Lineshaft Driven Machine and Blacksmith Shop Tour

Screw Driver
87 followers
#machinery #motorbikes #occupations #career
A proper look around my workshop as it currently stands! Around 50 feet of shafting and 9 running belt driven machines packed into a garage sized shed.
Thanks for watching!
instagram - iron_jonsey
Hi everyone, Alec here. I've shown individual machines on previous videos but I've realised
never actually the entire shop in a wider context, specifically the line shafting, how it all works,
what kind of building it is. So I'm going to do a bit of a shop tour.
We'll start out here, this beam above me is my gantry outside and that runs through the entire
shop and it's what the line shaft hangs on and it's running at the moment. I'm doing some drilling
so let's go and have a look. So starting with the power source, as you can probably tell it
is electric and up there is a 10 horsepower three-phase motor which runs via a lay shaft
to get speed down and then down through the ceiling onto this main drive pulley which
then goes on to drive the rest of the shafting all the way through the shed. So following it
down now I'm going to start at the back and I'll leave it off so you can hear me and I can hear
myself think. The shaft comes down here and drives a little bench grinder, nothing too interesting
about that but obviously very handy. Moving over I have a rapid or hacksaw which is currently out
of service because it's a bit knackered. I've got two more outside which I'm going to conjoin
with this one to create one decent saw. So that's one project. Keep a tally if you like because
there'll be a lot of those, you'll probably be bingo. I've got fly press and forge. The
forge is an ordinary coal forge, nothing too special about that but it does have
a interesting blower mechanism which was shop made and it's actually a CVT variable speed drive.
So it's belt driven from a small motor on the floor and I have two opposing cones and I can
shift the belt backwards and forwards. So that is quite cool. I got fed up with electronic
speed controllers. So coming towards the rest of the shop I've got the ring rollers which I have an
entire video dedicated to the restoration of those. They are driven from the same 90 degree shaft
which you can just see over there which was driving the drill a second ago and then there's
long belt which comes right over to the counter shaft here and driving the rolls below it.
Super handy machine, probably about 1930s so I did a lot of work to get these to the
condition they're in so go and have a look at that video if you haven't seen it already.
There's the crane I've been working on which I haven't had time to work on
recently. I've been extremely busy with work so that is waiting. Next up is the Drummond which
again you've probably seen on previous videos if you've been watching my channel. Now this is an
interesting machine in that it's a war finish machine so date of manufacture is 1916 according
to the plate and Drummond were taken over by the war department soon after the outbreak of the
first world war to produce lathes for the war effort and famously were working on lathes that
were self-contained motor drive to work in the battlefield machine shops which were built into
the back of lorries. It was this make of lathe that they decided to convert into self-contained
motor and they had a motor bolted on the back here with a big gear drive and a belt and the
motor ran off of the truck's alternator. So coming up to the counter shaft for it. It's got its
original reversible counter shaft so we have a cross belt and an open belt and they can be shifted
to the fast pulley which is this is the driving pulley that's the one that spins. These two are
loose pulleys or idlers and by shifting this handle backwards and forwards I can move the
belts left to right and consequently reverse the machine if I wanted to. This is my Jones and
Shipman 20 inch pillar drill. It's got four speed cone pulley and a power feed as well so that is
gear driven from the top of the quill through a three speed box which is adjustable
by moving this selector up and down and that comes down to a set of miter gears and a worm wheel
which then drives the rack and pinion. And I was just working on my fly press bolster just
drilling some counterbores so the fixing bolts sit flush. I've actually gone a little too far
there but that doesn't matter. Problem with filming things. Now the drill's driven from the
same 90 degree shaft. This is the same 90 degree shaft that chucks a belt over to the ring rollers
over there and the belt drive belt for the drill comes down the back and I don't know if you can
see it's a bit crowded but there is a foot shifter there which shifts the belt from the tight to the
loose and vice versa on the Jones and Shipman. The Jones and Shipman is probably late 19 teens
maybe early 20s. I have a 1921 Jones and Shipman catalogue and the drills are very similar looking
but the base plate is slightly different. This one's got a solid base plate which I
think is probably an earlier thing. However I don't know. It is Morse taper 4 which is quite
handy. I had a another 20 inch model which didn't have power feed it just had a an ordinary sort of
dog clutched lever quill hand feed. Very basic drill and that was a Morse taper 3 so getting
this one was definitely an upgrade. Now this is my Denby horizontal milling machine. Again
probably about the same age as the Jones and Shipman and this has had a complete rebuild.
Everything except scraping the ways because it's more than accurate enough as it is and that's not
a road that I've yet ventured down and perhaps never will. This also has its original counter
shaft with the correct hangers. These are like ring oilers but instead of a ring it's a chain
so there's a small sump in the bearing and a chain which drapes over the shaft and as the shaft
spins the chain picks up oil and deposits it on top of the shaft. Quite clever little things.
Interesting looking hangers. I'm not sure whether they're my favourite but they are original to the
machine so they've got to stay. Again basic basic shifter lever there to turn the machine on and
off. Now this mill is very interesting in that it is extremely complete with a lot of tickable
accessories from the maker so it does have the universal table with the graduated angles on it.
So very useful for helical gear cutting etc. Something I've not yet attempted but
would like to. Fairly simple to set up with powered dividing head which I do have and a
gear set up on the end of the table. Does have its original coolant system as well
so we've got the original cast iron coolant tank which looks like it needs a clean.
A simple belt driven power feed. I have two belts for the power feed one slightly shorter
than this so I can have an open belt. So depending on which way I want to feed I just change the
belts one's open one's crossed. Simple way of changing the direction. The pump on it is original
and was rebuilt by myself. That works I've yet to set up a drive for it so I can actually use it.
The plan is to drive it from the counter shaft that pulley up there and I'll probably have a
second counter shaft somewhere over here to drive the pump and that will have a separate
clutch on it so it can be disengaged. A handy cupboard. Overall a really nice machine. I do
have the extra supports as well so it can be extremely rigid. They clamp to the knee and then
those bars tighten up against the overarm support. In terms of work I had to do to it. It's had a
general clean paint obviously. I've re-scraped in the conical bearings,
taper bearings and I've made a brand new feed screw for the cross slide if you like. So
main reason being it was very slack. There was quite a lot of play in it. It had done
quite a bit of work and also someone had twatted it on the end of the handle I expect
and it was severely bent so I thought well let's have a crack at making a new one.
And that was all done on the Pratt which leads me nicely on to this lathe. Obviously a lot
bigger than the Drummond and Victorian. It was built in Halifax in the 1890s.
Pratt opened their London office in 1892 so I know that it's at least newer than that
and they became limited as well later on in that decade. So I'm positive it was in the mid 1890s.
Just a nice example really of a late Victorian lathe. No bells and whistles,
not very technologically advanced for its day, just a workhorse. I can get 6ft between centres
and it will swing whatever that is, about 3ft I can't remember. So that's with the gap out
at the moment and the gap is an extra section of bed which will slot in here and can be removed
to swing extra diameters. This is a drive pulley I'm working on currently for a customer.
It needs boring out to 3 inches from its current 2.5 and then a new keyway cutting
which will probably be done over on the Redmond here which is the next machine in line on this
kind of older side of the shop. This was built around 1900 and is of course a travelling head
shaper. Again I've done an entire video on this so go and have a look at that.
That is driven directly from the main shaft from this very oily pulley which is annoyingly
just overhanging the bearing there so it's getting covered in oil and flicking it all
over the place. That needs changing. I can't move it any further that way but I can move it
over here somewhere out the way on this dry spot but it does mean I need a new counter shaft for
the Redmond shaper. So I hope you enjoyed that little walk around. What started out for me as
a need for some simple machines cheaply for my blacksmithing business has turned into a full-on
living history project to build the kind of machine shop that you might find in a rural
setting in Britain around the year 1900 to 1915 1920. So those of you who know me you know that's
no surprise because I did exactly the same thing for quite a number of years in the 15th century.
All I've done is move forward a few hundred years and now engineering has been invented
and steam power which is crucial. Hold that thought.
