How Britain Made the L1A1 SLR (Archive Film)

Military Rifle History
1 follower
2 Video Views·Feb 10, 2026
Following last week’s look at the very first L1A1 SLR ever produced (1957), we’re sharing a remarkable Royal Small Arms Factory (RSAF) Enfield archive film, shot in the 1960s, showing the key stages of L1A1 manufacture and a rare glimpse of the original Enfield pattern room.
Then we step back and let the film speak for itself, nearly an hour of pure production and engineering process.
0:00 Intro
3:05 Enfield + Pattern Room
3:57 Planning & Tooling
4:37 Rifle body: Heat treat → Machining → Inspection
18:16 Barrels: Drilling, Rifling, Plating & Production line
34:28 Housing/Trigger, Furniture & Magazines
50:16 Assembly → Proofing/Testing → Packing & Dispatch
Hi everyone, Jonathan here with a What Is This Weapon bonus episode essentially,
and it's a doozy. If you watched last week you will have seen this wonderful piece of history,
the first ever L1A1 SLR self-loading rifle ever produced in 1957, and I mentioned that we had
an archive film from the Royal Small Arms Factory at Enfield to show you, filmed in the 1960s
with most of the stages of production of this very thing. Not just the first one, all of them.
Some amazing material in there. A few comments on it I guess. I did notice early on they say that
Enfield started making muskets in 1804, that's actually a mistake, based on some old research
that was current at the time. 1816 is when the factory started in earnest setting up muskets and
other arms, something that had been done at the Tower of London previously, so that's where the
two sort of overlap and responsibility moves over. And in 1823 they start making their first
scratch-built firearm, the Baker pattern of 1823, which we've shown you before in sealed pattern
form. So a little bit of a gaffe there. The other thing I wanted to comment on is some great,
if brief, footage of the original pattern room at Enfield. So we are now effectively the pattern
room, we acquired that collection in 2005 along with the archive that this film came from, and
you get to see the original incarnation, the original wooden racks. We still have some wooden
racks in this collection, in this store, some of which are original at least to the Nottingham
pattern room. So you're seeing the original version set up, well in the early 19th century,
changed its role and remit a bit over the years, became more of a sort of reference museum
collection. Originally it was for governing manufacture of British military weapons,
and they make a mention there of a whole rack dedicated to the iconic weapons made at Enfield.
I think they mentioned 10 rifles. We haven't had a rack of Enfield weapons like that specifically
for a very long time, and if we did it now we'd probably have to include the SA80,
so I'll let you argue in the comments about whether we would include the SA80 in that.
But lovely to see that. It sort of bookends the footage, and then the rest of it is
the various manufacturing stages with some great in-camera effects showing you how
things were actually done, different machining processes, heat treatment and all of that. So
the technologically and engineering and similar inclined amongst you are going to love it.
The historians, scholars and students of history are going to love it as well.
So I'm going to shut up now and let you watch the whole thing, just under an hour, so please enjoy.
The Royal Small Arms Factory at Enfield has been associated with small arms
since 1804, when the factory was used for the assembly of arms.
By 1855, actual manufacturing processes had been introduced.
The canal was for a long time the main means of transport,
barges bringing in raw materials and taking away finished arms.
In the pattern room is located one of the foremost collections of small arms in the country.
The last rack holds the 10 rifle designs which were manufactured in quantity at Enfield.
The film illustrates some of the methods used in present-day manufacture of an automatic rifle,
the L1A1. After being fully tested and accepted by the services,
the planning department prepared manufacturing layouts for quantity production.
Tools, fixtures and gauges required for producing each of the 157 components
were designed by the drawing office and manufactured in the factory tool and gauge rooms.
The rifle body is given as an example of a planned layout.
The body starts as a forging at the ROF Woolwich and is then sent to Enfield where it is first
heat treated. Loaded in batches of 250, they're heated to a temperature of 860 degrees centigrade
and are allowed to soak at this temperature for three hours.
One man controls the process. Temperature time charts are plotted automatically for each load.
On removal from the furnace, the bodies are quenched in oil and they remain submerged
for 30 minutes, in which time their temperature is reduced to 100 degrees centigrade.
The components are then tempered at 650 degrees centigrade and allowed to cool. Here a load of
3,000 kilograms is loaded via a 10 millimeter diameter ball onto the surface for 15 seconds.
The diameter of indentation is then related to a Brinell hardness number.
The forging is first machined to create datum faces by duplex milling its sides.
This is followed by plow grinding and final sizing to close tolerance by surface grinding.
Surface broaching replaces many milling operations in quantity production.
The five broaching operations, of which three are shown, replaced 15 milling operations.
One body is machined at a time. The cutting speed for all operations is 10 feet per minute.
The surface machined is shown by the dotted line. Two bodies are machined at a time. The last six
teeth on a broach bar are sizing teeth, giving accuracy and the required surface finish.
Three bodies are machined at a time. The loading and clamping of the components is simplified
by good fixture design. The labor on the production lines is semi-skilled. A skilled
machine setter sets the machines and checks each machine periodically. One setter controls the work
of four to six operators. The operator loads and unloads a series of machines. In this way,
the cut time of the machine cycle is turned to productive advantage. The magazine opening is
roughed out for further machining. A special purpose machine for automatic drilling, reaming,
and tapping of the barrel and gas tube holes. The tools work simultaneously on four different
bodies. The work table indexing to the next position at the end of each cycle. There are
six stations on the rotating table, two being the loading and unloading stations. The pneumatic
gauging of 11 features at four settings. The tolerance for each dimension is marked on the
individual tubes. The deep hole drilling technique adapted for drilling the pin axis and shoulder
locking holes. The horizontal broaching of the ejector block seating using four broach bars.
The cutting speed is 12 feet per minute. Profile milling of the sand cuts from a master template.
An example of the adaptation of the cutter to the workpiece. Another example of the
utilisation of semi-skilled labour. One operator tending a group of machines.
The operator inspects one component in ten. Machining the bullet leads. This difficult
operation has been simplified by good tool and fixture design. The adaptation of an optical
projector for the inspection of a feature which is difficult to measure by mechanical means.
The tolerance band being shown on the screen. The fixture is designed to inspect both bullet
leads by moving it from one location point to another. The rotary milling of the front end of
the body. The body in its fixture is loaded into the machine. The cutter begins to machine the body.
This automatic miller creates the required form on two bodies at one setting. This shows the form
milled. Catch is milled. The slotting of catch clearances. The duplex milling of the housing
slots is an awkward operation overcome by good planning. Ten feet per minute and slows to five
feet per minute. This part of the broach bar roughs the slot so. This one the intermediate
roughing as shown. The middle broach finishes the slot to drawing dimensions. The local hardening
of the bullet leads by induction heating. The coil is a hollow copper tube through which cooling.
Heat is induced in the body by eddy currents. The ejector block is assembled to the body
and drilled as an assembly on a twin spindled drill. Then riveted together. Each body is finally
inspected and an acceptance mark stamped on each accepted component. The barrel has been forged
and heat treated. A testing phase has also been produced. The automatic indication of the hardness
of the material and whether it be acceptable or not. That is 270 to 310 diamond pyramid number.
The barrels move into a machine shop which specializes in barrel production. A barrel
is faced and centered. The depth of center being checked to ensure the accuracy of following
operations. A steady band is machined. The breech end is rough copy turned on a copying lathe
and then gauged. The muzzle end is copy turned to give the male center required for deep hole
drilling. The barrel is deep hole drilled revolving at 4,500 revs per minute. The tool feed being two
and a half inches per minute. Oil is pumped through the tool at 1,000 pounds per square inch
to cool the bit and remove the swarf. Each barrel is checked at this stage for cracks
by the use of ultraviolet rays. This is an example of a cracked barrel. The fine boring of barrel,
a very old technique but an essential one, removes one and a half to two and a half thou
from the bore. This operation is repeated at a later stage. Barrel straightening. This is the
shadow seen by the operator and the extremes of bent barrels are shown by the dotted lines.
The straightened bore is used as a datum for all succeeding operations.
Barrels are straightened twice during manufacture. The locating cones at muzzle and breech ends
are remachined true to the bore. The outside diameters are turned concentric with the bore.
The six rifling grooves are cut on these machines. A cut being set and the six grooves cut in
rotation. This is repeated until the required depth of rifling is attained. Swarf is removed
from the cutter box by rotating brushes. The breech end is ground to 0.959 inches diameter
for thread rolling. The major diameter of thread rolled is 1.00 inches. A flat is created at a
certain position from the start of thread for assembly purposes. A pneumatic gauge which
gauges six diameters at a time. Thread grinding, a method of producing accurate threads to close
tolerances. An automatic lathe rough machines the rifle chamber and feeds two operators who
finish machine the chambers using nine special chambering tools. The chrome plating of barrel
chambers. Six barrels are loaded on a jig which holds the short lead anodes. Controlled plating
ensures a constant thickness of chrome. That is a minimum of 0.001 inches is given by a current
of six amps and barrel voltage of three and three quarter volts for 90 minutes. All traces of acid
are removed by rinsing. The final sizing of barrel bores by lapping. A new method of barrel production
which was devised and planned at Enfield. It's an automatic line of machines designed to replace
the present method. The forgings are fed into the line automatically faced and coned then transferred
by conveyor to the next machine. A barrel is automatically unloaded and loaded into the machine.
A steady band is machined. Two tools then simultaneously copy turn the outside diameters
of the barrel. The steady band is remachined to correct any deviation caused by the preceding
operation. The cold forging method. The forging is shorter and larger in diameter. A larger hole is
drilled in it to accommodate the splined mandrel. The barrel material is hammered around the mandrel
the bore thus being finished and rifled at the same time. A blank is rough machined and centered
in preparation for deep hole drilling and other operations. This drilling machine was designed
and developed at Enfield. The drill speed is 8,000 revolutions per minute and the feed one and three
quarters of an inch per minute. The hole drilled is one eighth of an inch diameter and three and
a half inches deep. The firing pin hole is reamed and counterbored on a capstan lathe.
The block breach is a typical example of a broached component. Three components are machined
at a time. The block breach before and after broached first. A multi spindle drill attachment
drilling and reaming the retainer hole. Four components are machined at a time.
Note the ease with which loading and clamping is affected. The cutting speed is 12 feet per minute
slowing to six feet per minute. Three components are machined at one time. Two components are
machined at a time. The removal of a broach bar from a machine showing the location on the machine
table. Typical examples of broach bars built up of segments. The segments being classified for
sharpening. Broached sharpening. The form of the cutter teeth can be easily seen. Profile milling
of cam faces from a master template. An example of good fixture design in the milling of further
cam faces. Gaging the cam faces using a special gauge. The carrier breach block is produced in
a similar manner that is mainly broaching. On all presses shown guards have been removed
for filming purposes only. A 70 tonne power press is used to blank the housing. The plate thickness
being 0.098 inches. The first forming operation. Formation of the tang angle. Blanking of the stem
hole and trigger guard slots. Various milling operations machining clearances and slots.
The inspection of the milling operations. The assembly of the sleeve pistol grip to the housing.
The block housing is assembled. The rivet holes are drilled. The rivets are spot welded.
Spline milling of clearances. An automatic drilling machine. Nine holes are drilled and
tapped on this machine. The drilling jigs are double-sided being turned over for subsequent
machining. The inspection of the holes so formed. Form of milling of a radius. Mortise milling the
notches for safe, single and repeat. The assembly of the recoil spring tube to the housing. The tool
implied is a special torque spanner. Many small screws and rivets are required for the rifle
assembly. These and other small components are produced on automatic lathes. The example shown
is the firing pin. The deep hole drilling of the butt blank is similar to the barrel technique
but compressed air is used as a coolant and swarf remover. Slitting the slots for the insert.
The inserts are cross-grained to the butt grain to strengthen the front end. The automatic machining
of the rear end of the butt. There are eight working stations and one loading station which
controls the rotation by means of a trip switch. Forming for butt plate. Note the speed of the
cutter. At this station we have two synchronized heads. One comes up at an angle. It completes its
work and retracts. The other head then moves in horizontally. Machining the profile for butt
plate. Inspecting of the profile formed. The automatic machining of the front end of the butt.
There are five working stations and one loading station. The butt is roughed to shape on a band
saw. This machine automatically machines eight butts simultaneously from a master form which may
be seen in the foreground. Note the ease of loading of components. The butts are soaked in
linseed oil for 20 minutes. The hand guards and pistol grip are also produced in the stocking
shop. The guards were removed from the presses for filming purposes only. The magazine is blanked out
on a 70 tonne power press. Note the economy of strip width. The plate thickness is 0.031 inches.
Form the ribs. Forming for seam first. Forming for seam second. The first folding operation.
Forming of the seam first. Forming of the seam second. The final folding and staking of the seam.
Removal of the mandrel using pneumatic cylinders. The seam is then gas brazed. The gas brazing of
the lug. At this stage milling operations are carried out on the magazine lugs. Spot welding
of the guide plate to the case magazine. This is a special purpose machine developed and built at
Enfield for the production of the magazine spring. Smaller components for the magazine
are produced on a high speed dyeing press. The slow motion sequence shows the action of the press.
This type of machine replaces 11 conventional press tools on the component being manufactured
which is the platform magazine. Burrs and sharp edges are removed by the barrelling process.
Ceramic chips, abrasive and water being tumbled with the components. The separation of the chips
and components. The magazines after being degreased are phosphated by immersion in a
phosphating bath for 30 minutes. They are then rinsed and paint sprayed. A load of bodies,
barrels and magazines being loaded into a stoving oven. The assembly of the magazine
and components. The assembly shop and its conveyorized system. The position of the
start of thread is marked on the barrel. The assembly of the eliminator flash to the barrel
and its riveting. The body rifle is assembled to the barrel. The alignment of foresight to the body
is checked. Constant torque breaching is used to check the final breaching of body and barrel.
The shoulder locking is an example of selective assembly. The gauge indicates the size required.
There are 16 sizes of shoulder locking. The inspection of headspace using high and low
block breach assembly and high and low dummy rounds. The housing trigger mechanism is an
intricate assembly involving many small parts. The housing trigger mechanism being assembled
to the butt. The firing pin is inserted into the block breach. The assembly of the extractor to
block breach. The alignment of rear and foresight is checked on this fixture. The rifle is now fully
assembled and is ready for government inspection. Barrels are proofed using a proof round. The
pressure being one and a quarter times that of a normal round. The rifle bore is inspected after
proofing. The testing of the breach action and the stamping of the proof mark. All rifles are
tested for functioning at an elevation angle of 80 degrees and a depression angle of 80 degrees.
The sights are finally adjusted and the rifle undergoes an accuracy test at the 100 foot range.
The rifles are dipped in oil and drained. Three protective layers are used in packing.
Wax paper, PVC sheeting, and wax dipping. The rifles are packed in boxes for dispatch to the
armed forces. The rifle L1A1 joins the other Enfield produced rifles in the pattern room.
Meanwhile, research continues for the development of new small arms.
