Fuel Injections cleaning in less than 5 Minutes/HOW TO clean throttle body without disassembling

Hello it's Alimek in today's video I'm gonna show you how to clean throttle body without removing and also I will be cleaning fuel injectors without removing as well but I will take them out so you guys can see in real time how the fuel injectors look like when they are clogged and how the fuel injector cleaner effects on them. So few days ago I was driving my car on a road and suddenly vehicle stability control and check engine light came on after I felt misfire and shaking engine So after I got back home I had to use my OBD scanner to know what causes that problem because when vehicle stability control comes on with the check engine light it means there is some serious problem that makes the engine reduce power So after connecting CG solid OBD scanner it will power up the scanner now we can put the key on ignition position Next we gonna press the OBD icon it gonna take some time to scan and the red light comes on when you have a problem with the engine It already tells us that we have one error code let's find out what it is The code is PO303 cylinder number 3 misfire I'm expecting to have clogged fuel injector because I have replaced spark plug before not long ago and the car not that old to have failed ignition coil So I will be using O2L cleaning kit you can use this kit for cleaning fuel injectors, throttle body, intake valves and many more and I will show you how to do the same procedure without using this kit as well because using this kit needs compressed air so not everybody has a compressor at home Here you can fill the canister with cleaner whether if it's fuel injector cleaner or intake cleaner compressed air connected here and you can adjust the pressure with this knob If you have a garage and working on your car just like me definitely worth to buying this kit So the first thing I will do I'm gonna attach this nozzle to the canister hose and it will replace it after mass airflow sensor but not inside the fuel injectors Let's hang the canister under the hood So for the cleaner I will be using seafoam it's safe for throttle body and the fuel injectors Never use harsh cleaner for throttle body like carb cleaner or a choke cleaner otherwise you will damage it and you have to replace it or reprogram it sometimes So I'm gonna be using half of the seafoam for cleaning intake and throttle body and the other half I will save it for cleaning fuel injectors As I mentioned before I will be attaching this nozzle so it sprays cleaner constantly to clean throttle body and the intake valves as well Alright connecting the sharp air I regulate the pressure on 30 psi You can go up to 60 psi as well but I wanna have more cleaning time If you open the lower valve This is how the spraying pattern looks like with the 30 psi It will take about 5 minutes to finish the seafoam Next I'm gonna remove the filter box rubber boots Insert the nozzle and put it back again Make sure to tighten back the clamp otherwise you will have vacuum leak and get more error codes Alright let's start the engine After running the engine for a while and reaching idling temperature I'm gonna open the valve So I'm gonna let the car idle till it finish all the cleaner It will loosen up all the carbon buildup on the nozzle tips So while the engine running on cleaner I will explain how to do the same job without using this kit You can get a seafoam like a spraying can It comes with a long straw Insert the straw after mass air flow sensor and spray with the engine running But with this kit you have more consistent spraying pattern And you don't have to keep your finger for 5 minutes till it finish all the can Okay after finishing all the seafoam I'm gonna close the lower valve Turn off the engine And remove the nozzle And here is how the throttle body looks like compared to how it was before Okay next I'm gonna use this adapter for cleaning fuel injectors There wasn't much room for showing you guys a good angle So that's why I had to remove filter box So it will be obvious where I connected on the fuel rail So what I did here Removed the fuel line and connected cleaner adapter We gonna run the engine with the cleaner instead of fuel And then put the filter box back on the engine Next I'm gonna remove the shop air Depressurize the canister And then filled again with seafoam for cleaning fuel injectors I just pour the other half of the seafoam and connect the shop air again The important part of this procedure We have to disconnect the fuel pump so it doesn't pump fuel back on the engine Because we already removed the fuel line I'm not willing to run the engine with the fuel So I'm gonna disconnect the wire harness before doing this job For most cars you can remove the fuel pump fuse But on Toyota Camry Fuel pump fuse responsible on fuel injector power as well So the engine not gonna run even we are feeding fuel with the canister All right fuel pump fuse back on the engine Now I'm gonna open the lower valve and start the engine We gonna let the engine run with the cleaner till it finished all the cleaner And when the canister about to get empty The engine will start to shake and that's the time to turn off the engine So here is the engine running with the check engine light still on And the fuel pump harness disconnected So how we know the cleaner working and cleans the injectors So I took the injectors out of the engine to see the moment when it cleans the injector So this is just for experiment reason to show you how it will clean it when it's on the engine So I'm gonna start the engine to power off the injectors The car obviously not gonna run But you will be able to see how the faulty injector working And how it gets better after the cleaner comes out and dissolve the carbon So I'm gonna let the engine run with the cleaner till it finished all the seafoam You can do the same procedure without even using this kit You can make a DIY adapter and connect the adapter on a car up cleaner and run the engine with it I have a detailed video about that I will put the video in description box below and YouTube card if you wanna check it out The last thing I'm gonna do I'm gonna zero out one of the chips and drive the car Let's see after how many kilometers It will turn off the engine light without using OBD scanner and erase the code Alright it's been after 56 kilometers Engine light and vehicle stability control turned off without using OBD scanner and erasing the code If you really fix the problem check engine light will turn off after driving for a while Keep in mind you don't have to remove the fuel injectors I just show you how it was before and how it cleaned it Alright that's it for this video Hope the video was helpful and learn something new If it was like and subscribe if you haven't already And I will see you in the next one Bye for now