Our hyperadobe earthbag bond beam prep continues with custom forms built in-place on our circular walls. Going to therapy is a sign of strength, not weakness. BetterHelp makes therapy simple, with 10% off your first month to help you get started: https://betterhelp.com/tinyshinyhome (Sponsored by BetterHelp)
SECTIONS // 00:00 - Good Morning! 00:23 - Special Gueset 2:09 - Marking Wall Heights Laser Level 4:35 - BetterHelp 6:34 - Inner I-Beam Install 10:20 - Locking in I-Beam 10:51 - Friends are Here! 12:13 - Building First Bond Beam Forms 15:21 - Kittens + Fiona 16:37 - Finishing Forms on Living Room Circle 17:37 - Starting Forms on Bedroom Wall & Sketchy Scaffolds 21:29 - Spring Events 21:51 - Production Ramps Up 23:06 - The Process So Far 24:49 - Finishing Bedroom Circle Forms 30:08 - Marking Bar Joist Plates 31:06 - The Inner Circle 33:38 - We Have a Problem 35:25 - Coming Up...
Good morning.
Just sitting here at the airport waiting for the arrival of our special guest so that we
can get to the next part of this house build.
There we are.
That plane was completely full.
Yeah?
Yeah.
Well, you made it.
So of course as soon as I pick my dad up, we're at the hardware store.
So we have a big project coming up.
There's a few more things I need to get that I wasn't able to get before he got here.
So let's go get everything we need.
Thankfully, I have a saw so that we can cut up all the wood that we need to get and put
it in this little tiny Prius.
It looks a lot bigger.
Yeah.
Let's go down this way.
Looks crazy from here.
Yeah.
Because you can see clear into the inner wall.
Yeah.
A little bit taller.
Yeah.
Quite a bit taller.
The last time I was here, I could just not see over.
So you were probably down in here.
What do you think?
I think it's huge.
It just looks tall.
Remember, we're not on the floor level.
So seven more inches.
A lot of dirt.
Pretty solid up there?
Yeah.
So solid.
A whole lot of dirt.
Yes it is.
Once my dad was here, we wasted no time getting started.
We found our zero point for the floor level, did a whole bunch of calculations for the
roof pitch, and began marking the bags where the forms would attach to the walls.
These marks had to be on both sides of all circle walls.
It took us a while, but we finally got it done.
Then it was time to make some jigs to make the form work easier.
Make this.
That'll be a 5 16th clearance hole right there.
This will be cut off to where it'll be right at the bottom of that all thread.
And that way we can slide that down over your 3 1⁄4 inch wall until this hits the bag,
and then we can drill our hole.
So it's pretty slow going.
We're basically marking on either side of the wall, all the circle walls, exactly where
the bottom forms should be.
We're kind of using that as a leveled zero point.
Anyway, it's a long story.
There's a lot of math involved.
Ashley's dad did a lot of it.
So I'm kind of over here by myself just marking the wall.
All by myself.
All by yourself?
Really?
All by yourself?
Yeah.
Where have you been?
Welding.
Welding what?
The tool to bend the plywood.
Oh, fun times.
Okay, well, I'm going to keep doing this.
You go weld your toys.
Working out all the calculations and marking on all the bags took all of day one.
Now we're very eager to get these forms started.
Oh my goodness.
Would you like a level?
It's been a long day.
A long day of climbing up and down scaffoldings.
Yeah, are we done?
Yeah, we did it.
It's all marked.
Good job, babe.
With the new year off to a busy and slightly stressful start, I'm happy to report that
BetterHelp is today's video sponsor.
And if you've been here a while, you've heard me talk a little bit about my therapy
journey that started a little bit over a year ago.
I personally can't think of a better way to start 2026 than to take care of yourself and
your mental health.
If you're new here and haven't heard me talk about BetterHelp, BetterHelp is an online
therapy service.
When you go to their website, you just answer a few simple questions and they're going to
match you with a professional therapist, usually within 48 hours.
If you're like me and worry about being comfortable with somebody new, especially when you're
sharing so much personal information, don't worry.
If you aren't feeling confident with the therapist given to you, you can change therapist at
any time for no additional cost.
Therapy has been essential for me in this phase of life.
I am trying to parent teens and young adults.
I am trying to run a business, a homestead, be a good wife, be a good mom, be a good friend,
be a good sister, a daughter.
There's just a lot on my plate right now, as there is with everyone.
So it's really nice to know that I can reach out to my therapist and chat about any issues
that have come up during the week.
And BetterHelp makes it easy.
As long as you have an internet connection, you can do your therapy session.
I've done my therapy sessions from my bed, from my truck, running errands in town.
Having someone to talk to is essential, and I highly recommend you give BetterHelp a try.
Don't wait until it's too late.
Let's start the year off right.
Visit betterhelp.com slash tinyshinyhome and save 10% off your first month of therapy.
You will not regret it.
Just don't wait.
Now, let's get back to building those forms.
Welcome to day two of constructing a bond beam on a roundhouse.
We're up early so we can get started before our friends arrive to help.
There's a lot of tools to haul back and forth, a lot of scaffolding to disassemble and reassemble.
But this morning is all about prepping to install this massive I-beam, which will connect
to the rebar and essentially join the inner circle together to make it even stronger.
First we need to cut the ends of the rebar on the inner circle.
Cut the beam down to size and get it ready to lift up 12 feet in the air.
Our neighbor and friend Mark down the road is going to bring his tractor over here and
we're going to lift the I-beam up in place.
We've already cut it to size.
We're going to try to get it over towards the wall so it's just a little bit easier
for Mark, but it's like 300 pounds, so we'll see how this goes.
Now you shouldn't be doing this, right?
Now I'm going to be careful.
Just pull it straight out.
Keep going.
Take it over here?
No, just keep going.
Okay, hold it.
Now can you pick it up and put it over at the top?
Somebody needs to hold the wheelbarrow still.
You guys get each side?
Yeah, and we're going to slide it until the weight's balanced on it.
Hold it.
It's got to come more your way.
Let it down now.
Can I jump in front?
No, I think we're about right.
Let's go with it.
Okay.
Easy.
Jonathan, move yours over more.
So how are we going to set it?
Just right straight in.
Keep going.
Right there.
Okay.
Let it go.
See if it's steady.
If we want to, we need to have a piece of wood or something we can put underneath it
so we can get the strap around it.
Right here is the center.
That center?
Okay.
Put that down.
All right.
How is it?
There's no way.
What did you say?
Are you serious?
It's in the middle?
We still cannot believe that once this beam was set in place, it was perfectly level
and there was no need to shim up any of the sides.
Next, we just needed to drill four holes on each side
and put in some all-thread to connect to our existing rebar.
We're making sure to overlap the rebar as much as possible.
I think we get about two feet here.
Jonathan made sure to tighten those connections as much as he could,
bent all the all-thread to follow the curve of the wall,
and now we're ready for our friends to arrive to help on the next step.
We've already figured all the elevation from the top to the bottom wall
and each wall, and we've gone around and marked on each side of the wall
where the bottom of the forms go.
So if we just stay with that, we'll have plenty of room on our forms.
The concrete's not going to come to the top of the form,
but we'll put in our inserts where it needs to be,
and the concrete's going to be roughly eight inches thick.
There's one wall where it's an inch and three-quarter deeper
and one where it's three-eighths of an inch shallower than eight inches.
We ended up with a slightly steeper pitch roof
because we built this inner one up too high.
I don't know what happened, but we overfilled.
So instead of leaving it at 112 and making the bomb beams taller,
we went to a 1.10825 or something like that.
I just took the bottom wall and the top wall and the distance and divided it out,
and everything came out pretty close.
We just got on a roll.
And I'm not going to tell anybody.
We just told everybody.
First up, we're cutting down all the all-thread into 18-inch pieces.
This gives us enough room to attach the three-quarter-inch plywood,
the washers and the nuts on either side of the forms,
and we'll pull the forms together as they sit on top of the back.
Man, look how easy they go together underneath.
I know, right?
Jonathan, we want to just let the end stick out beyond the wall a little bit,
and then we'll put a piece in.
You want to go up in this direction.
Okay.
Right through that, then.
I'm on the line now.
My line is...
Okay, hold on, down a little.
There's the line, right there.
Okay, I'm holding it.
All right, is that good?
That needs to be plumb. Is it plumb?
Okay, go ahead.
Whoa.
Am I coming in right about the back?
Yeah, I don't like doing it when somebody else is holding it,
because I've slipped off and drilled into my thumb.
Yeah, I've got a mark right there.
You should be screwing as far out on the piece as you can.
Well, I can't reach it, and I'm not left-handed.
You're going to need to put six screws in there, not three.
Torx drivers!
I don't even see a line anymore.
We're all sucked in.
The first day of learning a new skill
always takes so much time to get into the groove.
We're trying to figure out the best process,
the right amount of tools,
tricks for holding the boards in the right position,
and just working together on something
that needs to be pretty precise.
Thankfully, we have a great team here,
and we all work really well together.
Adelaide and Steve are working on getting the all-thread prepared
with washers and nuts
so that it's easier to put through one side.
Once the boards were pulled together,
we measured the space at the bottom
so that my dad could cut a 2x4 to the same measurement
to be installed at the top of these boards,
holding them together at the same distance.
This is very important.
And of course, we can't forget Cloud,
who is always right by our side,
making sure the job is always done right.
It was a long first day,
but we really got into the groove,
and we figured out some good tips
to make it easier on us for tomorrow.
And of course, there was plenty of time
to play with kittens after.
Go in!
Oh my goodness, that's adorable.
She pops, just pops out.
Is this Warbler?
Good morning, friends.
We are out working on the bond beam build this morning again.
We actually got a lot done yesterday.
We only started at like 1 in the afternoon.
We got almost all of this big outer wall finished.
But because we decided to build these weird, fiddly,
I call them the wings,
these sections of wall that come off
near the front door and near the back door,
and they just go into nothing.
And so we have some plans to reinforce that.
But part of this is we have to build something custom
here at the end of this form,
so that when we pour the concrete in,
it obviously doesn't like all come out.
So we'll work on that this morning
before we have some other people get here,
because we really need a lot of hands
to build those forms together.
So anyway, that's what we're doing this morning.
Wish us luck.
Well, sorry, guys.
I know we had a camera set up to show this process,
but we can't find the footage anywhere.
Hopefully we'll get some shots of what it looks like after.
But hey, look, our friends showed up again.
We didn't scare them off.
Thanks for showing up, guys.
Don't kick it with your bad foot.
Dick, can you go down just a little?
I'll be below the mark.
Okay, that's fine.
Is it tight now?
The seam could come further in,
but whatever makes more sense.
I'm not holding it.
You're not?
No.
Oh, I thought you had the wood on.
I do, but there's no pressure on it.
Are we on the line?
No, you're a little low.
Then just push it up.
Where do you put it on the line?
Right there.
Don't worry, Cloud.
Grandpa isn't mad.
He just talks like that sometimes.
I promise everyone is okay over here.
The only thing that we may need to worry about
is the scaffolding falling over.
This is not OSHA approved, but that's okay.
We do what we can with what we have.
Clear!
It didn't move.
Careful, careful.
Is that a good spot?
Should I go back a little more?
No, keep it.
All right, ready?
This tool that my dad made out of spare fencing parts
has really come in handy on this outer circle.
Being able to hold both boards in place while drilling
and putting in the all-thread was a huge help.
Thanks to our friend Tom for showing up today
and helping us out.
And thanks Trona for being cute in that sand pile.
Now we're really moving.
Do you have your...
Nope.
Day two of putting up the forms went so much faster
now that we're finding our groove.
Everyone knows the process and what comes next,
so no one is waiting on boards or tools.
It's beautiful to see all your planning and preparation
kick into high gear.
And of course, Fiona and Scarlett got plenty of time
to play with the kittens.
We got a lot of rain that night,
and the next morning was wet, rainy, foggy.
But to stay on schedule,
we have to work through the rain and the wet.
Because it will certainly sink.
So, will you stand on this side over here,
just real quick, see if it's sinking,
because we might have to put a little piece.
Yeah, you're going to need a piece under there too.
Fourteen and five-eighths.
Hey friends, future Jonathan here.
Just a quick reminder,
we have a couple of events coming up this spring.
We have the Hyper Adobe Safety and Design 101
on February 28th through March 1st.
We have Mean Green Homestead Tour on March 28th.
And we have the Lava Creek Utility Lodge Workshop
April 6th through 11th.
You can sign up for all of them
at tinyshinyhome.com slash events.
Let's get back to it.
Morning friends.
We're a couple of days into building our bond beam forms.
As you can see,
we've decided to take on another large project.
But it's good,
because it means we can get the bond beam poured,
and then that way that's all ready
for when we want to start doing the roof.
And we're trying to get this done
before it gets too cold to actually pour the concrete.
So the basic idea is that we're
taking these strips of plywood
we've already marked on each side of the wall
where the exact level the bottom of those boards should be
based on a bunch of math that Ashley's dad did.
And then we're sticking all threads through
and we're tightening it up
and then we measure that distance on the bag
and put in a two-by-four at the top
and then cinch it all together.
We do that about every two feet.
It's definitely like a really fiddly process.
It takes about four people,
two people on each side of the wall.
And there's like a bunch of tools and like different...
It takes a long time.
There's a lot of different steps.
But yeah, it's going pretty good.
We finished this big wall.
We're about to finish the big bedroom wall.
And then we just have the two inner circles.
The bond beam is only going on the circle walls,
just in case anyone's confused about that.
We donate it on the straight walls
because that's not what's going to be supporting
these bar joists that we're going to put up later.
So yeah, we've got three, four more days
before the concrete and the pump truck show up.
So we got to get to it.
You're having all kinds of problems.
What did you do now?
Well, first my legs hurt and now my arm.
What did you do?
I don't know.
I just started running
and then my legs just started hurting.
I don't know.
And now my arm's hurting.
Sam, I am.
The tape measure is right there.
Not my fault.
He's blaming the wife.
He's blaming the cutter.
Like a glove.
Did you expect anything less?
Well, it's been a wet, rainy, soggy day.
But we did manage to get
the big outside bedroom wall all finished.
We got it capped off
and we even installed some of our rebar
for another project that we'll deal with later.
But basically this wall
and the other one that sort of stick out here
and aren't really supported,
we're going to be supporting them.
So we're tying rebar into the bond beam.
It's coming down and then we'll tie it into more rebar
and build a form and pour something later.
That's a story for another day.
Yeah, we had to close down early today
because of the weather.
Where'd you get that drink?
Dollar Store.
But it was half.
I only drank half of it
and I just dumped the other half out.
Should we go to the Dollar Store?
Sure.
It's a we need a drink kind of day.
Anyway, we're wrapping it up.
We've got Friday, Saturday, and Sunday to finish.
We have the inner circle, the hallway circle,
and then we have to set all of the points
for where the actual bar joists are going to go.
It's going to be tight.
The views this morning were incredible.
So much fog from yesterday's rain
made the mornings nothing short of magical.
Jonathan and I were out early
trying to get the walls marked
for where the bar joist plates
will eventually be installed.
We're trying to get as much done as we can
before help arrives
so that we can hopefully stay on schedule.
We thought a week was enough time to set up these forms,
but it was at this point
that we started second-guessing our timeline.
But at least the sun is out and the sky is blue.
It's going to be a good day.
That's good to me.
Okay.
I think that's the last one.
Oh, yeah?
We just have to go on the outside
and mark those, finish marking those.
All ready.
Ready when you are.
Now it's time for the inner circle.
We switched from 3 1⁄4-inch plywood to 1⁄2-inch.
Everyone told us that we had to use 3 1⁄4-inch
for any form work,
but there was no way to bend that size of plywood
into this tight circle.
So with 1⁄2-inch plywood cut to size,
we just had to use our special tool we made
to help hold those boards in place.
Steve also had a really great idea
to pre-stress the plywood with his ratchet straps,
and that helped so much.
Thank you, Steve.
Well, here we are at 418,
and we're still working on the inner circle
that we started working on this morning.
So some things that we are learning.
Our curve is very tight.
It's a very tight circle,
so we have switched from 3 1⁄4-inch
that we used on the outside walls
to 1⁄2-inch,
and it's still cracking some of the boards
if we push them too tight.
So what we're having to do is put those
all-thread rods in closer together
and just go slower around the circle.
It's very complicated,
very tedious,
very time-consuming,
and we're all wondering why we built a circle house.
But this is okay.
Everything's going to be fine.
But that means we only have Saturday and Sunday
to finish the hallway circle
and to set all the 2 by 8s
at the correct pitch
for the trusses to sit on
that the concrete is going to be poured up to.
Very complicated again.
So we're just fingers crossed
that we get this done in time.
Okay.
Perfect.
So we got a text early this morning
from Ash's dad,
and he said,
we need to talk,
which is never a good text to get.
So he came over, it was still dark out,
and he was like,
I don't think we're going to be ready
for the pour on Monday.
After all the trouble with the inner circle yesterday,
our timeline is all messed up.
We still have to finish the inner circle,
do the hallway circle,
and then we have to set all 40-something plates
on pitch and at the right height
throughout all of that.
And he just really didn't want to be
rushed setting those plates,
which is understandable.
So we are going to push his flight,
he's going to stay for a few more days,
and we're going to do our best
to push the concrete and the pump truck back.
I'm hoping we can actually do that.
I'm not sure that we will.
So wish us luck, because we have a lot riding
on the timing of this pour
with all the freezing temperatures
and everything that's going to happen this next week.
It's always something.