Carving a Yarn Bowl (Part 2)

Ceramic Art Studio
35 followers
1 Video View·Dec 15, 2025
Right so this is carving before I've trimmed the foot which seems to work okay.
The clay is leather hard so it's a nice dryness to carve. You can let it get a bit drier
especially before neatening up actually. It can be worth doing the two stages of this
at different points just because you want to get crisp edges. You want it to be
on the drier side but there are some advantages to not waiting until it will bend rather than
snapping if you go on the wetter side. So depending on how careful you're going to be
and your clay body you'll have to figure out where the right balance is. I'm using
one of the tube hole cutters rather than a drill bit for this. I use the drill bits when using my
hole cutting guides because that marks the centre and a drill bit cuts from the centre so it's very
easy to locate. These aren't so good with the hole cutting guides because you can't easily mark the
exact centre and cut around it but from this it's a very easy way of just cutting a circle.
So I've got it on an old t-shirt. I wouldn't normally do it on the wheel but it's just an
easy place to record so I'm going to keep going here and go probably just below halfway up from
the base. When doing it this way I'll post a video. There's a another way of making it
that's a bit simpler than this where you can go a bit lower but make my starting hole
and then you can draw on greenware with the sharpie and it'll burn off completely in the
bisque. So what I want to do is come out that hole about halfway up and then loop around underneath
trying to stay a similar distance away from the hole and then up and then the other line
comes off around the top. You don't want to leave too narrow close that bit down that's
wider than it needs to be but you don't want this to be too narrow because any drip coming off that
will close it if they're just a few millimetres apart so it's worth erring on the side of
too wide rather than too narrow. Then I'm using a scalpel for this it's not
the sharpest in the world anymore just because I've cut clay with it too many times. It's hard
to do this well with it facing the camera but hopefully I can do it all. So the real trick
is don't cut all the way out of the rim so what I'm doing is I'm going to cut across like that
and you can actually leave this piece in there if you want while it dries but it does make
cleaning it up a bit trickier so I am going to remove it but by leaving the rim intact
it retains pretty much all the strength that it normally would
even though you've carved a lump out of it. If you were to cut completely out it would be free
to just collapse as it wanted. Now it wouldn't at this level of dryness but it would take on
far more strain as it dried so the clay would want to warp and the thing with clay is that
it would remember that and in the firing it would be far more likely to warp. So trying to
get this out without knocking the bit that you've left. You can carve that shape yeah so as I was
saying leave a bridge there and then yeah that's not the neatest I've ever done. It's easier when
you're not doing it towards the camera so when you do it do what you saw rather than what I did.
You see what I mean? Have it face towards you and then what I do is I use the scalpel
to miter the edge and this is where the trick to getting it really neat comes in because you can
miter up to the rim and so that now when you cut it off that edge is already neat. You see what I
mean? Basically you're going to remove the clay from the middle with I use a hacksaw blade because
you can very gently saw away at it and then bone dry clay will go with the saw without too much
fight but yeah if you angle the edge like that and then just keep that going up to the rim
then when you cut it off you will actually get a near perfect edge to the whole thing and you can
sponge it to just finish it off but it means you've got all the strength of a complete rim
while still not having much clay to remove when it's bone dry to to open that up. So anyway with
yarn bowls as I understand it I'm obviously no expert but I believe you need one hole or you
can have some people do it where there's kind of multiple like it comes down and splits you've got
multiple yarns if you want them but one hole has to go out of the top because the whole point is
you don't want to you want to be able to remove the ball without it going through a hole so
the holes have to be able to reach the top and you can put the yarn in and out without
feeding it through anything but they will also have two holes generally next to it or one or
two holes or something like that and as I understand it that's for the needles to go in
but I'm not entirely sure about that it seems to be the way that they're all done someone told me
for the needles to go through which sort of makes sense for because obviously you wouldn't put the
thread through it for exactly the same reason that this one's open because you then can't remove it
without rolling the whole ball through so yeah so what I would then do is just add two more holes
and then I use a mitering no counter sinking sorry bit these holes are right on the limit of
what it can do and the clay is a bit wet so it's not going to do the best job ever but if you let
it firm up a bit first then it doesn't it it cuts the clay rather than just pushing it out to the
but it's a good way of beveling the outside of a hole and I'm going to neaten the rest of that up
a sponge in that bit slightly then leave it for half an hour or so and trim the foot
this is another way of doing it much easier to cut the downside to this is that if you're using
interesting glazes that will flow and pull you've got less surface for them to do that
the upside is it doesn't weaken that part as much so depending on your clay and how hot you're
firing and how long the firing and whether or not it will warp this might be a better bet
so it's just literally homemade with the cutter and then just cut around again I'm leaving a
bridge in I'll neaten that up in a second but that's going to be what gives it the strength as
it dries right this is the next day and this is not quite bone dry but pretty dry and I've got
an old hacksaw and it's actually a jigsaw blade but you want something with a fine tooth
and if I'm going to do more of these I'm going to get a better one because this one's a bit wobbly
but it's just one that was kicking around in the garage something with a fine tooth so you can
just very gently ease through the clay and it'll crack along the lines that you scored in
you can still use a scalpel to clean them up roughly and then a sponge to finish the job off
as for what sponge I use I throw with um zine porcelain sponges and I go through one every
month or two and you can see the difference this is a relatively sort of a couple of weeks
older thing so starting to wear out but how much thinner they get as you just ruin them basically
and I throw quite a lot well not compared to production product but yeah I get through them
but the nice thing is as they wear out and get thinner and more kind of falling apart
they become more flexible they've got quite a fine structure to them because they're the
porcelain version they do some coarser ones for stoneware and things but you know I use this for
stoneware it's just a nice sponge but as it becomes thinner and more flexible it is ideal
for getting round awkward shapes so I just use it to as you can see you can bend it around
the clay and just round that off um once you've got it rounded but it's still a bit wet you can
use one of the um silicon shaping tools to burnish it back to smooth because the grog will
be exposed this has quite a fine grog so it's just slightly rougher not too bad if you've got
a really coarse stone where you'll really feel the grog as you sponge back it gets more and more
sandpapery with this just gets a light texture not the end of the world but given that the idea
is that yarn is going to pull through this you want this to be as smooth as possible and these
tools are quite useful for that so just as you sponge just burnish it back to smooth and then
that will be your finished yarn ball and once you've sponged it and smoothed it's basically
not a lot more you need to do um in terms of firing I don't think it really there's
there's a huge amount you can do at that point because it shouldn't warp in the bisque firing
and in the glaze firing you can't support it without it sticking so I think so long as you've
managed to avoid stress up until the bisque firing you're going to be as okay as you could possibly
be in the glaze firing and that will come down to how thin you've carved it and how strong your
clay is and how hot you fire if you're going to cone 10 with a really long hot firing um and your
clay can only just take it you might get it you might be warping I don't I don't really know in
cone six firings with this clay it generally seems to be okay um but yeah just as with all things
clay the trick is to try and avoid stress that's going to come out later and by leaving that bridge
in you keep it as strong as possible until the point at which it it can't move anywhere now and
it's basically basically solid so it's not going to feel much strain I guess the thing to do is in
the firing probably fire bisque fire it upright and don't stack them you know you could stack
something inside if you want to save space so like that but don't put another bowl on top because
you'll be forcing it out um but but really just be a bit more careful with this than you would
another bowl and it probably will be right
