Lets Fix a Faulty (PSone) PlayStation

Tech Care
3 followers
1 Video View·Feb 15, 2026
In today's video, join me as I attempt to fix this PS1 that has a video output issue.
Recently I bought a bundle of faulty Playstations off of eBay which included
this PS1 which as I mentioned before was listed as having a video fault.
So let's get this plugged in and tested so we can see for ourselves what's actually happening here.
That's all plugged in now so let's get it switched on.
Okay we can hear the sound but there is no video so there is definitely an issue there.
Now that we've confirmed that it is a video fault I've done some googling around and from
looking at similar issues it seems like it might be caused by a faulty capacitor.
So now let's open up the PlayStation to have a closer look at the board and see if we can spot
anything. Okay so to open this up I need to remove these six phillip head screws. This one here is
usually under a void warranty sticker which obviously it looks like someone has voided the
warranty by removing this which isn't always a great sign but I'm going to carry on opening
this up removing the screws and I'm not going to bore you with that process I'll speed it up
and be back when it's done. So now that the screws are out I've just flipped it over and
the first thing I can remove is at the top of the case here and then next I can take out this
laser assembly. So if I just lift this up and then I can remove the cables here and this one
like that and just put that to one side. Then I can take out the RF shield and I can immediately
see it is very grubby I don't know how well the camera is picking it up but there is quite a few
dubious looking hairs everywhere but I'll take this out and put it to the side as well and then
finally I can take the board out and make sure it's unhooked and there we go and now that the
board is removed I'm just going to get my digital microscope out so that we can take a closer look.
So I've just got the board under the microscope here and if I start moving this around we can
immediately see that there is some sort of sticky residue on the board there's quite a bit of hair
sticking to it which would imply that something has leaked. But the capacitors I'm looking for
are these two up here C551 and C550 and they are SMD capacitors so it is kind of tricky to tell
whether they've leaked or not but there is some sticky residue up here and from my research I've
seen that these tend to be the culprit in causing that video issue and location wise on the board
they're both up here here and here next to the video connector so the next step is to get these
removed and to do that I've got everything prepared so I've got my hot air station here
and I've also prepared the board a little bit I've added some aluminium tape just over the plastic
connectors to protect them from the heat and I've also added some kapton tape over the other
components and I have added quite a bit it might be a bit of overkill but I guess it's better to
be safe than sorry. So I've got my hot air station set to 350 degrees and I've added some flux around
the capacitor so I'm just going to heat up the solder and then lift it off. So now that the first
one's off let's get the second capacitor removed. Okay so both of those capacitors have now been
removed I'm pleased to say because honestly I was a bit worried about doing this because I don't have
much experience removing SMD capacitors but it only took about 40 seconds of heat for each one
and they both lifted straight off and now it is time to clean the pads so I've got some solder
wick here and I've also just added a chisel tip to my soldering iron to make it a bit easier.
The pads are now clean I've just wiped them down with some IPA as well as you can see here and the
next step to prepare for the replacement capacitors is to tin the pads so I've got my
soldering iron heated up to 350 degrees and I've also added some flux to the pads as usual so I'm
just going to do that now. So now we can move on to the next step actually soldering the replacement
capacitors to the board. So I have rated my supplies and whilst I couldn't find any SMD
capacitors that match I have managed to find these 220 uf 16 volt through-hole capacitors
that are a good enough match to the four volt 220s that I've removed. But one thing that is
worth checking is the capacitance because I have two different types of capacitors here
I've got some cheap ones and then also some higher quality ones and you can see that the
cheap capacitor is showing up as almost 270 uf and the higher quality one is coming up as 224
which is a lot closer to the 220 uf that they're labeled as so those are the ones that I'm going
to be using today. But before I begin soldering I did just want to mention that I have it given
the board a good clean as you can see in the photo here just using some distilled water and
baking soda to remove the residue left by the leaking capacitors. So to help with the soldering
I've just used a little bit of blue tack to hold the capacitors into place with the negative side
the short leg on the right like it was on the SMD capacitors that I've removed and as usual I've also
added a bit of flux. So I'm going to get these soldered and I'll be back when that's done.
Okay so that's all soldered and I've also just trimmed down the legs and given it a bit of a
clean with some IPA to remove the flux. So now we can give it a test and see if changing them
has fixed any of those video issues. So now it's the moment of truth I'm going to switch it on
and oh it appears to be working. I am kind of shocked about that it seems like just replacing
those capacitors was all it needed and while it is working I'm just going to check there is no
other issues by loading a game. So I'm pleased to say that I've checked it out and the game is
loading fine and the controller works as well as you can see with Resident Evil here.
I will say I am very happy that it all works with just a simple recap and now that I know it works
I've ordered a full set of SMD capacitors so I can recap the whole console and in terms of the
other consoles that came in that bundle I have this PS2 here that has a laser issue and a PS1
that has a power fault. So definitely let me know in the comments if you'd like to see videos of me
repairing those and also any other consoles you'd like to see me try and repair. But that's all for
today I'll see you next time.
