The Gillo GF is one of the nicest barebow risers I’ve set up and shot, from the excellent fit and finish, to the optimized geometry that makes string walking less of a struggle, it’s one of the best suited risers I’ve tested for barebow archery.
✅ The Good: • High-quality machining and finish with very few flaws • Longer lower half design makes it stable and forgiving for barebow • Easily adjustable weight tunnels for balance and customization • One of the steadiest aiming risers I’ve used
⚠️ The Bad: • Like other Gillo risers, the limb fit and lateral adjustment system can be frustrating. If you tighten things properly, removing limbs becomes impossible without loosening adjustments, a design flaw that really holds this riser back imho.
Overall, the Gillo GF is an excellent barebow riser with thoughtful design, but it still suffers from the same limb removal issue Gillo hasn’t solved yet.
👉 What do you think; deal breaker or small annoyance?
Browse digital downloads, vanes, precision gear, and my archery books: 🌐 https://jakekaminski.com
⸻
📬 Send Mail or Gear
Jake Kaminski P.O. Box 742 Micanopy, FL 32667 Note: Items sent cannot be returned.
⸻
📩 Business Inquiries
Please email me using the address listed in the channel’s About section.
⸻
📖 Chapters
00:00 – Intro 00:29 – Disclaimer 1:41 – Unboxing & Close Up Look 6:51 – Excellent Features 10:16 – Grip Highlight 20:44 – Initial Setup 21:38 – Limb Removal Woes 26:33 – Tunnels 29:35 – First Shots and Tuning 42:23 – 50m Shooting 46:16 – Final Thoughts
Got another review for you here on the channel. Today we're going to be checking out the
Geelo GF 27 inch riser here. What I'm going to do is I'm going to unbox it,
show it to you up close, and then I'm going to take it outside and tune it and shoot it today
as a barebow. So like I said there in the intro, I'm going to be reviewing this
Geelo GF riser that's new for, well, relatively new for this year. And full disclosure, just like
always on the channel, this riser is actually sent to me by Ryan to review before sending it
back to him for him to shoot as a barebow so that way I could have the opportunity of reviewing this
Geelo GF riser on the channel. And if you are interested in grabbing one of these and any of
the products that I will be using on today's video, I will have links down in the description below
and I'll put a card at the top up there too just in case. Those are affiliate links and they
genuinely help this channel out when you click those links before you shop there. It allows me
to buy more gear like this, even though I didn't buy this particular piece, to review on the channel
so you can get it truly unbiased and not through the filtered mouthpiece of a pro shooter because
they ultimately tell you what the company wants you to hear. As here on the channel, I don't have
that. Proudly, I'm not sponsored. I specifically keep it that way when it comes to archery equipment
so that way you get true unbiased feedback when it comes to archery gear. So first and foremost,
this box is ridiculous. I have no idea where this riser comes from and I can't fault them for being
so proud. I love it. You know, the Italians are very proud of their stuff and I really like that.
I would not complain and I would probably do the same, you know, so it's very cool. Anyway, I did
open this up already because I wanted to get some measurements off the riser itself. So full
disclosure there, I've already put my eyes on it but I'll show you it here in a second. What comes
in the actual box is a whole lot of different stuff. You've got your manual, which is quite
thorough actually. We've got a arrow plotting chart for both field and regular target archery,
which is nice to see. It's just a nice little thing that they add into it so you can plot where
your arrows are, keep score, keep it in your quiver. It's just really nice. It's nice to see some
some add-ons. A nice wristband, silicone wristband. You got your hardware kit, which has the clicker
plate, the long extended one, a bunch of various hardware including locking grub screws for tiller
bolts and things like that, and some extra pieces and parts including some L-key allen wrenches.
And then, which we'll get into a little bit later, this will make more sense in a bit,
these are some tunnels. One, well two of them have 516s 24s threaded and tapped so that way you can
put weights and stuff like that, dampers as well as plugs. And like I said, that'll make sense here
in a second because the riser sleeve that it comes in is very nice. So the things that I said
will make sense in a second is for this. They actually go in here and they go in different
parts of the riser and you can put different weights in different configurations, slide them
in and out, have them coming out the back, coming out the front, and there's two down in the bottom
because this is the 27 inch riser, which is huge on the bottom half. The bottom half is massive
compared to the top half, which means it's really made for string walking because it's going to
really help deload that bottom limb, hopefully, and not have to be such a big negative tiller amount
to actually get this bow to feel well when shooting it for a barebow setup. So before I get too far
into the features on the riser, let's take a quick look at the actual riser itself. The actual
machining and finish on this thing is really, really nice. Compared to years previous, in my
opinion, this is a better looking Geelo finish than just about any of the other Geelos that I've
had the opportunity of putting my hands on. I don't see much in the way of flaws, honestly. This
thing is really, really nice and I like the feel of it. The last Geelo, the GT that I reviewed
previously on the channel, had a odd sensory feedback on it because it was blasted and
anodized. This is also blasted or shot peened and anodized, but it doesn't have that same
awful feel to it. This feels fine. The pockets are a little more towards the other way that it felt
before, but I think these are Cerakoted. The pockets are possibly, I'm not entirely sure,
but the riser is definitely anodized and it definitely feels nice in the hand. As far as
the finish on the bow, I don't see much in the way of flaws. The blasting is very nice.
In their manual, they say, hey, this is all done essentially as a post-processing thing,
so you might see some flaws here or there, but I don't see a ton of flaws, honestly. It looks
actually really, really good. The only flaws that I'm seeing is in the actual anodizing itself,
I believe, and there's some streaks, essentially, that I see if I look at it just right.
And there are some machine marks, and I'll show you those here in a second,
but the streaks that I'm talking about, if you look on the sight window here,
you'll see streaks vertically going down this way, and it's most likely from, like I've seen
on other anodized risers, the anodizing dripping off the surface, and you'll see them right here,
like this kind of area dripping downwards down in here. It's very minor, and you really have
to hunt for it, and it doesn't catch your eye if you just look at it quickly. If you're staring at
it, you can start to see it. Now, as far as the machine marks, up on the pocket, this backside,
you'll see vertical lines, not the same kind of drips, but actual, like, lines down the riser
from tooling marks is what it looks like to me, and you'll see the same thing down this backside
as well. But it doesn't look bad. It's just, it's there, and I'm showing you it because I think
it's important to call everything out that I can possibly see. And then, really, the only thing
else, which I think it's actually some sort of lubricant, is in the back of the pocket.
Turn it this way, you see it better. See that white stuff right there? So, I think that that is
some sort of lubricant or something. Yeah, it wipes away. So, I don't know what that is. I'm
gonna assume it's, like, white lithium grease or something of that nature, Teflon grease. I don't
know. I have no idea what it is, but it's some sort of lubricant because it's moving around
as I wipe it. I already went through the manual a little bit, and I can see that there are some
specific guidelines when it comes to the tiller bolts as far as how much you adjust it because
these are the floating pockets. So, the entire pocket pivots back and forth as you increase
draw weight or decrease draw weight, which means you always have the optimal connection point,
actually, here on the dovetail and the tiller bolt, and you don't get extreme weird angles
when you change things because the whole thing pivots. Now, that allows a lot of range of
adjustment, and you have a stock setting where the bow comes, and then you can actually, you're
able to go in five turns or out six turns from factory settings. Now, most bows, when they say
factory settings, that means who knows what because you really don't know what the factory settings
are. Most people, when they get their bow, they throw it together, make adjustments, and go outside
and shoot the thing, and then they have no idea where it was from factory settings, and for me,
I don't trust anything that is factory set because it's set by people. People are imperfect, and they
make mistakes. However, what the manual says, which is really cool, and I'm really glad to see this in
my opinion, is you use the clicker plate, the longer clicker plate that comes with it, you know, the
short one comes installed on it, but you lay it flat against the surface here on where the tunnel
is on the top or where the tunnels are on the bottom, and you use it as a gauge against the
pocket itself. When it's sitting flat against the tunnel and you look at the pocket, it is
to sit flush where the machined hole is on this surface here. So, if you get it in that spot in
that setting where it is flush, because this is a three millimeter thick clicker plate, three
millimeters above this flat surface is where the top of the hole here should be, then you're at
factory settings. So, you can actually use a piece of the bow to use as a gauge to see if your bow is
set at factory settings, so then you know what your limits are in and out from there. I haven't seen
this on any other bow, and I really appreciate that they've gone through this to engineer the bow
and the engineer pieces of the bow specifically to work together so you can get things back to
factory settings. So, that's really, really cool, and I'm very happy to see something like that
because it's just very unique and very different. Now, this bow can be shot in Olympic style recurve
or bare bow, and I know that because they have everything on it. Two plunger holes,
sight block mounts, and two different holes in the front for the clicker itself. Obviously,
it comes with a longer clicker, and something that is a little unique about this bow,
if anybody's been around for a while, they know that all gelos have this. The main stabilizer
bushing is offset away from the sight window to actually allow natural resistance to the canting
that comes from putting a sight and a sight window and all that stuff on one side of the
because the bottom part of the riser is so massively huge, and one of my favorite things
about gelos that I've seen in the past is actually the stock grip. The stock grip
is by far and above the best grip on the market that comes with stock bows. The flatness of it
is very easy to use. There isn't as sharp of an angle on the edge that I would like to see
personally, but it naturally wants to put your hand in the actual correct position.
Normal stock grips put your hand in a position to where it's most comfortable to do this and grab
the bow because most people think, oh, it's a grip. I'm going to grab the bow and grip it,
whereas if I'm doing it with this bow, there's a weird pressure point on this side of the grip here
because it's nice and flat and relatively sharp there, and it's a whole lot more comfortable
to put my palm flat onto the grip and just put my index finger on the front of the riser.
So by far and above, like I said, the best stock grips on the market. They're wood and solid.
They're laminated, so you're actually able to grind them, shave them, file them, sand them if
you want, and you can reseal them to make sure they stay put. Really the only thing that's missing
is that filler spot over here in the corner. When you put your hand in the grip properly,
there's always that hole in the side of the hand there towards the thumb side,
and that can allow a little bit of wiggle room on hand placement, and so really that's the only
thing that I wish was different. So because you have tunnels, you can actually change where you're
putting these stabilizer mounts because as of right now, there's only two stabilizer bushings
on this entire bow. One in the front, the main stabilizer bushing, and one in the bottom behind
the grip. But once you take those tunnel pieces that come with the bow, so you take this piece
here, which has a through hole that is drilled and tapped for 5 16 24, and you essentially take
it in your tunnel, say would want to add one in the top pocket, slide it in, and then you anchor
the thing down with a set screw, and now you have another bushing in the top of the bow. You can put
it in the back, you can put one in the bottom, you can put one out the back on the bottom, you can
in various different locations to change the balance of the bow quite dramatically
with even adding dampers. There's a lot of OEM stuff that this company offers so you can modify
and change the way the bow balances, and it's just a unique thing that I haven't seen before.
The only thing that I'm concerned with, which is easily fixed with this plastic cap that comes
with the bow itself, is maybe you go to a barebow competition, you don't have anything in the top,
and the judge says, hey, you can use the top of your riser as a sight. Well, you just then
throw the plug in it. No, this plug is not for the holes. Or maybe they are if you shove it in there.
Yeah, there. So now it can't be used for aiming because it's not a hole. So, you know, it's really
the only thing that I'm concerned with as far as these tunnels are concerned is just making sure
that you pass tech when it comes to barebow and you're unable to now use this thing as a sighting
reference, which of course you're not going to because it's so high up. It's not down by the arrow.
Judges are ridiculous though from time to time. It is what it is, and so they've got this little
plug here to shut off that hole so you don't get, you know, possibly DQ'd from a tournament.
The limbs I'll be using to build up this bow is the WiaWiz NS XP foam limbs, and before I get it
built up, I want to see the fit of the actual, excellent, the actual limb in the tiller bolt,
and this thing is properly sized. It's the first time in quite some time that I actually have a
properly sized tiller bolt, and I did measure this already with a set of calipers, full disclosure,
and they were 373 and a half thousandths of an inch, which is acceptable in my opinion. These are
finally probably the first set of tiller bolts on an OEM bow that have come out the correct size
in I don't even know how long to be honest, so I'm very happy to see that they do fit,
and the limbs themselves are firm going in, which is great. I have one small concern here.
All right, so what I'm seeing here, and I need to make some adjustments to see
what is going on exactly, but with the limbs loaded in, maybe this will change once the
bow is strung, I'm seeing two very different contact points of the limb on the tiller bolt
on the inside of the tiller bolt, so I'm going to do my best here to show you what is going on.
So if you look at the top, the top is more adequate slash normal. You can see daylight
over on this side towards the actual detent side of the limb, and the fork side is touching the
underside of the tiller bolt. That's not the problem, that is not a big deal at all,
but what I'm seeing on the bottom, which I'm not sure why, so I'm going to experiment,
is it's only touching on this surface, on the surface way out here,
which is going to put a really bad pinch point on the limb and on the tiller bolt,
and there's actually daylight on the actual fork part of the limb, so I can sneak a piece of
plastic in like so there, right, but on this area it just won't go in because there's no daylight.
Before I string the bow up, I want to see if moving the tiller bolts around makes a difference.
So the top went from touching the forks to now touching the whole thing,
the whole surface as I went in, and as I'm going out, it's staying basically the same
as what I showed you, and so now as I have it out a lot more, oh the tiller bolt pivots a lot.
That's probably what's going on. Assuming you should be doing these adjustments with the
bow strung maybe. This is really the only problem I necessarily have with this design,
is if you look, look at the gap here between the tiller bolt and the actual pocket itself,
and see how I can pivot it, because it ultimately pivots on this pivot here,
the pocket itself pivots here, so I can make the tiller bolt pivot independent, which now I can
pull it completely away from the limb, which would be very unsafe to shoot it in that manner,
and much safer to shoot it in that manner. So maybe this is just shifted, yeah, so that was
just shifted so it was only touching in that one spot, and now you can actually see the mark on the
where the tiller bolt was only touching in that one spot there. So I'm going to read the manual
really quick and see if it suggests to make these adjustments with the bow strung, because maybe that
would keep the thing under tension and centered the way it's supposed to be. Personally I don't
like seeing that I can pull the tiller bolt to the point of where the limb is no longer properly
engaged with the tiller bolt, yeah, and so that's that's a bit concerning for me personally. They
call the tiller bolts pre-charged bolts. Pre-charged bolts can be operated with bow loaded
strung for very small adjustments only. When doing large adjustments like adjusting draw weight,
remove the limbs as first you should manually help the neoprene rubber spring under the pocket
to recover less or more compressed status as well as to position the limbs properly
to the new angle. So it doesn't say that this is something that you should be concerned with as far
as the actual position of the tiller bolt, but I can tell you for sure without stringing this bow
that putting the limbs in this the bolts in that position there is very not safe with it all the
way down like this because the contact point of the fork is this side of the center line of the
tiller bolt and so the amount of forces trying to literally pop that tiller bolt head off is quite
extreme. Because I've adjusted everything I want to get this thing back to factory specs really
quick before I string it and just like that I can verify that it is in the factory position because
I didn't count how many turns I took it out when I was messing around with it. Race height
recommendation on this 27 inch riser and long limbs is nine and a quarter inches. So now the
tiller bolts are sitting mostly flush against the limb. I can't get it to shift towards the
dovetail side and angle it this way. I'm not going to try bending it the other way because I'm afraid
of the catastrophic failure risks there. So it looks like it kind of self seated itself for the
most part. So I would just if I was you and you have this bow pay attention to it and make sure
that the tiller bolt itself isn't falling down all the way to that one spot and it looks like
with me screwing around messing with this thing I put a little mark on the front of the pocket
there from when the tiller bolt hit it. So now what I'll do is I'm going to go through the
preliminary setup where I align my limbs to the bow itself to get my center shot set all the
accessories mounted including a g-low drop away rest and get this bow dialed in and ready to go
before I go outside and shoot it. And if there's anything that I notice that needs to be called
out I'll make sure I call it out for you after I'm done getting the preliminary setup checks done.
All right the alignment and setup went really well. Very easy to do. They do have locks that
are installed in the adjustment system so you gotta make sure you take those out of the way
first before you get in there and make your adjustment. Now I did adjust them to my level
of tightness minus a little bit because they are very very small grub screws with very small
hardware. Two and a half millimeter hardware to be exact and two and a half millimeter hex key that
is. And uh previous g-low review video that I did with the GT when I put the limbs in tight
or made my limb adjustment tight and snug how I like it to be couldn't get the limbs out because
I crushed the adjustment plates on the inside which apparently have extreme tolerances
and I just couldn't get the limbs out. So I'm really hoping that I can get the limbs out of
this one because I'd like it to be this tight and I'm hoping they made a little bit of changes
uh since the GT originally came out. Nope. So this is you know something they outline in the manual
saying that you can't over tighten them you got to be careful otherwise you lock the limbs in
the bow and you're not getting them out which it is the case. And uh you know this is basically
in my opinion the biggest downfall of these g-low risers is the lack of ability that you can
tighten these things up to an acceptable level at least for me. I don't want this stuff to move
I don't think you should have to use Loctite there should be enough availability to preload
fasteners to tighten them up to keep them from loosening up they're more than capable of doing
that and what I did there is I just cracked the locks free and now I can get the the limb out so
just the locks themselves it's really is my biggest complaint of this this bow is that
when I have the lock the grub screws tight enough I cannot get the limb out when I have
the grub screws loose the locks loose it comes right out what is the deal I don't know and
I don't have any blue thread locker I don't have non-permanent thread locker that is I only have
permanent red thread locker so I can't lock these things down and let them not get loose on me
and you know this is one of the only companies that I've seen that has locks that lock the
limb adjusters and as you adjust the locks it twists the limb adjusters um I don't know
I mean it's one of those things that I wish was a re was redesigned because it's like
blow on it to make it tight barely making it tight and you know just a another quick little
thing is I think that inside of this area here where the brass piece is that point is very very
sharp and uh there's very minimal chamfer on that area same thing with the pocket edges in this spot
here it's very very sharp and you know I've literally just put these limbs in and out a
being a little rough on the actual surface if I when I'm installing it I'm careful and I'm
keeping that surface of the limb away from the riser as I'm snapping it in place then it stays
fine and it's all good to go but as I go to pull it out I'm dragging it against that surface and
getting it in if I'm not paying attention it really can chew up stuff so not a big deal
it's invisible when the bow is strung up um really not a big problem uh at least not a big issue
like I believe in my opinion having these locks sufficiently usable yeah many people out there
use them don't have any issues don't have them come loose um and you know I'm just one of those
brutes but everything other than that as far as locking the limbs in went very well
the alignment was very easy and everything installed just fine center shot is set
I now have the GELO GMR barebow rest on this thing if you are interested in learning how I
tune and set up my bows I'm going to recommend this book here it's called Tuning for Performance
it is written specifically for Olympic style recurve however it covers a lot of the principles
that I used to align this bow and will use when I shoot bear shafts outside at 30 meters and so if
you're interested in grabbing a copy of Tuning for Performance I'll have links down in the
description below and I'll have a shop tag down at the bottom of the video and I'll also put a
card at the top up there to my website jakecominsky.com where you can grab a copy of that
so now that the preliminary setup is done I want to get these tunnel adapters installed on the bow
with the bushings now so that way I can put some dampened barebow weights in place
and get the balance where I'd like to see it I've been using this ATF DX in 27 inches for my barebow
recently so I'm going to steal the weight off of it and throw the same configuration of two 14 ounce
Kominsky Archery dampened barebow weights on the bottom one in the main stabilizer bushing and one
in the low bushing and then have one eight ounce in the top I'll grab a ring and see if they pass
through of course to make sure they're legal that's better balance is much much better now
yeah now the string sits nice and vertical just like I like to see got a ring here
so I pass the bottom no problem pass the middle and of course that should mean I should pass the
top with flying colors I could adjust these a little bit and optimize them and add a few spacers
get a little bit more forward balance which I might as well do we do have shims that come with
our barebow weights so you can extend them out a little bit further and get a little bit more
forward balance and kind of push the limit as to what you can actually get and I can get a whole
lot more out of this thing what's nice about this system is I can't get the bottom weight through
the ring so I'm going to crack this bottom set screws free slide the actual weight in a little
bit and do my best to maximize how far out I can put this thing just get clearance so what this is
allowing me to do is getting the maximum amount of I guess resistance to rotational inertia and
balance forward on the bow itself because adding these little shims and sliding the tunnels in and
out just puts the weights a little bit further forward and gives it that little bit more of
forward tipping balance which I find is really nice for me when it comes to shooting barebow
and it comes to getting proper reaction from the actual bow tipping forward and jumping a little
bit harder out of the hand it just feels far more stable for me so right here is just about as far
forward as I can get so you can get an idea here the eight ounce width I've got a lot of spacers
and the stack all the way out got the main stabilizer bushing and then the lower bushing
these definitely are gonna kill a lot of vibration when it comes to the bow and I'm excited to get
outside and get some arrows through this thing finally outside and I'm here at 20 yards I have
a camera downrange so I will show you the impact points the entire time and I'm starting here at 20
yards because I have no idea what my tune is going to be and I have 450x10s in my quiver
really want to get this bow tuned up with these so I can shoot lighter draw weight and I'll give
you some feedback as to how this GELO GF 27 inch riser feels and I do have the GELO GMR
drop away rest as I've already said and I have it set in the springy mode just because
I feel like trying it in the springy mode today on this bow currently running a tab sear at the
moment so if you see me moving around funny once I'm at full draw that's what I'm working on
my crawl is for sure way off I can't quite get down enough because of what I've got going on
with my tab here using it that piece as my grip my tab sear so I'm just going to get what is an
approximate 30 meter crawl somewhere in that range and aim at the bottom of the bail and shoot for a
group and then shoot the bear shaft plunger was loose got that all dialed in now
all right now the bear shaft okay so as I was hoping and suspecting extremely weak which is
great now I can go down a lot in my draw weight so I'm gonna go down pull those arrows and take
a few turns out of the draw weight here within a little bit more acceptable tune range with these
450x10s and apparently I forgot to hit record on the camera downrange sorry about that so
where my bear shaft went was basically in the blue to the right I'm gonna start with
four turns out I don't know if that's gonna be too much or not and I suppose I should be
checking tiller all right so I'm going to be curious as to what I should be worried or not
worried about with the tiller bolts I'm going to try to get them to sit flat against the limb
because that's where I would prefer them to sit when this thing is strung up I think four turns
was too much based on the feel of the limb now oh yeah so light limbs are sitting flat against
tiller bolts so that's good quick check my tiller I would like it to be negative
even to negative it is right now positive all right so we got about an eighth inch negative
on the bottom I'm not going to go the full quarter like I normally do because this bow
is so asymmetric meaning the bottom part of the riser is so long that's what really makes this
thing a nice barebow riser in my opinion is that longer pocket on the bottom makes needing to use
so much negative tiller much of a lesser thing when we're string walking especially with me
string walking so deep I typically need a very big negative tiller at least a quarter inch if
not bigger in order for the thing to aim steady and to feel good at full draw yeah those arrows
are flying much better already all right and now the bear shaft way closer this is getting good
actually so I'm going to because I'm hitting left back some of the plunger tension off first
and then I will probably take another half a turn or so out of the limb weight but it's very very
close where I think I might already just go ahead and step back to 30 meters at this light draw
weight the bow is quite quiet feels decent vibrations quite minimal overall feels quite
dead in the hand and it's very quiet more fletched and then a bear right now the bear shaft all right
it looks to be stiff and high knocking point from here I am going to go down and verify that and
come back and make some adjustments I think I'm going to put that half turn back into the bow
draw weight wise hold that one left a little bit
for sure need some adjustment on my tab sear placement causing my tab to shift in my hand
after it pops before I let it go that is obviously not ideal those two popped and moved
right and a bear shaft can't be shooting while I have huge movements of my tab going
so I put a quarter turn of draw weight back into the bow and I had to adjust my tab sear position
because what was happening was it was moving my whole tab was moving the moment my thumb slipped
off of that tab sear face and it was causing a very changing impact point downrange between low
and high and this is actually why I do basically all my reviews olympic style recurve is because
it's easy to just throw those things together and be really close whereas barebow there's so many
various changes crawls and because of that tune and and so there's just a lot going on so it's
definitely much easier for me to just review it as a recurve instead but because this thing
is so barebow oriented I really wanted to get this thing done as a barebow review
let's see what the bear shaft does really weak again this is so weird how it's going from stiff
to weak to stiff to weak all right let's try this again I'm hoping this will be close now
I don't understand why I'm continually going weak I was noticing when I used this g-load gmr
drop away rest the review of it if you haven't seen that one by the way I'll have links in the
description below in a card at the top up there so you can check out the review of the gmr drop
away rest when I swapped it to springy which it's in the mode right now springy I believe I hit much
weaker and it's something I've never seen before I've never had the option to switch it between
springy and drop away any other rest so it's something that I saw that was weird and maybe
this is causing me some of these issues because maybe that's what's ultimately causing this tuning
problem because the draw weight that I'm shooting is excessively low at the moment it's getting to
be a little frustrating because I just want to be shooting I don't want to be messing around with
this tune so long yeah I mean as you can hear the bow now that the draw weight is so low the limbs
are very unhappy I'm gonna shoot one more arrow like that yeah it sounds terrible now those arrows
are flying awful definitely can't shoot it in this configuration as it is something's something
funny is going on so because the bow just sounds like something is clearly wrong I am going to
increase the draw weight again back up one more turn because I'm going to do a turn and a half
because it just it did not seem happy at this lower draw weight and the arrows continue to
get weaker and weaker so maybe I'm getting some sort of weird false tune here I'm not entirely
sure but I am just going to go up this turn and a half and we're going to step back to 50 meters
and I'm going to shoot this bow as is in its current configuration which is
tuned enough the arrows were flying much better up at that draw weight and and then I'll let you
know how the thing actually is as far as how it aims at 50 meters and how steady it holds
because 30 meters on a big 122 centimeter face you don't really get much in the way of feedback
there I think that there's just something going on with this GMR rest set in the springy
position that just really throws off something and I'm not really quite sure what it is
let's shoot a few ends here at 50 meters before I give my final thoughts here of this
Gelo GF 27 inch ride guessing on my crawl though got to get that dialed in here
definitely aims really nice it's very steady considering I only have an eighth inch of
negative tiller usually I'm well over a quarter inch to get this kind of stability with the
weights and the configuration that I've got it so the longer portion the bottom half of the
riser being longer like it is is a really really nice feature for barebow I mean there is no
struggle to aim up and down it's just just sits right there I'm gonna go get them seem to sometimes
sit a little low but it can I can lift it up easily it's really very responsive to what I
need it to do so that is a big improvement compared to what a standard ILF setup is that
doesn't have this longer portion on the bottom half so I'm half slipped on the tabs here shot
it anyway because it felt like it moved and then I didn't want to let it go so that's where
oh feels pretty happy though definitely can feel a little bit of limb flutter out of the limbs
but you know it is barebow there's not much in the way that you can dampen those there's just
no stabilizers obviously but I can feel some relatively large amplitude low frequency oscillations
it dies quickly after about two three hits it feels like it's coming from exclusively in the
the more I shoot this the more I like that bottom limb for the lower riser being longer
that one high left all right so I am going to take you down there and we're going to check
out that last group there and then I'll give you my final thoughts here on this Gelo GF
27 inch riser all things considered this is actually a pretty solid group from 50 meters
considering I have no idea what's going on with the actual tune and I'm just really trying to
work through my tabs here within the last 50 to 100 shots so this is definitely something that I'm
looking forward to working for working more on my tabs here that is to get it a little bit more
optimized and I'll probably do a standalone breakout video on that alone so that way you
can kind of see what I'm working on and my methodology there so that way you can better
understand what I'm actually trying to accomplish but let's talk about the Gelo GF 27 inch riser
that I've got here as far as the things that I really like about this riser the finish on this
is amazing the fit and finish is both excellent the tiller bolts are proper sized they're just a
smidge under 375 thousandths they're one and a half thousandths under that which is basically
nothing they are great as far as the tolerance of the tiller bolts are concerned and I'm very happy
to see that it's the first riser in a long time that I've seen that be within an acceptable range
that I believe is very very important now for the actual finish like I said it's excellent the
anodizing is great it has this little uneven markings here or there that I showed you
originally when I unboxed it but you can't really tell you have to really be looking for it in order
to see it it really just it kind of looks like it maybe is a little dirty for lack of better terms
but if you can't tell you probably won't tell in person the idea of the weight tunnels is very nice
and I like that you can adjust the depth of them and there's various different accessories that you
can mount in these holes that allow you to add bushings for stabilizers or dampened variable
weights in this case or you can put in various different pieces that change the balance the feel
the look and various different performance aspects of the bow itself the grip by far and above the
best grip of any stock bow that I've put my hands on at least that I can recall it's flat it's simple
it's got a decent edge on it it's not sharp really the only thing that's missing is that filler piece
for the actual thumb side of the grip when you're putting your hand in the bow that's the only thing
that is missing otherwise you know out here in Florida I'm sweating it's not exactly cool out
my hand didn't once even feel like it was slipping and this is a huge win in my opinion
other massive wins on the riser itself is you can actually put it back to literally factory spec
settings and verify that you set them or the factory set them at factory spec settings because
there is a guide in the manual on how to use the extended clicker plate that comes with the bow
as a gauge on the front side of the riser against the pocket itself and you can adjust that to get
to exactly factory settings which is amazing the draw weight adjustment from really low to really
high you can get yourself into a bind but you can also grow with a set of limbs over time if you're
looking to go up and draw weight you have a lot of room for adjustment there on the draw weight that
you can get out of this riser and that's really really a great feature another thing that I liked
about the riser is its natural balance for bare bow you don't have to go really huge on the negative
tiller setting you don't have to go in that quarter inch plus negative tiller range to get the bow to
hold halfway decent like you do with a standard olympic oriented ilf riser you know this bottom
portion of the riser from the grip down is massive compared to the top up if I pull an arrow and go
from the pivot point of the grip to the tiller bolt right and then I go from the pivot point
of the grip to the bottom you'll see that I don't even make it within you know an inch see how much
shorter I am I should be way down here I'm way up here I'm over an inch maybe an inch and a half
shorter on the top than the bottom what that does is it naturally deloads the bottom limb when you're
string walking when you're crawling down the string and it makes the bow feel more pleasant
the limbs are naturally more balanced that way and it holds better than pretty much any bare
bow I've set up as far as the the reaction to when I'm too low or too high sometimes I can get the
bow to hold really steady not this bow another bow get it to hold really steady but it doesn't
want to react if I need to lift the point up a little bit as my aiming point's just slightly low
this bow is very reactive and it feels very balanced even at the deeper crawls it's just
something that I really am a big fan of on these gelo risers personally speaking now other things
about the bow that I'm not necessarily a huge fan of would be the number one first and foremost
the actual grub tightening mechanism for the limb adjustments for left and right lateral
adjustments this is something that I had issues with on the gelo gt they haven't changed anything
here on the gf risers and basically they're according to gelo the tolerances that they use
on the female receiving end of the dovetail for the ilf system their tolerances are so tight
and it's made of brass which is a little bit softer I believe they're made of brass if not
they're just anodized aluminum so they're not super soft and when I tighten up the grub screws
on either side without the locks to what I would accept for me as far as being reasonably tight so
they won't come loose they're fine the limbs come in and out no problem but as soon as I go to put
the locks in and I give any sort of reasonable amount of torque not even me not my level of
torque I have a tendency to over tighten things because I've had things come loose in tournaments
that have cost me points and cost me places so I like to tighten things down so they don't move
and I cannot tighten down the limb adjusters or the locks to a reasonable level of tightness to
make sure that they don't come loose gelo says to use non-permanent loctite so a blue loctite
to hold them in place but normal fasteners tighten to a reasonable level that is suited
for their size fastener should not vibrate loose under any circumstance on a recurve bare bow
compound or anything else it should stay tight at least in my opinion and I can't get these things
tight enough to that level so they don't come loose so you're forced to use blue thread locker
and I don't want to use thread locker this isn't my bow this is Ryan's bow and I don't want to lock
the limb alignment system in place that's going to be up to him to get it to work how he likes to do
it it's just in my opinion the biggest downfall of these gelo risers to say that it's other limbs
fitments and it doesn't work in there because their tolerances aren't quite right well these
are win and win limbs gelo limbs to my knowledge are made by win and win should be the same
tolerances I should be able to get these things out after I tighten the adjustment system to a
reasonable level not over tight not American tight reasonable tight just a reasonable level level
so really I mean I think that's just about the only thing that I don't like I'm not a huge fan
of the stabilizer bushing being offset you know the what two millimeters I believe that they say
it's an interesting idea to offset the weight of the actual you know the sight and the sight window
being on this side but it makes aligning the bow a little bit more difficult and it would be simple
if it was just in the center I can always add an ounce to the left or do something else for
my balance to get the sight window and the sight bar offset if I choose to ever shoot this thing
as an Olympic style recurve really that's the only negative things that I can think of of this bow
just the limb adjustment the stabilizer bushing yeah I can't think of anything else really if I
did say anything earlier it's so inconsequential that it didn't make an impact to affect my opinion
on the bow at the moment so if you are interested in this gelo gf riser especially for barebow I
would highly recommend it links down in the description below that is an affiliate link as
well as all the other gear that I've got listed down in the description below those are affiliate
links genuinely helps this channel out if you click those links before you shop there each and
every time those cookies last roughly for about 30 days so if you click those links once every 30
days and shop there genuinely really really helps the channel out will allow me to purchase these
pieces of equipment to do the reviews honestly so you get them from an unbiased source and you're
not getting them from a pro shooter you know really I wish I could have got this thing dialed
in a little bit better tune wise I suspect it's something that has to do with the springy setting
of this springy rest I don't know what I'm doing wrong what I'm doing different but I'm getting
this really weird weak tune out of the bow that I should not be getting and I went so far down
in draw weight that I would guess I was in the mid to low 30s trying to shoot 450 spine arrows at
less than a 29 inch draw length I really don't think that should have been happening so if anybody
has found out in their experience playing with this gelo GMR magnetic rest in the springy setting
please comment below help me out help others out as well because I like the rest personally I just
wish that the tuning function was a little bit better in regards to it in the springy setting
and one final thing before I end the video we've got apparel we've got hoodies we got t-shirts we've
got stickers we've got a few different things that we're working on and we have currently added to
the USA shop shortly will be added to the EU shop as well so you'll be able to get some of our
apparel from in-house right now we've got only barebow designs as you can see I've got the I am
string walker 2.0 and I've got another version of a string walker shirt available as well both in
the hoodie and in the shirts and they are ultra premium highly soft ring-spun cotton shirts 100
cotton or super super soft hoodies and a few different stickers you can throw on your water
bottles your cases things like that and we're really just trying to work on bringing up the
quality of the apparel and stuff that we have because we're bringing in in-house because those
third-party fulfillment centers they just really aren't up to our standards and we're working on
keeping things in-house as much as possible and big thanks again to Ryan for letting me
out his riser and play with it before I send it to him so he can shoot it this indoor season