1969 CHEV WAGON - Blown Methanol Build

RetroCarz
284 followers
So another episode on the 69 Chev wagon build guys. I've had this car for literally five years now
and it's going to be a blown methanol skid car. It's pretty awesome. In the last episode we did
put some hectic paint on there. It was hectic paint but it was also a hectic paint job because
they didn't fix any of the dents. And in this episode we start looking at the rear end doing
the falling and setting up the diff to hold some power and keep this thing together on the burnout
It's a freaking Monday and Sam's on sugar. The keto diet went really well guys.
It did well for me. I feel good. I feel great. So I'm back on the sugar. All right.
I got a little bit excited over the weekend. I didn't film anything but my axles have arrived.
These beautiful shafts. Strange Performance Racing and Engineering of the US of A. I got these
through VPW. They are a reseller, distributor, whatever you want to call it. So custom sizing,
whatever spline you want, whatever lengths you want, whatever bearings you want and it attaches
to the new Ford big style housing. So now the mission is to get this welded properly onto the
diff. So as mentioned earlier, we've shortened this diff. So it's a Ford nine inch. Cut it down.
Now we have the axles. We can confirm that all that sizing is going to work.
I've gone ahead and assembled all the brake assembly. So big shout out to Wilwood. They've
on board with this build. As I mentioned on the front, big brakes, big heavy car with a bit of
power. On the rear, we've just gone for their drag set up. So it's still four pot calipers
and just their standard disc brakes. So that's all assembled. I wanted to make sure that I got
the dimensions right and it's bang on because all these measurements and offsets for the caliper
had to be calculated into the custom axle design. So happy with that. So that's what I'm going to
do now. Throw the minimum appropriate center in, axles in and just slowly weld it up and hopefully
it stays true. So you've got to get those spaces really square. So I don't even know how I'm going
to do that, but I think putting it into the center or at least lock this end of the axle in
and then all we've got to worry about is keeping this side good. So that's what we're doing today.
I literally measured this so many times, like heaps of time from different spots
to ensure that these are straight. I was stressing.
Oh my, this is one of those jobs that you measure 400 times and tack and then measure 400 times
again because I'm a tight arse. There are places out there who can do the straightening and
weld it properly, but as long as you let it cool properly and don't let it heat up,
it shouldn't warp too much. So it's tack, measure, weld a bit, measure, weld a bit again,
measure and if it's wrong, you're probably too late to fix it again and you just keep welding.
It's not like me to take so much care with something like this, but with expensive parts
from America and bits and pieces that I took a long time to find, I definitely took my time
with this to make sure it was correct. All right, I've gone ahead and pretty much
assembled the whole diff. I didn't film much of this, but from the bench scene when
Josh helped me put that center together, I've just thrown the axles in,
made sure they fit, mocked up all the brakes and just dropped the center in with a couple of bolts
because I wanted it sitting under the car to make sure our fitment worked well. So looking at side
here, we've got a pretty nice tuck. I'm going to roll the guards a little bit and pretty happy
with where that's sitting. Now, here's an interesting thing. When you make a control arm,
we did the same with this with, I think it was the XC or something. When you're using
high arms, you actually go down to your local Bunnings or your Mitre 10, grab some PVC pipe
because it's plastic and just push the ends in. You can actually measure out
all your arms to get it all mocked up before you go and weld it out of steel.
So I'm pretty happy with where this is sitting. I've measured the center of each of these arms,
so I've got adjustment out and adjustment in so I can actually change the holes to get
the different parallels. So once they come to alignment, if I figure out the car's squatting
or lifting too much, I can change how parallel those bars are to fix all the anti-squat.
So I'm going to measure these now and as my good friend once said, Juju, we're going to get some
chromoly. Chromoly, we got this from Racetech, I think it was. So I haven't welded chromoly before,
but I spoke to some guys at a weld shop and they gave me some bloody EK580SD2 filler rod. Apparently
you can use that with chromoly and just weld it as if you were doing stainless with the same
tip and everything. So I'm going to cut these now out of the same measurements that we got
with the PVC and weld these ends on and then this is the panhard. So this is the last
little piece of the puzzle that I need to figure out. I'm going to do the arms first and then
somewhere in here, you essentially put a panhard that comes across the bottom of the diff there.
So I need to make sure there's clearance for the drive shaft ring that's got to go in and also make
sure there's room for adjustment across here. So once that panhard's in, then it's pretty much
five links and set in place and we can move on. So that's what I'm doing at the moment.
That's right, back on the TIG welder today, I was actually super lucky that the PVC pipe I got
fit perfectly. So it made it really easy to get the exact lengths I needed to cut the chromoly.
Pretty much TIG'd it in like normal TIG welding, it's just a slightly different filler rod and I
preheated before I welded to make sure it had proper penetration and didn't weaken that chromoly
when it was cooled down.
All right, the chromoly is welded under here and we're going to start looking at this panhard.
We're a bit far away there aren't ya? Times like these where it's handy to have a plasma cutter
because what I'm going to do is basically cut some new brackets that come off this bar here
and then weld a couple of misalignment spaces and a bolt straight through here. So with the plasma,
I can draw it up on Fusion, 3D CAD it and then send that to the plasma cutter and that'll cut
that out of the 4mm or whatever the bloody hell I'm using on the table and yeah, just makes it a
lot easier to kind of trial and error some stuff, cut a couple of different pieces. First thing,
got to make out a cardboard, that's the first step of CAD, Cardboard Assisted Design and then we go
to the computer and hope to get this bar in and then we can start moving it up and down to find
how much kind of ride height movement we've got and whether or not I can bag the thing or I have
Okay, sorry guys, my camera went flat but we did get it all put in.
Alrighty guys, so to get down to that bracket, we're just going to remove a couple of these
things. Let's get into it. Okay, now that that's out of the way, we can access this bracket down
here. Now all you want to do is get it. Sorry guys, my camera went flat there but I just went
ahead and continued pulling it apart. You should be down to about this stage now. This is sort of
the finished product here. So the panhard is in, all of these have been fully welded and I've got
sitting on its own weight here. So I pretty much just welded these bars in here to hold the level
and I found the right height that I want. So this is where it's going to sit. I mean, bagging it
is an option but right here, I can pretty much get coil overs off this bar here, straight down
off some tabs there. That's pretty much how most of these four links work, just a couple of coil
overs for now and if I can bag it later and get something in here, we can do that too. But for
now, I'm just going to leave the body and the car just sitting on the ground as it is and I'm going
to start working on something new and that is the tailgate because it's the only bit of rust that I
pretty much found in this thing. So I actually haven't done sheet metal work to this extent
before, so you're going to learn with me but this is a very rare car and you can't just go and buy
a new part. So you're going to have to repair things. When things are rusty like this, you have to
basically make do with what you've got and that's what I need to do in this situation because the
wagon is pretty good condition apart from this tailgate. So we're going to have a crack at
repairing it and it's pretty damn rusty. It actually took me a long time to get this off the car
because the bolts were a pain in the arse. We found a snake in here who scared the ---- out of me
because it gave me a little test whip. Nearly died but we're here. So like I said, I am no panel beater
and I am no professional when it comes to doing stuff like this. So I'm going to, to the best of my
ability, figure out how to do this. So first things first, I'm going to strip it down while I can,
try and get this brace out. Whatever this rod is, it's a little tensioner, I don't even know.
The thing about this tailgate, it drops down and opens like a tailgate but it also opens like a
door. So it opens in two directions which makes it a little bit more complex than other doors. But
from what I can see, there's a little seam join along here. I'm going to hit it with a grinder,
cut this section out, cut along the bottom and basically cut out the rust. And with that section,
then I can inspect it closer and see what it was constructed of, whether we need certain mounts
and stuff in there. And then we can either use a flat sheet and a bender or cut something out on
the plasma and basically start welding it back in. So it's sort of structural. I'll need some fairly
decent thickness material but look, first things first, let's cut this rust out and see what we're
working with. Look, it's never a fun feeling cutting into a car from the 60s but it had to be
done. This was pretty much irreparable. We have to put a new piece in.
Alrighty, I've moved outside to make this mess, which is probably a smart idea. So I've done the
first run along here and this panel's already lifted off, which is easy. So that looks like
a bit of an outer skin. So we'll remove that instead of cutting all the way through
and wrecking something that may be all right. No, it's pretty fucked.
So we'll continue to cut down that lower section. So there's like an inner and outer skin.
And then we'll start cutting along the bottom. So I'm not really sure, I'll show you,
I'm not really sure where I'm going to cut along this line, like through the middle here,
a lot of that interior bits rusted out. But like along here, you could probably get away with just
like treating that with some rust converter. But we'll probably cut along this ridge line here
and then we're going to have to play with this little fold because a bit of drama there. But
all of this is absolutely toast. So we'll get rid of that. This is that first skin we got rid of,
which revealed, yeah, a few more dramas behind here. It hasn't rusted all the way through,
but it's probably just worth replacing that whole panel there because
a lot of water has been sitting there and it's probably rusting from the inside. So
more cutting to go. I've got pretty much everything cut out and I found a little
bit more rust down this corner here, which I've kind of dug into. I might take a little bit more
out first, but I found some of this rust converter. So I'm going to try that before we go any further.
So essentially I read the instructions with this. You basically brush it on. So I had an old
toothbrush, brush on the converter and let it sit for about half an hour. And then you clean it
back with a cloth. And then you come through with a second coat with some like methylated spirits
to clean off any residue. And then that acts as like a barrier for any future rust to occur. And
then we'll just bomb it with some rust converter black, chassis black, to try and protect it from
the future. So I've just put that on parts where it's like more structural and there's some pretty
heavy surface rust there, but it hasn't rusted through anything. And that's sort of where the
door hinges onto the rest of the body. So we'll treat that while I can get in there. In the
meantime, I'm letting that set. I'll start making up a couple of panels. I'll just do some measurements
and we'll start with a plate on there, put one bend in it to meet here. Then there'll be a few
extra corners we've got to fill in later, but at least we'll get this main panel bent up and I'll
use slightly thicker material that was on there. It looks like it was about two or three mil. So
maybe we'll use some four mil just to give it a little bit more body and it should last a lot
longer. So let's get into it. Alright, a big shout out to Ryan from Lifetime Trailers. I just plasma
cut a piece of metal and ran down to his to get it bent up. My bender will not do how wide this is,
but I ended up having to plasma cut it because this bottom section of the door actually curves
down a bit. So it's not a dead straight line. So I had to put in a bit of a bend there and it fits
pretty good. So I've gone for a thicker material. This is, I think it's about four mil. So it should
be nice and strong. So I'm going to go around and stitch weld across the top here, throw a few
welds in the bottom, and then it's pretty much repaired this bottom section. Then there's just
a couple of little squares here, which we'll cover up with some thinner metal. And then it's just,
whatever's going on back here, there's another hole of rust, but that's a tomorrow problem.
Let's get this on. Okay, look, this definitely hasn't turned out to be one of the prettiest
repair jobs I've ever done, but it's functional. And for a car like this, it literally just needs
to be strong. Doesn't really need to look that great. So call it a success. Holy smokes. All
right. I've come up with the sickest idea just then. Oh, by the way, this is all in good luck.
She ain't going nowhere. I've done the test. I've said the words, it's strong as. But the drama with
this backside, like I don't even want to go through and fix this. The car's already painted. So
I came up with a sick idea. Hopefully it's going to be different. Wish it will be. Good,
questionable. But what I'm going to do, it's got multiple reasons. For a bit of weight saving,
I'm going to cut this whole skin off and just remove that piece of steel. We don't need that
anymore. Deleting all these lights, tail lights, they're going somewhere else. What I'm going to do
is rivet in a new piece of sheet metal to curb it here, mount it, and then I'm going to wrap it
in custom sticker built like a street sign that says slippery when wet. And then a picture of a
sliding everywhere because it's a skid car. Get it? And if I'm like drifting on the back,
it's like people would follow it. You know what I mean? Like following you,
slippery when wet. Sick, right? I don't know. I think it's pretty cool. So the whole tailgate's
going to be a custom road sign. Pretty much just lay a piece of vinyl on here and make this custom
sticker. It's going to look good. So what I did is I headed down to my friends at AJ Steel to grab
some half mil thick gal steel. This is really thin so it's super bendable and then pretty much
just cut it up to match the section of sheet and then pop riveted it on. Okay, so the steel is on
to flatten the thing out and we got some road sign yellow. Well, kind of. It's not exactly,
but it's yellow. Get the idea? Now, my sticker guy Dan said you must spray lots of water on this
and squeegee it out. It doesn't lift up like normal wrap. It's basically a big sticker.
So we're not going to do that. We're just going to put it on without water because I can't be
fucked. And the amount of bubbles and bits and pieces probably suit the rest of the car anyway.
So I just want to get it done. Let's go. Yeah, look, I gave it two seconds of thought and then
went, look, I better do the right thing. So I ended up giving in and spraying it on with some
proper dishwashing liquid to try and get it to stick. Glad I did because I ended up trying a
bit later that didn't have any water and it was horrible. So many little bubbles and stuff. The
thing was just turning out to be an absolute mess. Oh, some days you have a good day on the tools
and other days are just an epic fail. And today is one of those epic fails. So even though I gave
in and put the water on, it's just still a million bubbles. Number one, actually, what I want to do
is probably paint this white first because it's actually quite transparent. Having a white base,
it'll make it pop a bit better. It's just you can sort of see the dull grey behind it. And then I
tried this little bit at the end. We didn't quite have enough, which is also an annoying thing. I
want to change that. You can see that join there. And then without wetting it. Yeah, Dan was right.
You get a ton of like just crinkled up bits that you can't get out. So I'm not going to put this
on until I fix this. But this is the idea here. We've got a slippery when wet sign. So I might
actually try and get some proper reflective road sign tape and then probably take the tailgate down
to Dan. And he can just do it properly. So yeah, what a shame. I'm a little bit annoyed about this.
So we're going to wrap the episode up there and I'll have to reconvene and figure it out later.
Catch us later.
