I BOUGHT MY DAD A FLOOD DAMAGED ASTON MARTIN DBX

Ex Used Car
15 followers
64 Video Views·Feb 9, 2026
I just bought my dad this Aston Martin DBX with a catch.
This car was fully submerged underwater, which meant it was cheap and that's because after
it went underwater, the car never ran again.
Now we have no idea how deep this car went underwater and how long it was in the water
for, but sometimes taking a risk on these flood damaged cars can really pay off.
Let's just hope this one does.
Here it is.
My dad does not have a clue and this is his actual dream car.
This is like hitting the jackpot for my dad.
This DBX has been going on about these since the dawn of day innit.
Best thing, it was this car that he'd seen.
This was like the first DBX he'd ever seen.
It was.
Now I don't know if you can remember, but when we went to Copart to have a look at the
Rolls Royce Cullinan, which was also a flooded car, next to it was the Aston Martin DBX and
my dad fell in love with it.
Come on then, let's go and have a look at my favourite one.
On the way here, he said if I was going to get any 4x4, it would be this one.
Now these DBXs have a four litre twin turbo V8, but if it's sucked up any water whilst
it's been running, it's likely the engine could be toast.
If it's only five grand, I'm bidding.
You're going to have a go on this one Tony.
It ain't going to go for what I want to bid.
Now whilst we were at Copart, the guys let us put a jumper pack on it and attempt to
try and start it.
Yeah, look at that, all the electrics work.
2,000 miles.
Do you know if I had a car that had done 2,000 miles, I definitely wouldn't be driving it
through a flood.
But no matter what we did, this car wouldn't start.
Might just need a rod.
Yeah, it might.
Or a new block, if it's been sitting in there, rusting.
But one thing's for sure, my dad truly found his dream car that day.
You can dream.
So, I bought it.
Right, so this is listed at Copart as does not run or drive or start.
And somebody's been here before molesting it, because these are not supposed to be off.
Oh yeah, look, it goes straight into the turbo.
The turbos are directly underneath there, but what's worrying is that's really high
up.
That is really high up.
So if they've gone in the water, they've had to come up here.
But, we have seen a lot of videos of people going through like Rufford Ford and that,
sending it and then, yeah.
I think people think the faster you go through water, the better it is, when it's not necessarily
the case.
So if it goes in the turbos, the worst thing with a turbo car, water will go in, it propels
the water down and into the engine, which is actually not ideal.
And then once it goes inside the engine and the piston tries to compress the water, piston
versus water, piston loses every single time.
The conrod just goes, see you later.
But we're hoping that's not going to be the case.
When water gets into the cylinder, or on this diagram, coolant, when the piston comes up
on that compression stroke, it obviously can't compress the water, which as I mentioned,
then can cause damage to the conrod, even the crankshaft and even worse cases, the actual
block.
If that's the case, then it's an engine rebuild and this engine looks really complicated.
But sometimes you can get lucky.
If only a little bit of water have got into the cylinder, the engine can pump it out after
just running for a while.
But if the car doesn't run, sometimes you can just remove the spark plugs, turn the
engine over and the pistons will push out the water through the spark plug holes.
At the minute, we lost in Monaco, are we going to win here?
We can only hope the risk pays off.
As an extra surprise as well, I got him personal reg plates, MA, Matt Armstrong, 23, the reg
of the car, dad.
I don't think he's even going to notice that, but we'll see.
Now let's wait for him to arrive.
We covered the car over and plans to show him the next day.
We're starting a new car and it's in the ramp.
Have you got any guesses on what the new car is?
Is it a new car I don't know about?
Yeah.
It's a new car you don't know about?
Right.
Any guesses?
Oh no.
If you had to drive one other car but the Ferrari, what brand car would you drive?
Aston.
Yeah.
And also, if you had to drive one other car but the Ferrari, what other car would you
drive?
Like what type of Aston?
A DBX.
DBX.
Yeah.
Okay.
What do you reckon to do with that?
No, you're having me on.
It's a DBX.
Unwrap it then.
Unwrap it.
This is yours.
Hey, you might be surprised.
It's these moments that made working on cars in a restaurant car park and on the driveway
truly worth it.
And without all of your support, none of this would have happened.
And if you want to be a part of the journey, then now's a great time to subscribe.
What's wrong with it then?
Nothing.
What are you doing?
It's yours.
No, it's not.
It is.
It's your car.
That is yours.
Look inside.
It's your car.
Has it been in a river?
What's wrong with it?
There's got to be something wrong with it.
There's got to be a cat.
Why would there be a cat?
Start it.
Let's hear it.
Why would there be a cat?
Let's hear it.
Does it start?
Try and start it up.
Key's up here.
Why have you got me this?
Because you wanted one.
Do you not recognise it?
Is this the one?
This ain't the one.
This is his mate.
This is McLennan's mate.
Is this the same one?
Yeah, this is that one.
Oh my God.
We've had it all that time.
I had it all that time.
We've hid it from you for months.
Oh my God.
This has done like no miles, hasn't it?
No, it ain't done anything.
This is the water thing in the engine, isn't it?
It's been flooded, yeah.
Well, I think that couldn't have gone down any better.
We've finally got my dad his dream car.
It's a turbo.
Some kind of weird...
Oh, I can't believe that you bought this.
I knew you'd be buzzing with it.
Oh my days.
It's well nice, isn't it?
But he's not going to be able to drive it until we work out what exactly is wrong with it.
Apple CarPlay.
Oh, thanks for getting me this.
This is brilliant.
You might want to have a look back here.
What's going on?
Just opened the boot.
Oh, no.
Oh, okay.
Oh, someone's already been in.
Oh, no.
The engine's coming out.
Oh, no.
Inside this bag was a box of spark plugs and coil packs.
So our theory that we might be able to pull the spark plugs out, turn the engine over and pump the water out seems to have gone down the drain.
Because it looks like someone might have already tried it.
Somebody's already taken the spark plugs.
That's one job done, at least.
Yeah, but that now means that we've got to pull the engine and rebuild the whole thing.
Yeah, we need to find out what's gone wrong with it.
Let's get started then.
First off is this strut brace which is covering over the engine cover.
Once we get that off, we can remove the engine cover to access the engine, which somebody's already touched.
Look at this.
Coil packs.
Just pressing in.
There was a few more coil packs in place which hadn't been removed, so I'm going to pull them out as well.
First one.
And now we should be able to get a camera and see what's going on inside the cylinder.
Oh, look. Is that the bore there?
That looks sludgy.
I don't think that's meant to look like that.
Engine very bad in cylinder seven.
Do you know what? It don't really matter what the others are like.
No, I think we've got to take the engine out.
We've only put the camera down one cylinder and we can already see there's rust in the bores.
And it was nearly the same for every single cylinder.
And if there's rust in the bores, then for sure this engine isn't going to run right.
When that piston goes up the bore, it's just going to scratch the whole side of the cylinder,
allowing oil, fuel and compression to get past the piston.
Right, goal is drain all the fluids.
We've got to get the engine out.
I don't think that it's gone in.
If there's loads of water in that oil, we should be definitely draining the gearbox oil as well.
I think it's only splashed up.
That's my fear. I think it's gone into a Ford.
What do you think?
Could be right.
It only takes a tiny bit of water to seize an engine.
But if loads have got sucked up, then possibly it could have got in the oil as well.
Ready?
And we're about to find out if it did.
Oh, that's very bad.
That's not good.
I've never seen it that bad.
Okay, that is milky.
I think we need to do the gearbox as well.
Oh my, that's chocolate milkshake.
Well, I wasn't expecting that.
It's not looking good.
Now time for the oil filter.
I know for it to be in there as well, it's wrong with it in.
Oh yeah, it would have, yeah.
So water has got in the engine oil and a lot of it.
So the likely chance that this engine is not saveable is pretty high now.
But what about the gearbox?
Looks good.
Yes.
Get in there.
Good news for us, the gearbox seems all okay.
The oil in there seems nice and clear.
So at the minute, it only seems like the engine has been affected by the water.
Let's get it out.
First thing to come off is the exhaust.
Again, full of water.
I've removed the left side and my dad's removed the right hand side.
Now that the front part of the exhaust's out, we can move on to the next part.
Exhaust off.
Now the prop shaft, which is connecting the gearbox all the way to the rear differential at the back.
Once that's disconnected, that will allow us to bring this whole thing down.
There's about four bolts holding the prop shaft to the gearbox.
I'm holding the wheels at the back to stop the prop shaft from spinning
and then my dad's removing the bolts at the front.
Then we can slide that out of the gearbox.
Next thing, the steering rack connecting to the steering column.
My dad's undone the bolt on the steering column and then pulling it away from the rack
because the rack's going to come down with the subframe of the engine once all of the other work's done.
Got to remove both wheels.
And my dad's going to start by removing the arch lining
because this job's going to be made much easier if we can get the front bumper off.
That way I can see all the hoses at the front that need to be removed as well.
The brake calipers we're going to take off and hang on the car.
That way we don't have to re-bleed the brakes and lose any brake fluid when we remove the engine as well.
And now I'm working away at getting the front bumper off.
Now I can clearly see what needs to be removed.
There's some wiring which is bolted to the chassis of the car.
That's going to come down with the engine.
And parts of the suspension is going to come down with the engine as well.
My dad's removing the bolt for the stuff which is going to come down with the engine.
Like the wheel hub and all the lower control arms.
Next up I'm going to disconnect all the hoses which are going to the radiator at the front of the car.
Because the radiator at the front of the car will be staying on the car.
But the hoses are going to the engine.
Which is what we're trying to remove.
More hoses which are going to the front are the oil cooler hoses.
These are leading from the engine to the cooler at the front and they've also got to be removed.
What are you doing Tony?
I'm going to de-gas.
There's of course the air con condenser as well.
But we've got to remove the gas before we remove those lines.
Coolant's out, oil's out, next up fuel.
And finally the fuel lines which lead to the engine from the fuel tank at the back of the car.
I'm removing them from the engine and then the engine should be completely free from the car.
Air con gas recovered.
With the air con gas out we can now remove the air con lines.
And it's time for us to go back in the air.
All the fluids are all out.
Next step, our plan is to lower the whole thing down as one.
Subframe, engine, gearbox.
And to do that we've got to undo these big bolts up here.
Here, here, here and here and here and here.
And a few up there and a few up there.
Oh my god there's loads and there's a few up there.
And this whole thing's going to lower down and hopefully have it on the floor.
Then we've got to separate the engine from the gearbox after that.
So let's do the first ones at the back.
All subframe bolts are undone.
Axle stands are underneath to hold the subframe, the gearbox and the engine.
We're hopefully now going to lift the car up and the engine stay in place.
But we think there might be a few more hoses connected.
But we'll find out now which ones are connected because they'll be hanging on for dear life when we start lifting them up.
Let's go.
This is a delicate process.
And unfortunately we did manage to break something.
The steering column just dragged on the side of the engine as it was coming out.
And managed to break part of the plastic on the inlet manifold.
But once we got that out of the way, the engine was out.
Yeah!
Only one perishment, just this inlet manifold here.
Because the steering rack here pulled on this and broke.
But now we have the big 4 litre twin turbo V8 out of the car.
And now we need to find out what we need to replace in order for this car to work.
But to do so, we need to remove the gearbox on the engine first.
So my dad's undoing all the bolts which connect the gearbox to the engine.
And then once they're undone, we're going to separate it from it.
And that's job done there.
We can see the flywheel and the torque converter still on the gearbox.
Now, time to strip this engine down.
We need to see how far this water damage has got.
First off, the two turbos off the top.
Then, the charge coolers.
Right, this is all stripped down now to a point where we can start getting the cylinder heads off.
But we actually haven't even tried to turn this over by hand.
So we're going to see if it does turn over by hand, that's one good sign.
But we think because of the amount of rust in the cylinders, it might scrape up the cylinders.
But we think the cylinders are dead anyway from what's happened with the Porsche.
Let's see if it turns over.
I think we might need to purchase a new bar if we're doing this.
That's fully stuck.
Yeah, rod's got to be bent.
Bent rod.
Got to be bent.
That engine is well and truly seized.
And our suspicions is that it's got a bent conrod.
But we're not going to be able to confirm that until we access the conrods.
But first, we're going to try and see what's going on with the top of the engine by getting the cylinder heads off.
And to access the cylinder head bolts, we've got to remove the camshaft.
If you don't know what all these parts do just yet, don't worry.
We'll explain it when we start putting this thing back together.
But now, with those camshafts out, I can access the cylinder head bolts.
I've got to remove all of these bolts and then we should be able to lift it off and check the damage of the knee.
That is rusty, McGee.
Oh, there's a hole. Is that a hole in it?
It's rusted.
It's eight away at the cylinder.
There's literally a lip there.
These cylinders need to be super smooth.
And the water's sat in there for so long, it's actually rusted away part of the cylinder.
That is a creme brulee. Oh my, look at that.
That's gone. That's finished.
But it's likely this might be cheaper than a Porsche block.
It's like, because this is an old engine, it's been out for a while.
And it's not like a performance engine.
Well, it is to an extent, but not like.
Can we get a block?
Let's build up a reconditioned block.
We can have a look.
With the cylinders looking like that, it's for sure we're going to need a new engine block.
And the other side was no different.
That's a cave.
The GT4S engine went fully underwater, like actually underwater.
And it was actually in better condition than that.
Yeah, because you know why? The water can run out of the piston.
Oh yeah, because it persists.
Whereas on this, it gets trapped.
Yeah, it sits up like that.
Best thing they could have done, when they got this engine in the water,
flipped it upside down.
Would have drained it all out.
And then you'd just replace it in a rod.
So for the viewers at home, if they drive into a flood, what do you advise?
Go home and hang your car to drive upside down.
That probably would have saved this engine to an extent.
We still think there's a bent conrod,
which is why this engine isn't turning over.
But the fact that all the cylinders are all rusted up,
means we're going to have to replace the block anyway.
Now we're lifting the engine off the subframe,
so we can get it on an engine stand to turn it upside down,
and see what damage is caused underneath of it.
Outdoor play!
And as it's nice weather, we're going for outdoor play, as I like to call it.
Front diff outdoor play.
Is it hard?
Because it's 4WD, it actually mounts the front differential to the engine block.
And part of the driveshaft actually travels through the sump.
And remove that, then I can take the flywheel off,
take this casing off here,
and then we should be able to lift the sump off the bottom of the engine.
With the sump off, we then remove this oil pickup part,
and underneath, we can see the conrods.
Which one's bent? Oh, I found it!
I see it.
Oh yeah, that one.
And our suspicions were correct.
One of the conrods were bent.
This is because it's tried to compress water.
Now, if I remove this conrod and piston,
I should hope the engine will be able to turn over after that.
Oh, there we go!
Oh, look at the rings.
Well, that's what happens when a conrod fights with water.
This has tried to go up, like that.
Water's been here, can't squash it down.
Conrod's gone.
Look at all the rings.
That's how the water's got into the engine, isn't it?
It's gone past the rings down into the oil.
A lot of water went past that, didn't it?
Yeah, that is MC rusty.
So the worst case scenario has become the worst case scenario.
To get this engine working,
we're going to need a new conrod, a new engine block,
and all the parts to rebuild it.
And once that bent conrod was out,
the engine actually turns over.
But you can see the state of the cylinders here,
covered in rust,
which would mean if we built this engine back up like that,
you would see loads of smoke coming out of the exhaust
from oil blow-by down the cylinders.
And even though this DVX has become a worst case scenario,
I still think we can get this repaired under budget.
Here's our list, which we think we need.
Conrod, engine block, inlet manifold, gasket and seal set,
timing chain set, 8 piston rings, 5 gold rings,
red locks, oil filter, bearings, dip oil, gearbox, crank seal.
This is the deal maker.
We don't know how much all of this is going to cost.
I don't know.
Because I was hoping it was going to take the spark plugs out
and it was just going to go out, stop.
We don't know.
But what we do know is a second-hand engine on eBay.
We don't do very well with second-hand engines.
We've had a history with that.
It is £12,999, second-hand.
The cost of the car was £82,000.
So that would bring the total bill altogether,
if we bought a second-hand engine, to £94,999.
Which actually still isn't bad.
When you look at the used prices of the DBX 707s,
you're looking at £130,000 upwards.
But I think we'd save more money,
and it'd be better if we just rebuilt the engine that we've got.
But then I found that wasn't possible.
So they will sell the internals, but they don't sell the block?
Yeah, correct.
Okay, so they'll sell everything like piston rings,
conrods, all that type of stuff?
Yeah, no, he didn't come back to me and say,
oh, these are not available.
He just saw on there that you put a cylinder block.
We can't get that.
Aston Martin will sell us all the parts we need to rebuild the engine,
but won't actually sell us the cylinder block.
They don't offer it separately.
But they do offer the complete engine.
New engine from Aston Martin, £64,000.
Which is just crazy.
Now we have the option to get our cylinder block repaired,
which would mean re-boring the cylinders,
which would then cause a chain reaction effect
that would have to modify all the rest of the parts in the engine to make it work,
which I don't think is worth the risk here.
So then I looked at second-hand engine, £12,999.
But that's actually for an Aston Martin Vantage engine,
or a C63 engine,
or there's not actually no DBX engine second-hand listed.
The engine in the DBX is a Mercedes-AMG M177 engine.
And that engine is used in loads of Mercedes as well as Aston Martins.
The only difference between the Aston Martin Vantage and the Aston Martin DBX,
four-wheel drive and rear-wheel drive.
And because the DBX is four-wheel drive,
it has that hole going through the sump at the bottom of the engine
that a driveshaft goes through.
So if you look at the actual numbers on the side,
it's a 177950, which is...
We've got a 177950.
So I think they use the same block,
but there's small variants in it.
So if we choose to go with the second-hand Aston Martin Vantage engine,
then we may have to switch over a few components.
But then I think I found a solution.
This is our solution.
We're not...
We're not 100%.
This is a Mercedes GLC engine, I believe.
Second-hand.
We've just got our fingers crossed.
Now, the Mercedes GLC is four-wheel drive,
so it does have the hole in the bottom of the sump for that front differential.
But the issue is the GLC has 612 horsepower,
whereas the Aston Martin DBX has 697 horsepower.
Yeah, you're good.
Yeah, yeah.
AMG gang!
Our theory here is the reason it has less horsepower but the same engine code
has got to be to do with the externals of the engine,
like your turbos and your intercoolers and the tuning of the car,
rather than the actual engine.
So in theory, all we need to do is transfer all the external stuff off the DBX engine
and add it to the GLC engine.
And if it doesn't work, at least we can send it back as one whole piece,
whereas if we split apart an engine, a second-hand engine,
and put that sump on it and it doesn't work,
then they're going to say, well, you can't send it back because you molested it.
But the good news out of all this, this was £7,300,
which if we do fix it for this, it will be good.
And it saves us having to build a whole engine.
We've just got to really hope the engine's good.
We'll change the spark plugs, we'll change the oil, change the oil filter.
It's so hard to know, and this is one of these things with engines,
we ain't going to know until we build it all together and get it in the car.
So we started taking off all the ancillaries of the GLC engine,
like the turbos and the charge coolers.
But as we started taking more off, we started to notice more differences.
This has not gone well.
Oh, no.
Not well at all.
Well, as far as we know, just so far, the cylinder head is completely different.
The camshafts are completely different.
I think the front pulley's all right.
Our only hope at the minute is that the block's the same,
because if that ain't the same, then we're really, really in a problem.
First thing we noticed was that, look, this hole here.
We noticed, oh, well, there's a hole there, and it doesn't have a hole there.
Next thing, picked up these ones.
What are these things?
So much to do with the cams.
Oh, no.
So took this off, looked at that one.
So look at these two compared like that.
Massively different.
Completely different.
Okay.
Maybe there's a chance it's the same underneath the cover.
Camshafts, look at them.
These are like little peewee boys.
See that?
Quite small, little thin things.
Look at them.
Look how complex that is.
Look at that.
They've got guides in them.
The absolute tanks of camshafts.
So the cylinder heads, along with the camshafts, are different on the DBX engine.
It looks like to get that extra power, they've increased the size of them
and added some kind of variable valve timing.
Our only hope now is that the cylinder block with all the pistons and the crank
are the same as the DBX.
We've got to get this cylinder head off,
and then we're hoping to see that on the underneath.
And if we don't see that on the underneath,
really, really, all we needed was the block.
That's all we needed.
So if we paid 7.5 grand for a block, which is cheaper than Aston Martin anyway,
but if that block ain't the same, we have well and truly done ourselves.
Okay, this is the big moment now,
whether we just wasted £7,300 on this engine,
because as soon as I take this off, we can't really send it back.
He's going to watch the video as well.
So I've taken the cylinder head off.
Once you loosen these bolts out, that's it then.
The bolts are finished.
You're meant to buy new bolts.
You're meant to have a head gasket.
And all we're hoping for now is that we pay £7,300 for a good cylinder block with pistons,
and it is the same as that cylinder block, minus all the rust in it.
We're about to find out.
It means we've got to build off the engine.
First off, loosen the chain.
Now, if this works, we might have a good DBX at the end.
Well, my dad might have a good DBX at the end,
because before I bought it, I did check it out on Carvertical,
and it did say that the mileage was all checked out, all good.
It's only done like 2,400 miles.
It's got no outstanding finance, which is good.
It does show up that it's a Category N, which is quite usual for flood-damaged cars.
The Rolls-Royce Cullinan is a Category N as well.
So that means non-structural damage.
So you have Category N and Category S.
S is structural, N is non-structural.
And when it's flood-damaged, it just goes in the non-structural category.
So that will always show up on the Carvertical report.
And quite interestingly, it's had four owners, but that's including myself.
And I can see as well what registration plates they had on.
They had some bougie registration plates.
66PN was one reg, and then 1AFF,
which is now on a Ferrari 296.
Sometimes as well, if your car was damaged,
it's likely to show you photos of the car when it was auctioned off at the Carcass auction site.
Now with the camshaft removed, we can see how different they actually are.
But once we remove these head bolts to remove the cylinder heads,
I'm hoping we see exactly the same as what we've seen on the DBX engine,
but without the damage.
So these have pins, look, like actual pins.
Which hold in the chain guides.
I don't know why they do it like that.
It stops people messing about with engines they don't know how to battle.
Now, the moment of truth.
Off comes the cylinder head of the GLC engine.
Is it the same?
It's different.
No.
It's different.
It's different?
It's different.
What do you mean it's different?
The pistons are different.
You're joking.
The pistons are domed.
Well, you should check your car out on Carvertical
by clicking the link in the description box below
and using code MATT for discount
because then something like this is less likely to happen to you.
Yeah, it's different.
The block might be the same, but the pistons are different.
How far are we going to keep going back until we just have to buy a new engine?
What are we going to do?
We can use the pistons off that engine.
Yeah, but that's what we keep going.
Yeah.
Oh, the crank's different.
Yeah, I know.
The block's the same, so we can use the original crank.
Look at that piston, yeah?
Just visual.
Right, it's flat.
Four indents here for where the valves sit.
Okay, let's go on to this one.
This is like an indent
and these valve dents are way more prominent in this than they are in that.
So it's completely different.
So when people say, oh, it's got the same engine as an AMG GT, a DB12,
an Aston Martin DX, Advantage, whatever, they ain't the same.
They may look the same, but they ain't the same really, are they?
What are those head gaskets saying?
They're saying they're the same.
Head gaskets are the same, pistons are different.
That means the block's the same, so we could change the pistons.
What about the crank?
Well, we'll find out.
What do we do at this point here?
We've got to keep going.
We didn't spend seven grand and get this far to stop now.
We have to keep going.
Do you think the ring's off these pistons?
I know it sounds a bit bodgy.
Oh my, no, come on.
Behave.
This car is beating us.
Our only hope now is that the engine block's the same as the DBX,
and maybe, just maybe, the conrods are the same.
But once we got the sump off, we could see the conrods of the DBX ending 007,
and the ones on the GLC, 005.
So even they're different.
Isn't it different?
They're all 05s.
There's no way we're going to take this piston off and put it on a 005 rod
and think, that'll be good.
The block might be the same.
We've still got the block.
Now our hopes diminish to just the cylinder block.
So everything is coming out of this GLC engine.
Even Kevin was defeated.
Out comes the pistons with the conrods,
and I am going to mark these up just in case for whatever reason
we need to put it back together.
But it was clear to see that the conrods and the pistons were different in the GLC.
It's strange a manufacturer would make something which looks so similar,
but then the small, minute changes makes that increase in power.
And now, out comes the crankshaft,
which leaves us with one GLC block.
Now, good news, good news.
We have a cylinder block, which I think...
No, no, no.
We're going to say, I know is the same as that.
The piston's out of that.
This piston here.
These do go and fit into there.
Nice there.
The piston.
So we can use this block.
So we've not completely wasted our time or money.
We just spent maybe a little bit over the odds for a new block.
People are probably going to ask, yeah, you can probably get this block repaired,
but when you get it repaired, you'd have to have it bored out,
and it just becomes an ever-going nightmare of chain reaction of things
that once you get that repaired,
everything else has to be to spec of the new block that you have repaired.
So at least we've got an OEM block here.
But all of this mess over here was not planned.
And I thought we was going to be able to repair this DBX within a week
and get it for my dad.
But it just doesn't always go to plan.
So it looks like we're building a complete Mercedes DBX engine
with no experience in doing so.
But we're not going to manage to do it in this video.
But thanks so much for watching this one.
Before you go, the new merch is now out,
and you can grab it with the link in the description box below.
But thanks so much for watching this video.
If you enjoyed it, hit the subscribe button, hit that thumbs-up button,
and I'll see you in the next video where we've got to build this engine up.
Peace out.
She said that I can come and do some outdoor play for a bit,
but I've got to wear my gloves, she said.
