. That little pin right there moves up and down off the cam
and then it pushes the pump. Pumps the fuel. If you didn't already know that.
All right we should get something squirting out of there pretty quick.
Let's see if we get any spark on the points. All right you can see the points there and
definitely have some dirt on them. All right guys let me know if you see any spark. See it?
You can hear it too. It's six volts. It's a tiny one but we're running 12 volts to the coil. So
coil might not like that too long but it should be all right. Yeah we got spark in there which is
good. All right so what I'm thinking is if we have spark we can put a little fuel in the carburetor
and maybe get that if the engine starts it'll get that pump working harder. Let's see what happens
here. We put a little fuel in the carburetor and maybe we can get this thing to start up.
There we go it's going right into the bowl. All right let's see what happens. Let me stand on
this side away from the spark. Hey it's running. It's sounding pretty good actually. I mean it's
a couple holes in the exhaust but it's running guys that's pretty cool. Let's uh we still got
no fuel. I guess my fuel pump's messed up too huh? I think it just needs a little oomph
somehow. Let's try it again and put a little more fuel in there. All right let's try it again.
All right guys I went ahead and swapped the starter. This is the one that came out of the car.
Might as well try it. Maybe it'll shake itself loose or something. I sprayed some wd-40 on it
and uh that's the one we took out. This is a 12 volt starter. That's a 6 volt starter. We got a
12 volt battery. Let's see what happens. Oh also on this uh starter ring here you have to change
this little adapter. So this is the 12 volt adapter. It's a little smaller so I swapped that
to put the bigger one on there. The kit comes with both of those which is pretty cool.
This one is designed for that. That's the 12 volt one. It's a little smaller.
6 volt is bigger. Let's see what happens. All right guys ready? Oh there it goes.
It's running guys. I still got no fuel for some reason. Yeah hey the starter works.
The starter freaking works. That's awesome. Very cool. I think sounds pretty tough with
the exhaust leaks. All right well it's running. I just can't get any fuel for some reason.
I could have swore this uh this pump would have worked but uh yeah we're not getting any fuel.
Filling up the bowl and out of fuel pretty quick. Now it's pumping. It's pumping now.
It just needed a little extra rpms. Let's see. There we go. It's gonna run now guys.
You ready? Yeah let's make my day. Here we go. One two three go.
Gotta get some fuel in there. My starter's like come on man.
Oh there we go. Gotta get some fuel in there. A little bit. A little bit.
Let's try that. Come on baby. I don't know what the hesitation there is.
We got a loose wire or something. All right. Is the jet squirting? I don't see anything squirting
out of there yet. Yeah I think the carburetor needs to be uh rebuilt. I don't see any fuel
coming out of there. There it goes. Yeah battery's dead now and we're not getting any fuel to the
carburetor. All right well it runs which is pretty cool. We killed the battery and I can't
believe that starter's working. That's impressive. Starter's working. Engine's running. This pump's
working now. Now we just need to get this carburetor swapped out because it's probably
just all gunked up in there and I've got this exact carburetor uh right here. I rebuilt this
last year sometime. This should be the same one. 28 pic dash one. That's it. If we put this on here
it should run in idle pretty good. Let's go ahead and try it. All right I just want to make sure
this pump's still working. Let's try it. Come on. There it goes. Yeah we still got fuel coming out.
Come on. Got fuel there. We should run right away now. Let's try it.
Just needs a little tap. All right guys the battery's dead. I got a jumper. Let's try it.
Let's see. I just picked up this jumper. Next pal. Model X7. I just picked it up. Let's see
if it's got power right out of the box. Hopefully it does. It's got a nice box. Next pal. Model X7
portable car jumper. Jump starter. There it is. Oh yeah. There it is. Let's see if this works.
It's got a nice case. This is pretty cool. I love these things. Oh all right. There it is.
It's got paperwork. It's got adapters for all kinds of different stuff. Charger. So if you need
to charge it, plug it in the wall with this adapter. Hopefully. Yeah. It's got a little power.
Let's see what happens. It's got 71 percent. I don't know if that's going to be enough to jump
it or not. Oh yeah. Fresh. Right out of the box guys. It's got a cool design. Sleek. Steps to
jump start your car. It's got directions on the back which is pretty cool. Let's get this thing
plugged in. This is the adapter for the battery. It comes with flashlights and all kinds of cool
stuff. There's your charging port. Got power out so you could charge your phone or any device that
uses a USB charger and power. Let's see what happens. I'm going to plug it in right here.
Plug it in right here and hopefully, hopefully it works. So this battery is pretty much dead.
Let's see if this will bring it back to life. I wish they would make these cables a little longer.
These cables aren't long enough but it'll work. Let's see what happens. We should have some power
now. All right. Well, that's awesome. The Nexpal worked great. That was really cool. That came in
handy just in time. Well guys, if you need a jump starter Nexpal, I'll leave a link in the description.
Check it out. Use my discount code. This thing's awesome. Still got 68% power and it jumped the
battery and even left some juice in it. So very powerful. Pretty cool and you can use it as a
flashlight. You can use it to charge your phone or any other USB device or USB-C. Very cool. Check it
out guys. Nexpal Model X7 Portable Car Jar Stumper. Portable Car Jump Starter Nexpal Model X7.
This thing's pretty cool. Go check them out. All right guys, it's running. It's running pretty
good. It's first start in 20, 30, 40 years. I don't know. That thing looks like it's been sitting a
long time. We swapped out the carburetor. We swapped out the fuel pump. Although I think the
fuel pump on the other one probably would have worked. We just had to get the RPMs up. But it
looks like it's in pretty good shape. I mean, it's possible they rebuilt it 20, 25 years ago and they
ran it for, you know, a few thousand miles and then it sat for whatever reason. Or they just
didn't use it much. It was just a low mileage car, which is very possible. The thing with this engine
is, even though it's running, the exhaust is blown out. So we need a new exhaust and we need to take
all of these tins off. There could be nest hiding in here underneath the heads or on top of the heads.
We need to go through everything. It's possible that there's a bunch of gunk in the case. So we'll
drain the oil and check all that stuff. I think we'll save that for the next video though. So in
the next video, we'll just start taking this thing apart and seeing what we find out. If we don't have
to open the case, we won't. But if it's been sitting that long, it's possible that it needs
some new gaskets and seals and all that stuff. So it might be a good idea just to open it up and
see how everything looks. If it needs a new cam and lifters, we can put new cam and lifters in it.
We can put an updated exhaust on it so it doesn't restrict the horsepower so much. Possibly put some
bigger pistons and jugs on it so it's got a little more power. And overall, just keep it as stock as
possible but give it some modern upgrades to give a little bit more power. Overall, I'm pretty happy
with that. That's pretty exciting that it runs. And it runs pretty good other than the exhaust
obviously is pretty crusty. So and again, this thing's been sitting in the desert for decades
and you can tell. I mean it's covered in sand, dust, and dirt. There's been critters that have
been in and out of this thing for who knows how long. There could be critter nest inside the fan
housing and clogging up the oil cooler which is underneath here. There could be nest under the
tins here and the oil inside the case. There could be a there could be sludge at the bottom of the
case. So we really should take the whole thing apart, open it all up, clean everything really
good, rebuild it, and that way we got a fresh 40 horse. Hopefully we'll get a few more horses out
of it. We'll change out the exhaust maybe put some bigger pistons and jugs on there and give a little
maybe a bigger cam and lifters. Just a little bit. I want to keep it as stock as possible. The goal
with this car is to keep it as stock as possible but it would be nice to get a little more power
out of this engine. Obviously we have other engines that we can use if we need to. I really
like the idea that this is the original engine as far as I know as far as I can tell. I mean that
engine number right there guys corresponds to the year of that car. It's a 62. Could they have swapped
it out at some point in 62 and put another 62 engine in there? Sure but it's possible that this
is the engine from the factory and it's cool that the original starter was working or the starter
that was in there. We got it working once we got it out of the car and kind of lubed it up a little
bit with some WD-40 and put a little extra juice to it. Put 12 volts to it instead of 6 and it liked
that boy. That thing spins like crazy. When you put 12 volt battery on these 6 volt starters
that thing spins like crazy. It's probably not good for it but I like it. I think it's cool.
Maybe we could keep that combo somehow. I'm not sure how you do that but obviously if you're
running a 12 volt battery through a 6 volt system you're going to blow out your lights,
headlights and taillights and all that stuff. Very excited about this car guys. It is a 1962
VW Beetle. All original as far as I can tell and we are going to go through everything
and make it the best we can. Pretty excited to get the body off the chassis and get the
done. We have brand new pans over here from Wolfsburg West. We're going to get this engine
rebuilt. We're going to rebuild the front end, the rear end, everything. We might not do the
paint right away because that's a whole other project. The car is going to be cleaned up real
nice, driving real sweet so we'll do the best we can. I mean who knows we might start sanding on it
and put a fresh paint job. We'll see. I don't know at this point if it really matters but you know
we could check compression on the spark plugs. We could go through some stuff but considering
how dirty and dusty and everything you know it's going to need to come apart. So next video we're
going to take this thing apart, strip it down to the core, clean everything, put the scat blast
to work, getting all those tins and everything cleaned up ready for some fresh paint. Yeah we're
going to do it guys. It's going to be cool. Also make sure you go check out Nexpal. This battery
jumper is great. You saw how it worked right out of the box so go check them out. Nexpal model x7.
Also go check out Ogree. This is a really cool blower and it's a battery powered handheld blower
guys. Go check it out. Thing is awesome. Very handy. It comes with two batteries, a charger.
Click on the link below. Check it out. It's got lights on it and everything. Very cool.
I'll see you on the next one guys. Later.
